Hayward 90 Sq.Ft. Star-Clear Plus Filter Omni-Controls-VSP-Communication-Board
Hayward 90 Sq.Ft. Star-Clear Plus Filter Manual
 |
View all Hayward 90 Sq.Ft. Star-Clear Plus Filter manuals
Add to My Manuals
Save this manual to your list of manuals |
Hayward 90 Sq.Ft. Star-Clear Plus Filter manual content summary:
- Hayward 90 Sq.Ft. Star-Clear Plus Filter | Omni-Controls-VSP-Communication-Board - Page 1
092757 RevA Omni Controls VSP Communication Board for Omni Controls Installation Manual Contents Overview 1 Installation 1 Operation 5 HLPMPCONV Hayward Industries 400 Connell Drive, Suite 6100 Berkeley Heights, NJ 07922 Phone: (908) 355-7995 www.hayward.com USE ONLY - Hayward 90 Sq.Ft. Star-Clear Plus Filter | Omni-Controls-VSP-Communication-Board - Page 2
Install and setup the pump for remote control according to its included instructions. Install and wire the HLPMPCONV according to the instructions in this manual. After installation is complete, your Omni Control manual will explain how to configure and control the pump. IMPORTANT: Before attempting - Hayward 90 Sq.Ft. Star-Clear Plus Filter | Omni-Controls-VSP-Communication-Board - Page 3
From Omni Control From Pentair Pump(s) Green White Black Red Green Yellow Electrical Wire Nuts VSP 1 VSP 2 VSP 3 Use a jumper for systems with 3 pumps 12 AWG Wire to RS485 Connector 2 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS - Hayward 90 Sq.Ft. Star-Clear Plus Filter | Omni-Controls-VSP-Communication-Board - Page 4
Installing HLPMPCONV into the Enclosure After wiring is complete, insert the HLPMPCONV into the enclosure as shown. 3 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS - Hayward 90 Sq.Ft. Star-Clear Plus Filter | Omni-Controls-VSP-Communication-Board - Page 5
Routing wires through the wiring channel Route the cables through the wiring channel and out the exit of the enclosure. Sandwich the cables at the exit point using one of the two tear out foam strips that are attached to the cover gasket. At the exit, lay the cables in the center of the strip and - Hayward 90 Sq.Ft. Star-Clear Plus Filter | Omni-Controls-VSP-Communication-Board - Page 6
HLPMPCONV. To ensure proper support, update to the latest firmware version by going to https://www.hayward.com/firmware and downloading the latest Omni Control firmware files. Refer to the Release Notes on that page for upgrade instructions. After the update is complete, the pump can be configured - Hayward 90 Sq.Ft. Star-Clear Plus Filter | Omni-Controls-VSP-Communication-Board - Page 7
6 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS - Hayward 90 Sq.Ft. Star-Clear Plus Filter | Omni-Controls-VSP-Communication-Board - Page 8
For further information or consumer technical support, visit our website at www.hayward.com Hayward is a registered trademark of Hayward Industries, Inc. © 2020 Hayward Industries, Inc. All other trademarks not owned by
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
 |
 |
Hayward Industries
400 Connell Drive, Suite 6100
Berkeley Heights, NJ 07922
Phone: (908) 355-7995
www.hayward.com
Omni Controls
VSP Communication Board for Omni Controls
Installation Manual
HLPMPCONV
Contents
Overview
................................
1
Installation
.............................
1
Operation
..............................
5
092757 RevA
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS