Harbor Freight Tools 62520 User Manual
Harbor Freight Tools 62520 - 8 in. 5 Speed Bench Drill Press Manual
 |
View all Harbor Freight Tools 62520 manuals
Add to My Manuals
Save this manual to your list of manuals |
Harbor Freight Tools 62520 manual content summary:
- Harbor Freight Tools 62520 | User Manual - Page 1
manual and the receipt in a safe and dry place for future reference. REV 17a Visit our website at: http://www.harborfreight.com Email our technical support slightly from the product described herein. Tools required for assembly and service may not be included. Read this material before using this - Harbor Freight Tools 62520 | User Manual - Page 2
moderate injury. Addresses practices not related to personal injury. IMPORTANT SAFETY INFORMATION General Tool Safety Warnings Read all safety warnings and instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and - Harbor Freight Tools 62520 | User Manual - Page 3
at all times. 14. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories. 15. DISCONNECT TOOLS before servicing; when changing accessories, such as blades, bits, cutters, and the like. 16. REDUCE THE RISK OF - Harbor Freight Tools 62520 | User Manual - Page 4
to connect this tool to a different outlet. For Your Own Safety Read Instruction Manual Before Operating Drill Press 1. Wear eye protection. 2. Do not wear gloves, may result in a risk of injury to persons. 8. When servicing use only identical replacement parts. 9. Only use safety equipment that - Harbor Freight Tools 62520 | User Manual - Page 5
et seq.) 18. The warnings, precautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may a doctor and then have regular medical check-ups to ensure medical problems are not being caused or worsened from use. Pregnant women or people - Harbor Freight Tools 62520 | User Manual - Page 6
Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram near the end of this manual. SETUP OPERATION Mounting Secure the tool to a supporting structure before use. Before assembly, bolt the Base to a flat, level, solid workbench capable of - Harbor Freight Tools 62520 | User Manual - Page 7
1. Loosen the two Set Screws (9) on the right side of the Headstock (39) so they will stay clear while installing it. Figure B: Installing Table Support Headstock (39) 2. With assistance, lift the Headstock above the Column, and gently slide it down the Column as far as it will go. Make sure - Harbor Freight Tools 62520 | User Manual - Page 8
Operating Instructions Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all Scale, turning the drill ON, and drilling to the required depth using the Scale as a guide. Lock Nut (57B) Adjustment Nut (57A) Drill Stop depth gap Pointer (56) Scale Stop - Harbor Freight Tools 62520 | User Manual - Page 9
SAFETY SETUP Changing Drill Speed Before changing drill speeds, make sure the machine is switched OFF and UNPLUGGED. 1. Open the Pulley Cover. 2. Loosen the Motor Tension Knob (10) on the Headstock (39), and move the Motor (14) towards the Headstock to relieve tension on the V-Belt (60). 3. - Harbor Freight Tools 62520 | User Manual - Page 10
SAFETY Workpiece and Work Area Set Up 1. Designate a work area that is clean and well-lit. The work area must not allow access by children or pets to prevent distraction and injury. 2. Route the power cord along a safe route to reach the work area without creating a tripping hazard or exposing the - Harbor Freight Tools 62520 | User Manual - Page 11
General Operating Instructions 1. Bring the drill bit down with the Feed Handle to where the hole is to be drilled. Make minor workpiece alignment adjustments. 2. Plug the Power - Harbor Freight Tools 62520 | User Manual - Page 12
Servicing Procedures not specifically explained in this manual . If abnormal noise or vibration occurs, have the problem corrected before further use. Cleaning, Maintenance, and Lubrication 2. Replace V-Belt if damaged, following the instructions under Changing Drill Speed on page 9. SETUP - Harbor Freight Tools 62520 | User Manual - Page 13
SAFETY Troubleshooting Problem Possible Causes Tool will not start. 1. Cord not connected. 2. No power loads. 3. Turn off tool and allow to cool. Press reset button on tool. 4. Have technician service tool. Eliminate use of extension cord. If an extension cord is needed, use one with the proper - Harbor Freight Tools 62520 | User Manual - Page 14
DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR 48 Lamp Switch 49 Nut M8 50 Set Screw 51 Pivot Lever 52 Table Support 53 Angle Scale 54 Table 55 $QJOH%ROW0[ 56 Pointer 57A Adjustment Nut - Harbor Freight Tools 62520 | User Manual - Page 15
SAFETY SETUP Assembly Diagram 27 28 23 29 23 26 25 60 33 32 31 30 24 61 23 62 22 16 56 35 34 21 63 57B 36 17 64 57A 40 36 37 20 19 3 15 65 58 38 18 64 66 59 46 45 44 43 42 41 39 13 47 48 12 14 49 50 11 9 10 8 67 7 51 68 54 53 52 69 55 6 70 5 68 4 - Harbor Freight Tools 62520 | User Manual - Page 16
Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
 |
 |
Visit our website at: http://www.harborfreight.com
Email our technical support at: [email protected]
Owner’s Manual & Safety Instructions
Save This Manual
Keep this manual for the safety warnings and precautions, assembly,
operating, inspection, maintenance and cleaning procedures.
Write the product’s serial number in the
back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference.
When unpacking, make sure that the product is intact
and undamaged.
If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
Copyright
©
2015 by Harbor Freight Tools
®
.
All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally.
Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
REV 17a