Harbor Freight Tools 62459 User Manual
Harbor Freight Tools 62459 - 14 in. 3-1/2 HP Heavy Duty Cut-Off Saw Manual
 |
View all Harbor Freight Tools 62459 manuals
Add to My Manuals
Save this manual to your list of manuals |
Harbor Freight Tools 62459 manual content summary:
- Harbor Freight Tools 62459 | User Manual - Page 1
Manual & Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product's serial number in the back of the manual our technical support at: for assembly and service may not be - Harbor Freight Tools 62459 | User Manual - Page 2
injury. Addresses practices not related to personal injury. IMPORTANT SAFETY INFORMATION General Tool Safety Warnings WARNING Read all safety warnings and instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and - Harbor Freight Tools 62459 | User Manual - Page 3
at all times. 14. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories. 15. DISCONNECT TOOLS before servicing; when changing accessories, such as blades, bits, cutters, and the like. 16. REDUCE THE RISK OF - Harbor Freight Tools 62459 | User Manual - Page 4
cord or plug is necessary, do not connect the equipmentgrounding conductor to a live terminal. 4. Check with a qualified electrician or service personnel if the grounding instructions are not completely understood, or if in doubt as to whether the tool is properly grounded. 5. Use only 3-wire - Harbor Freight Tools 62459 | User Manual - Page 5
may result in a risk of injury to persons. 16. When servicing use only identical replacement parts. 17. Only use safety equipment that has et seq.) 26. The warnings, precautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur - Harbor Freight Tools 62459 | User Manual - Page 6
a doctor and then have regular medical checkups to ensure medical problems are not being caused or worsened from use. Pregnant women or the tool as explained in this manual. If any abnormal vibration occurs, stop use immediately. SAVE THESE INSTRUCTIONS. Setup Operation Maintenance Page 6 For - Harbor Freight Tools 62459 | User Manual - Page 7
Safety Specifications Electrical Input 120VAC / 60Hz / 15A Motor No Load Speed 3,500 RPM Max. Accessory Diameter 14″ (355mm) Recommended Cut‑Off 14″ Cut‑Off Wheel for Metal (Item 44814, sold separately) Wheel Types 14″ Cut‑Off Wheel for Masonry (Item 44815, sold separately) Cutting Capacity - Harbor Freight Tools 62459 | User Manual - Page 8
Operating Instructions Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Tool Set Up Safety Setup Operation TO PREVENT SERIOUS INJURY FROM - Harbor Freight Tools 62459 | User Manual - Page 9
Safety Setup c. Rotate the wheel 90° and repeat the test until the entire wheel has been checked. d. An undamaged wheel will give a clear tone. If cracked, there will be a dead sound and not a clear ring. 8. Replace with the new cut‑off wheel, and reassemble the parts shown in Figure B. The - Harbor Freight Tools 62459 | User Manual - Page 10
Safety Work Piece and Work Area Set Up 1. Designate a work area that is clean and well‑lit. The work area must not allow access by children or pets to prevent distraction and injury. Setting Up an Angle Cut 1. To cut at various angles (up to 45º), adjust the Angle Scale (80) by loosening the two - Harbor Freight Tools 62459 | User Manual - Page 11
10 2. To release the workpiece, loosen the Vise Handle a few turns, lift up the Quick Release and pull the Vise Handle open. General Operating Instructions Quick Release (82) Place Workpiece Here Vise Handle (13) Figure G: Vise Components TO PREVENT SERIOUS INJURY: DO NOT OPERATE WITH ANY GUARD - Harbor Freight Tools 62459 | User Manual - Page 12
Safety Maintenance and Servicing Procedures not specifically explained in this manual must be performed only by a qualified Do not use damaged equipment. If abnormal noise or vibration occurs, have the problem corrected before further use. Cleaning, Maintenance, and Lubrication 1. BEFORE EACH USE, - Harbor Freight Tools 62459 | User Manual - Page 13
Safety Troubleshooting Problem Tool will not start. Possible Causes 1. Cord not connected. Likely Solutions 1. or wear. (Carbon or rattling. brushes or bearings, for example.) 4. Have technician service tool. Eliminate use of extension cord. If an extension cord is needed, use shorter/ - Harbor Freight Tools 62459 | User Manual - Page 14
Diagram Safety Setup PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR - Harbor Freight Tools 62459 | User Manual - Page 15
Assembly Diagram Safety Setup Operation Maintenance Item 62459 For technical questions, please call 1-888-866-5797. Page 15 - Harbor Freight Tools 62459 | User Manual - Page 16
Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
 |
 |
Cut-Off Wheel sold separately.
Visit our website at: http://www.harborfreight.com
Email our technical support at: [email protected]
3-1/2 HORSEPOWER
14
"
INDUSTRIAL
REV 14k
Owner’s Manual & Safety Instructions
Save This Manual
Keep this manual for the safety warnings and precautions, assembly,
operating, inspection, maintenance and cleaning procedures.
Write the product’s serial number in the
back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference.
When unpacking, make sure that the product is intact
and undamaged.
If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
Copyright
©
2014 by Harbor Freight Tools
®
.
All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally.
Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.