Harbor Freight Tools 63022 User Manual

Harbor Freight Tools 63022 - 2 HP Gasoline Auger Powerhead Manual

Get Harbor Freight Tools 63022 - 2 HP Gasoline Auger Powerhead PDF manuals and user guides View all Harbor Freight Tools 63022 manuals
Add to My Manuals
Save this manual to your list of manuals

Harbor Freight Tools 63022 manual content summary:

  • Harbor Freight Tools 63022 | User Manual - Page 1
    Manual & Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product's serial number in the back of the manual Tools required for assembly and service may not be included.
  • Harbor Freight Tools 63022 | User Manual - Page 2
    Specifications 2 Safety 3 Setup 7 Operationr 9 Maintenances 12 Troubleshooting 16 Warranties 18 Parts Lists and Diagrams 20 Specifications Maximum warranty information, refer to the last pages of this manual. Page 2 For technical questions, please call 1-888-866-5797. ITEM 63022
  • Harbor Freight Tools 63022 | User Manual - Page 3
    WARNING! Read all instructions. Failure to follow all instructions listed below may result in fire, serious injury and/or DEATH. The warnings and precautions discussed in this manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator
  • Harbor Freight Tools 63022 | User Manual - Page 4
    Safety Setup Operating Precautions 1. Buried utility lines may be unmarked; contact utility companies before drilling. Contacting utility lines may cause severe personal injury or death. 2. Check for landscape fabric before drilling. Landscape fabric may get pulled into the Bit and also pull the
  • Harbor Freight Tools 63022 | User Manual - Page 5
    etc., in accordance with these instructions and in the manner intended for . If damaged, have the Auger serviced before using. Many accidents are caused medical check-ups to ensure medical problems are not being caused or the tool as explained in this manual. If any abnormal vibration occurs,
  • Harbor Freight Tools 63022 | User Manual - Page 6
    of the Auger is maintained. Do not attempt any service or maintenance procedures not explained in this manual or any procedures that you are uncertain about your ability hangs in the air. SAVE THESE INSTRUCTIONS. Setup Operation Maintenance Page 6 For technical questions, please call 1-888-866-5797.
  • Harbor Freight Tools 63022 | User Manual - Page 7
    system for this Engine is warranted for standards set by the U.S. Environmental Protection Agency. For warranty information, refer to the last pages of this manual. IMPORTANT! Your Warranty is voided if either: 1. You operate the Auger without the proper 25:1 fuel/oil mix in its Fuel Tank. Do not
  • Harbor Freight Tools 63022 | User Manual - Page 8
    Safety Components and Controls Starter Handle Handle Power Switch Fuel Tank Throttle Choke Bit Setup Operation Maintenance Page 8 For technical questions, please call 1-888-866-5797. ITEM 63022
  • Harbor Freight Tools 63022 | User Manual - Page 9
    at the beginning of this manual including all text under subheadings therein before set up or use of this product. Safety Setup Operation Pre-Start Checks Inspect engine and Auger looking for damaged, loose, and missing parts before set up and starting. If any problems are found, do not use
  • Harbor Freight Tools 63022 | User Manual - Page 10
    Safety Setup Starting the Engine Before Starting the Engine Before starting the engine: a. Follow the Pre-start Checks to prepare the Auger. b. Inspect the Auger and engine. c. Fill the engine with the proper amount and type of unleaded gasoline and 2-cycle oil mixture. d. Check the work area
  • Harbor Freight Tools 63022 | User Manual - Page 11
    , immediately discontinue using the Auger and contact a qualified service technician to adjust the Auger. 6. Once the Engine full throttle the entire time you are drilling, unless a problem arises. 10. Do not drill at an angle. Keep storage instructions. Setup Operation Maintenance ITEM 63022 For technical questions,
  • Harbor Freight Tools 63022 | User Manual - Page 12
    : Do not use damaged Auger. If abnormal noise, vibration, or excess smoking occurs, have the problem corrected before further use. Follow all service instructions in this manual. The engine may fail critically if not serviced properly. Many maintenance procedures, including any not detailed in this
  • Harbor Freight Tools 63022 | User Manual - Page 13
    Safety Setup Daily Maintenance 1. Before each use: Inspect the general condition of the Auger. Check for misalignment or binding of moving parts, cracked or broken parts, dull, bent, or damaged Bit, and any other condition that may affect the safe operation of the tool. 2. A Bit that is bent or
  • Harbor Freight Tools 63022 | User Manual - Page 14
    Safety Spark plug Maintenance 1. Disconnect spark plug wire from end of plug. Clean out debris from around spark plug. 2. Using a spark plug wrench, remove the spark plug. 3. Inspect the spark plug: If the electrode is oily, clean it using a clean, dry rag. If the electrode has deposits on it,
  • Harbor Freight Tools 63022 | User Manual - Page 15
    Safety Long-Term Storage When the Auger is to remain idle for longer than 20 days, prepare the Engine for storage as follows: 1. CLEANING: Wait for Engine to cool, then clean Engine with dry cloth. NOTICE: Do not clean using water. The water will gradually enter the Engine and cause rust damage.
  • Harbor Freight Tools 63022 | User Manual - Page 16
    Safety Setup Troubleshooting Problem Engine will not start Auger rotates while Engine is gearbox to completely cool. Discontinue using Auger until the gearbox is repaired by a qualified service technician. Faulty Power switch. Immediately remove spark plug cap from spark plug to stop Engine
  • Harbor Freight Tools 63022 | User Manual - Page 17
    spark timing, deposit buildup, worn engine, or other mechanical problems. 1. Impure or low quality gasoline/oil mixture. 2. Engine , E20, E85, etc.). 2. Test/replace fuel tank cap. 3. Have qualified technician service magneto. 4. Secure spark plug cap. 1. Clean element. 2. Allow engine to warm up
  • Harbor Freight Tools 63022 | User Manual - Page 18
    any emissions-related part on your engine if it becomes defective, malfunctions, or otherwise fails to conform with this warranty under normal use and service during the two (2) year term of this warranty at no cost to you, including diagnosis, parts and labor. This warranty applies to the original
  • Harbor Freight Tools 63022 | User Manual - Page 19
    This warranty does not cover normal maintenance services or replacement of maintenance items such as filters to follow the fuel use instructions contained in this manual), neglect, improper maintenance, or to the retail store or contacting product support, you must indicate the specific emissions
  • Harbor Freight Tools 63022 | User Manual - Page 20
    Safety Setup Parts Lists and Diagrams Engine Parts List Part Description 1 Set Screw (M5 X 12) 2 Washer 3 Reel 4 Starter Rope 5 Spiral Spring 6 Recoil Starter Assy. 7 Starter Handle 8 Screw (M5 X 20) 9 Crankcase Gasket 10 Pulley 11 Oil Seal 12 Crankcase Cover 13 Crankcase Gasket 14
  • Harbor Freight Tools 63022 | User Manual - Page 21
    Engine Assembly Diagram ITEM 63022 For technical questions, please call 1-888-866-5797. 66 65 49 48 47 46 45 41 44 40 43 42 26 25 24 50 51 52 54 53 64 63 62 61 58 60 59 57 56 39 38 36 35 37 20 21 19 16 17 18 23 22 7 21 3 4 5 6 8 12 11 15 14 13 30 31 27 28 29 73 10 9 71 72 70
  • Harbor Freight Tools 63022 | User Manual - Page 22
    Safety Auger Parts List Part Description 1A Hub Starter 2A Jump Ring 3A Side Cover 4A Bearing 5A Jump Ring 6A Gear 7A Worm Gear 8A Bearing 9A Jump Ring 10A Gear 11A Jump Ring 12A Gear 13A Bearing 14A Jump Ring 15A Bearing 16A Gear Box 17A Screw Qty. 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
  • Harbor Freight Tools 63022 | User Manual - Page 23
    Safety Setup Auger Diagram 25a 24a 23a 22a 21a 11a 12a 13a 14a 16a 17a 18a 19a 20a 15a 8a 9a 10a 1a 2a 3a 4a 5a 28a 6a 7a 26a 27a 33a 29a 30a 31a 32a Operation Maintenance ITEM 63022 For technical questions, please call 1-888-866-5797. Page 23
  • Harbor Freight Tools 63022 | User Manual - Page 24
    3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • 1-888-866-5797
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
Visit our website at: http://www.harborfreight.com
Email our technical support at: [email protected]
Email our engine support at: [email protected]
Using an engine indoors
CAN KILL YOU IN MINUTES.
Engine exhaust contains carbon monoxide.
This is a poison you cannot see or smell.
NEVER use inside
a home or garage,
EVEN IF doors and
windows are open.
Only use OUTSIDE
and far away from
windows, doors,
and vents.
Owner’s Manual & Safety Instructions
Save This Manual
Keep this manual for the safety warnings and precautions, assembly,
operating, inspection, maintenance and cleaning procedures.
Write the product’s serial number in the
back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference.
When unpacking, make sure that the product is intact
and undamaged.
If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
Copyright
©
2015 by Harbor Freight Tools
®
.
All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally.
Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
REV 16d