Harbor Freight Tools 68827 User Manual

Harbor Freight Tools 68827 - 10 in., 13 Amp Industrial Table Saw Manual

Get Harbor Freight Tools 68827 - 10 in., 13 Amp Industrial Table Saw PDF manuals and user guides View all Harbor Freight Tools 68827 manuals
Add to My Manuals
Save this manual to your list of manuals

Harbor Freight Tools 68827 manual content summary:

  • Harbor Freight Tools 68827 | User Manual - Page 1
  • Harbor Freight Tools 68827 | User Manual - Page 2
    injury. Addresses practices not related to personal injury. IMPORTANT SAFETy INFORMATION General Tool Safety Warnings WARNING Read all safety warnings and instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and
  • Harbor Freight Tools 68827 | User Manual - Page 3
    operate tool. 14. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories. 15. DISCONNECT TOOLS before servicing; when changing accessories, such as blades, bits, cutters, and the like. 16. REDUCE THE RISK OF
  • Harbor Freight Tools 68827 | User Manual - Page 4
    qualified electrician or service personnel if the grounding instructions are not completely Warnings For your Own Safety Read Instruction Manual Before Operating Saw 1. Wear eye a workpiece through the saw without using a fence or guided support to guide it. NOT A SAFE METHOD. g. Kerf - The
  • Harbor Freight Tools 68827 | User Manual - Page 5
    (such as nails and screws). • Support large workpieces along their entire length. guide when crosscutting. • Do not ripcut a twisted or warped workpiece, or workpiece without straight edge to guide instructions discussed in this instruction manual ups to ensure medical problems are not being caused
  • Harbor Freight Tools 68827 | User Manual - Page 6
    SAFETy Handle Notch • Must be far enough down the stick to allow a comfortable and firm grip. • Must be deep enough to prevent hand from slipping down the stick. • Do not cut more than halfway into the stick to prevent weakening. • Corners may be rounded to increase comfort. Essential Straight
  • Harbor Freight Tools 68827 | User Manual - Page 7
    refer to the Assembly Diagram near the end of this manual. Mounting Table Saw If mounting onto a metal table stand: 1. Select a table stand which will support the weight of the Table Saw. Follow the table saw stand instructions for assembly. Tighten all connections, making sure the assembled table
  • Harbor Freight Tools 68827 | User Manual - Page 8
    SAFETy SETUP Specifications Electrical Rating 120V~ / 60Hz / 13A Motor No Load Speed 5,000 RPM Max. Depth Cut 3" @ 90° 2-1/2" @ 45° Max. Dado Cut 1/2" Wide Arbor 5/8" 230181 Functions Table (133) Push Stick (187) Miter Gauge (179) Anti-Kickback Pawls (67, 72) Blade Guard Fence (
  • Harbor Freight Tools 68827 | User Manual - Page 9
    SAFETy SETUP Installing/changing Blade TO PREVENT SERIOUS INJURy: Before installing a saw blade, unplug the Table Saw and wear heavy-duty work gloves. Be very careful during blade tightening and loosening to avoid contact with the blade. 4. Turn the Lock Knob (100) counterclockwise to loosen the
  • Harbor Freight Tools 68827 | User Manual - Page 10
    Adjusting Riving Knife TO PREVENT SERIOUS INJURy: Unplug the Table Saw before this procedure. NOTE: The Riving Knife (45) follows the saw blade to keep the kerf (gap) from closing on the saw blade. Reposition the Riving Knife before initial use. Riving Knife (45) Riving Knife (45) SAFETy SETUP
  • Harbor Freight Tools 68827 | User Manual - Page 11
    SAFETy SETUP Attaching Blade Guard Riving Knife (45) TO PREVENT SERIOUS INJURy: Unplug the Table Saw before this procedure. BLADE GUARD MUST BE INSTALLED BEFORE USE. Guard Locking Lever (75) Blade Guard 1. Set the Blade Guard against the top of the Riving Knife so that the Rollers (76, 86)
  • Harbor Freight Tools 68827 | User Manual - Page 12
    SAFETy SETUP Operating Instructions Read the ENTIRE IMPORTANT SAFETy INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. TOOL SET UP TO PREVENT SERIOUS INJURy FROM AccIDENTAL OPERATION: Turn
  • Harbor Freight Tools 68827 | User Manual - Page 13
    Width Of cut Fence (194) Fence Handle (203) Graduated Scale Guide (196) Figure S WARNING! Do not attempt to use the the workpiece and Fence together to the right or left until the left side of the Guide (196) aligns with the desired measurement on the Graduated Scale. c. Lock the Fence in
  • Harbor Freight Tools 68827 | User Manual - Page 14
    INSTRUcTIONS Pushstick or make a push-stick as described in the Safety section of this manual. Use a Push-block (not included) when ripping widths under 2". Miter After the cut is under way, use the Push-stick to continue guiding the workpiece forward. Just before the cut is completed, move the left
  • Harbor Freight Tools 68827 | User Manual - Page 15
    again in the usual manner. Maintenance and Servicing Procedures not specifically explained in this manual must be performed only by a qualified damaged equipment. If abnormal noise or vibration occurs, have the problem corrected before further use. cleaning, Maintenance, and Lubrication 1. BEFORE
  • Harbor Freight Tools 68827 | User Manual - Page 16
    SAFETy SETUP Troubleshooting Problem Motor will not start. Possible causes 1. Low voltage. 2. and steel wool. Follow all safety precautions whenever diagnosing or servicing the tool. Disconnect power supply before service. OPERATION MAINTENANcE Page 16 For technical questions, please call
  • Harbor Freight Tools 68827 | User Manual - Page 17
    SAFETy Troubleshooting (cont.) Problem Workpiece kicked back from blade. Possible causes 1. Fence out of alignment. service. SETUP OPERATION MAINTENANcE PLEASE READ THE FOLLOWING cAREFULLy THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL
  • Harbor Freight Tools 68827 | User Manual - Page 18
    Sleeve Axis Rear Left Guard Knife Link Pin Hex Nut Hex Nut Bracket Nut Washer Support Board Bolt Lock Knob Hex Bolt Board Washer Large Washer Bracket Wave Washer Bolt Sleeve Wrench Screw Rear Plate Spring Rear Cover Fence Bolt Guide Bolt Angle Pointer Adjusting Nut Cam Pin Pin Fence Handle Pin Fence Assembly Qty
  • Harbor Freight Tools 68827 | User Manual - Page 19
    Assembly Diagram SAFETy SETUP OPERATION MAINTENANcE Item 68827 For technical questions, please call 1-888-866-5797. Page 19
  • Harbor Freight Tools 68827 | User Manual - Page 20
    Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20