Harbor Freight Tools 61613 User Manual

Harbor Freight Tools 61613 - Electric Chain Saw Sharpener Manual

Get Harbor Freight Tools 61613 - Electric Chain Saw Sharpener PDF manuals and user guides View all Harbor Freight Tools 61613 manuals
Add to My Manuals
Save this manual to your list of manuals

Harbor Freight Tools 61613 manual content summary:

  • Harbor Freight Tools 61613 | User Manual - Page 1
  • Harbor Freight Tools 61613 | User Manual - Page 2
    moderate injury. Addresses practices not related to personal injury. IMpORTANT SAFETy INFORMATION General Tool Safety Warnings Read all safety warnings and instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and
  • Harbor Freight Tools 61613 | User Manual - Page 3
    at all times. 14. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories. 15. DISCONNECT TOOLS before servicing; when changing accessories, such as blades, bits, cutters, and the like. 16. REDUCE THE RISK OF
  • Harbor Freight Tools 61613 | User Manual - Page 4
    2-prong plug.) Grinder Tool Safety Warnings For your Own Safety Read Instruction Manual Before Operating Grinder 1. Wear ANSI-approved eye protection. 2. Use may result in a risk of injury to persons. 17. When servicing use only identical replacement parts. 18. Only use safety equipment that
  • Harbor Freight Tools 61613 | User Manual - Page 5
    et seq.) 26. The warnings, precautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may a doctor and then have regular medical check-ups to ensure medical problems are not being caused or worsened from use. Pregnant women or people
  • Harbor Freight Tools 61613 | User Manual - Page 6
    section. Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram near the end of this manual. Mounting Note: The Sharpener must be mounted on a horizontal surface. 1. Position the Sharpener on the mounting surface so that the mounting stop
  • Harbor Freight Tools 61613 | User Manual - Page 7
    Functions Vise Handle Depth Adjustment Knob Depth Adjustment Lock Nut SAFETy SETUp OpERATION Handle Vise Cable power Switch Chain Stop Adjustment Knob Depth Adjustment plate Depth Adjustment Stop Chain Stop Clamp plate Vise Safety Guard Chain Stop Lock Nut Item 61613 Chain Roller Knob
  • Harbor Freight Tools 61613 | User Manual - Page 8
    SAFETy SETUp Operating Instructions Read the ENTIRE IMpORTANT SAFETy INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Tool Set Up TO pREVENT SERIOUS INJURy FROM ACCIDENTAL OpERATION: Turn
  • Harbor Freight Tools 61613 | User Manual - Page 9
    Angle Adjustment Knob. b. Turn the Chain Roller until the first left-hand cutter is in position. Then, engage the Chain Stop. c. Follow instructions for 5. Sharpening the righthand cutters: beginning at c. and ending at i. Cutting Edge Gullet Figure G: Left-hand Cutter 7. Clean and oil the chain
  • Harbor Freight Tools 61613 | User Manual - Page 10
    SAFETy Maintenance and Servicing procedures not specifically explained in this manual must be performed only by a Do not use damaged equipment. If abnormal noise or vibration occurs, have the problem corrected before further use. Cleaning, Maintenance, and Lubrication 1. BEFORE EACH USE, inspect
  • Harbor Freight Tools 61613 | User Manual - Page 11
    SAFETy Troubleshooting problem possible Causes Tool will not start. 1. Cord not connected. 2. No power loads. 3. Turn off tool and allow to cool. Press reset button on tool. 4. Have technician service tool. Eliminate use of extension cord. If an extension cord is needed, use one with the proper
  • Harbor Freight Tools 61613 | User Manual - Page 12
    pLEASE READ THE FOLLOWING CAREFULLy THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
  • Harbor Freight Tools 61613 | User Manual - Page 13
    Record product's Serial Number Here: Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SAFETy SETUp OpERATION MAINTENANCE Item 61613
  • Harbor Freight Tools 61613 | User Manual - Page 14
    SAFETy parts List and Diagram parts List part Description 1 Screw 2 Grinding Wheel Cover 3 Outer Flange 4 Grinding Wheel 5 Inner Flange 6 Screw 7 Screw 8 Motor Cover 9 Nut 10 Depth Adjustment Lock Nut 11 Depth Adjustment Knob 12 Power Switch 13 Main Handle 14 Vise Handle 15 Back
  • Harbor Freight Tools 61613 | User Manual - Page 15
    Assembly Diagram SAFETy SETUp OpERATION MAINTENANCE Item 61613 For technical questions, please call 1-888-866-5797. Page 15
  • Harbor Freight Tools 61613 | User Manual - Page 16
    Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16