Home » Harbor Freight Tools Manuals » Tools » Harbor Freight Tools 63471 » Manual Viewer

Harbor Freight Tools 63471 User Manual

Harbor Freight Tools 63471 - 10 in. 12 Speed Bench Drill Press Manual

View all Harbor Freight Tools 63471 manuals

Add to My Manuals
Save this manual to your list of manuals

Harbor Freight Tools 63471 manual content summary:

Harbor Freight Tools 63471 | User Manual - Page 1
manual and the receipt in a safe and dry place for future reference. 17f Visit our website at: http://www.harborfreight.com Email our technical support slightly from the product described herein. Tools required for assembly and service may not be included. Read this material before using this
Harbor Freight Tools 63471 | User Manual - Page 2
SAFETy Table of contents Important Safety Information 2 Specifications 5 Setup - Before Use 5 Operating Instructions 8 Maintenance and Servicing 12 Parts List and Diagram 14 Warranty 16 WARNING SyMBOLS AND DEFINITIONS This is the safety alert symbol. It is used to alert you to
Harbor Freight Tools 63471 | User Manual - Page 3
servicing; when changing accessories, such as blades, bits, cutters, and the like. 16. REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure switch is in off position before plugging in. 17. USE RECOMMENDED ACCESSORIES. Consult the owner's manual or service personnel if the grounding instructions are
Harbor Freight Tools 63471 | User Manual - Page 4
to a different outlet. Drill press Safety Warnings For your Own Safety Read Instruction Manual Before Operating Drill press 1. Wear eye protection. 2. Do not wear may result in a risk of injury to persons. 8. When servicing use only identical replacement parts. 9. Only use safety equipment that
Harbor Freight Tools 63471 | User Manual - Page 5
have regular medical check-ups to ensure medical problems are not being caused or worsened from use. manual. If any abnormal vibration occurs, stop use immediately. SAVE THESE INSTRUcTIONS. near the end of this manual. Mounting Secure the tool to a supporting structure before use. Before assembly
Harbor Freight Tools 63471 | User Manual - Page 6
(7). Tighten the Set Screw (17), but do not overtighten it. 4. Slide the Height Crank (23) over the Shaft (24) on the side of the Table Support (21). Secure it to the Shaft using the Screw (22) against the flat part of the Shaft. Screw (22) Height crank (23) Figure D: Installing Height
Harbor Freight Tools 63471 | User Manual - Page 7
SAFETy SETUp Headstock to column 1. Loosen the two Set Screws (17) on the left side of the Headstock (67) so they will stay clear while installing it. 2. With the help of an assistant, lift the Headstock above the Column (6), and gently slide it down the Column as far as it will go. 3. Tighten the
Harbor Freight Tools 63471 | User Manual - Page 8
SAFETy SETUp Operating Instructions Read the ENTIRE IMpORTANT SAFETy INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Tool Set Up TO pREVENT SERIOUS INJURy FROM AccIDENTAL OpERATION: Turn
Harbor Freight Tools 63471 | User Manual - Page 9
SAFETy SETUp changing Drill Speed Before changing the speeds, make sure the machine is switched OFF and UNPLUGGED. 1. Open the pulley cover. 2. Loosen the Motor Tension Knob (70) on each side of the Headstock (67), and move the Motor (77) towards the Headstock to relieve tension on the Belts (
Harbor Freight Tools 63471 | User Manual - Page 10
SAFETy Workpiece and Work Area Set Up 1. Designate a work area that is clean and well-lit. The work area must not allow access by children or pets to prevent distraction and injury. 9. FOR SMALL MATERIALS that cannot be clamped to the table, use a drill press vise. Make sure the vise is clamped
Harbor Freight Tools 63471 | User Manual - Page 11
General Operating Instructions 1. Bring the drill bit down with the Feed Knob to where the hole is to be drilled. Make minor workpiece alignment adjustments. 2. Plug the Power
Harbor Freight Tools 63471 | User Manual - Page 12
Servicing procedures not specifically explained in this manual . If abnormal noise or vibration occurs, have the problem corrected before further use. cleaning, Maintenance, and Lubrication . 2. Replace belt if damaged, following the instructions under Changing Drill Speed on page 9. SETUp
Harbor Freight Tools 63471 | User Manual - Page 13
SAFETy Troubleshooting problem possible causes Likely Solutions Tool will not start. 1. Cord not to cool. Press reset button on tool. 4. Internal damage or wear. (Carbon 4. Have technician service tool. brushes or switch, for example.) Tool operates slowly. Extension cord too long or wire
Harbor Freight Tools 63471 | User Manual - Page 14
/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY Screw 67 Headstock 68 Depth Pointer 69 Round Pin 70 Knob 71 Motor Support 72 Flat Washer 10 73 Bolt M8×20 74 Motor Bracket 75 Spring
Harbor Freight Tools 63471 | User Manual - Page 15
Assembly Diagram SAFETy SETUp OpERATION MAINTENANcE Record product's Serial Number Here: Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement
Harbor Freight Tools 63471 | User Manual - Page 16
Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.