HP 3PAR StoreServ 7200 2-node HP 3PAR StoreServ 7000/7450 Storage Cabling Conf
HP 3PAR StoreServ 7200 2-node Manual
View all HP 3PAR StoreServ 7200 2-node manuals
Add to My Manuals
Save this manual to your list of manuals |
HP 3PAR StoreServ 7200 2-node manual content summary:
- HP 3PAR StoreServ 7200 2-node | HP 3PAR StoreServ 7000/7450 Storage Cabling Conf - Page 1
HP 3PAR StoreServ 7000/7450 Storage Cabling Configuration Guide E: 4 Node Systems with Large 3.5-inch Drive Enclosures Abstract This guide provides cabling information for authorized technicians performing installation and maintenance services on the HP 3PAR StoreServ 7000/7450 Storage systems. HP - HP 3PAR StoreServ 7200 2-node | HP 3PAR StoreServ 7000/7450 Storage Cabling Conf - Page 2
© Copyright 2013 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be - HP 3PAR StoreServ 7200 2-node | HP 3PAR StoreServ 7000/7450 Storage Cabling Conf - Page 3
Following Precautions...5 Identifying and Labeling the Components 5 2 Cabling HP 3PAR StoreServ 7000/7450 8 4 Node 2 Drive Enclosures (2L 8 Attach DP-1 Chains to Enclosure 9 Attach DP-2 Chains to Enclosures 10 Review Completed Cabling 11 4 Node 4 Drive Enclosures (4L 12 Attach DP-1 Chains to - HP 3PAR StoreServ 7200 2-node | HP 3PAR StoreServ 7000/7450 Storage Cabling Conf - Page 4
HP 3PAR Documentation...52 4 Contents - HP 3PAR StoreServ 7200 2-node | HP 3PAR StoreServ 7000/7450 Storage Cabling Conf - Page 5
all configurations in this guide. The guide provides instructional guidance for cabling the HP 3PAR StoreServ 7000/7450 according to a specific configuration. All HP 3PAR StoreServ Storage systems contain either the HP 3PAR 7200 (2 nodes) or 7400/7450 (with 2 or 4 nodes), M6720 large drive enclosure - HP 3PAR StoreServ 7200 2-node | HP 3PAR StoreServ 7000/7450 Storage Cabling Conf - Page 6
Types of Components Use the red and green color coding to assist with the cabling. Only connect to components sharing the same color. Figure 1 Identifying Components and SAS Ports 6 Cabling Preparation for HP 3PAR StoreServ 7000/7450 - HP 3PAR StoreServ 7200 2-node | HP 3PAR StoreServ 7000/7450 Storage Cabling Conf - Page 7
in the storage system. Apply the labels to each enclosure in a visible location and avoid covering other labels • Apply label A to the controller enclosure with nodes 0 and relating to cabling hosts, refer to HP 3PAR StoreServ 7000/7450 Installation Guide. Identifying and Labeling the Components 7 - HP 3PAR StoreServ 7200 2-node | HP 3PAR StoreServ 7000/7450 Storage Cabling Conf - Page 8
rack with recommended racking configuration of the system. 4 Node 2 Drive Enclosures (2L) Before you begin cabling the storage system, carefully read or print the following section, including figures 1 and 2 "Identifying and Labeling the Components" (page 5). 8 Cabling HP 3PAR StoreServ 7000/7450 - HP 3PAR StoreServ 7200 2-node | HP 3PAR StoreServ 7000/7450 Storage Cabling Conf - Page 9
Attach DP-1 Chains to Enclosure This system does not require any connections to node port DP-1. 4 Node 2 Drive Enclosures (2L) 9 - HP 3PAR StoreServ 7200 2-node | HP 3PAR StoreServ 7000/7450 Storage Cabling Conf - Page 10
the controller. 3. Connect Node 3 (DP-2) to I/O 1 (DP-1) on the D drive enclosure farthest from the controller. 4. Connect all D drive enclosures from (DP-2) to (DP-1) working toward the controller. NOTE: The two adjacent enclosures are not directly connected. 10 Cabling HP 3PAR StoreServ 7000/7450 - HP 3PAR StoreServ 7200 2-node | HP 3PAR StoreServ 7000/7450 Storage Cabling Conf - Page 11
Review Completed Cabling 4 Node 2 Drive Enclosures (2L) 11 - HP 3PAR StoreServ 7200 2-node | HP 3PAR StoreServ 7000/7450 Storage Cabling Conf - Page 12
4 Node 4 Drive Enclosures (4L) Before you begin cabling the storage system, carefully read or print the following section, including figures 1 and 2 "Identifying and Labeling the Components" (page 5). 12 Cabling HP 3PAR StoreServ 7000/7450 - HP 3PAR StoreServ 7200 2-node | HP 3PAR StoreServ 7000/7450 Storage Cabling Conf - Page 13
the A drive enclosure closest to the controller. 2. Connect all A drive enclosures from (DP-2) to (DP-1) working away from the controller. 3. Connect Node 2 (DP-1) to the I/O 0 (DP-1) on the C drive enclosure closest to the controller. 4. Connect all C drive enclosures from (DP-2) to (DP-1) working - HP 3PAR StoreServ 7200 2-node | HP 3PAR StoreServ 7000/7450 Storage Cabling Conf - Page 14
the controller. 3. Connect Node 3 (DP-2) to I/O 1 (DP-1) on the D drive enclosure farthest from the controller. 4. Connect all D drive enclosures from (DP-2) to (DP-1) working toward the controller. NOTE: The two adjacent enclosures are not directly connected. 14 Cabling HP 3PAR StoreServ 7000/7450 - HP 3PAR StoreServ 7200 2-node | HP 3PAR StoreServ 7000/7450 Storage Cabling Conf - Page 15
Review Completed Cabling 4 Node 4 Drive Enclosures (4L) 15 - HP 3PAR StoreServ 7200 2-node | HP 3PAR StoreServ 7000/7450 Storage Cabling Conf - Page 16
4 Node 6 Drive Enclosures (6L) Before you begin cabling the storage system, carefully read or print the following section, including figures 1 and 2 "Identifying and Labeling the Components" (page 5). 16 Cabling HP 3PAR StoreServ 7000/7450 - HP 3PAR StoreServ 7200 2-node | HP 3PAR StoreServ 7000/7450 Storage Cabling Conf - Page 17
the A drive enclosure closest to the controller. 2. Connect all A drive enclosures from (DP-2) to (DP-1) working away from the controller. 3. Connect Node 2 (DP-1) to the I/O 0 (DP-1) on the C drive enclosure closest to the controller. 4. Connect all C drive enclosures from (DP-2) to (DP-1) working - HP 3PAR StoreServ 7200 2-node | HP 3PAR StoreServ 7000/7450 Storage Cabling Conf - Page 18
the controller. 3. Connect Node 3 (DP-2) to I/O 1 (DP-1) on the D drive enclosure farthest from the controller. 4. Connect all D drive enclosures from (DP-2) to (DP-1) working toward the controller. NOTE: The two adjacent enclosures are not directly connected. 18 Cabling HP 3PAR StoreServ 7000/7450 - HP 3PAR StoreServ 7200 2-node | HP 3PAR StoreServ 7000/7450 Storage Cabling Conf - Page 19
Review Completed Cabling 4 Node 6 Drive Enclosures (6L) 19 - HP 3PAR StoreServ 7200 2-node | HP 3PAR StoreServ 7000/7450 Storage Cabling Conf - Page 20
Node 2, Intr 0 The completed cabling is shown below. After confirming all cabling is correct (SAS and interconnection), the system may be powered on by using procedures from the installation guide. NOTE: The Interconnect Link Cables are directional and labeled A and C. 20 Cabling HP 3PAR StoreServ - HP 3PAR StoreServ 7200 2-node | HP 3PAR StoreServ 7000/7450 Storage Cabling Conf - Page 21
4 Node 8 Drive Enclosures (8L) Before you begin cabling the storage system, carefully read or print the following section, including figures 1 and 2 "Identifying and Labeling the Components" (page 5). 4 Node 8 Drive Enclosures (8L) 21 - HP 3PAR StoreServ 7200 2-node | HP 3PAR StoreServ 7000/7450 Storage Cabling Conf - Page 22
the controller. 3. Connect Node 3 (DP-1) to I/O 1 (DP-1) on the C drive enclosure farthest from the controller. 4. Connect all C drive enclosures from (DP-2) to (DP-1) working toward the controller. NOTE: The two adjacent enclosures are not directly connected. 22 Cabling HP 3PAR StoreServ 7000/7450 - HP 3PAR StoreServ 7200 2-node | HP 3PAR StoreServ 7000/7450 Storage Cabling Conf - Page 23
the B drive enclosure closest to the controller. 2. Connect all B drive enclosures from (DP-2) to (DP-1) working away from the controller. 3. Connect Node 2 (DP-2) to the I/O 0 (DP-1) on the D drive enclosure closest to the controller. 4. Connect all D drive enclosures from (DP-2) to (DP-1) working - HP 3PAR StoreServ 7200 2-node | HP 3PAR StoreServ 7000/7450 Storage Cabling Conf - Page 24
Review Completed Cabling 24 Cabling HP 3PAR StoreServ 7000/7450 - HP 3PAR StoreServ 7200 2-node | HP 3PAR StoreServ 7000/7450 Storage Cabling Conf - Page 25
Intr 0 to Controller C, Node 3, Intr 1 4. Controller A, Node 1, Intr 1 to Controller C, Node 2, Intr 0 The completed cabling is shown below. After confirming all cabling is correct (SAS and interconnection), the system may be powered on by using procedures from the installation guide. CAUTION: The - HP 3PAR StoreServ 7200 2-node | HP 3PAR StoreServ 7000/7450 Storage Cabling Conf - Page 26
4 Node 12 Drive Enclosures (12L) Before you begin cabling the storage system, carefully read or print the following section, including figures 1 and 2 "Identifying and Labeling the Components" (page 5). 26 Cabling HP 3PAR StoreServ 7000/7450 - HP 3PAR StoreServ 7200 2-node | HP 3PAR StoreServ 7000/7450 Storage Cabling Conf - Page 27
enclosure closest to the controller. 2. Connect all C drive enclosures from (DP-2) to (DP-1) working away from the controller. Green routing 1. Connect Node 3 (DP-1) to I/O 1 (DP-1) on the C drive enclosure farthest from the controller. 2. Connect all C drive enclosures from (DP-2) to (DP-1) working - HP 3PAR StoreServ 7200 2-node | HP 3PAR StoreServ 7000/7450 Storage Cabling Conf - Page 28
. Green routing 1. Connect Node 3 (DP-2) to I/O 1 (DP-1) on the D drive enclosure farthest from the controller. 2. Connect all D drive enclosures from (DP-2) to (DP-1) working toward the controller. NOTE: The two adjacent enclosures are not directly connected. 28 Cabling HP 3PAR StoreServ 7000/7450 - HP 3PAR StoreServ 7200 2-node | HP 3PAR StoreServ 7000/7450 Storage Cabling Conf - Page 29
Review Completed Cabling 4 Node 12 Drive Enclosures (12L) 29 - HP 3PAR StoreServ 7200 2-node | HP 3PAR StoreServ 7000/7450 Storage Cabling Conf - Page 30
cabling is shown below. After confirming all cabling is correct (SAS and interconnection), the system may be powered on by using procedures from the installation guide. CAUTION: The Interconnect Link Cables are directional and labeled A and C. 30 Cabling HP 3PAR StoreServ 7000/7450 - HP 3PAR StoreServ 7200 2-node | HP 3PAR StoreServ 7000/7450 Storage Cabling Conf - Page 31
4 Node 14 Drive Enclosures (14L) Before you begin cabling the storage system, carefully read or print the following section, including figures 1 and 2 "Identifying and Labeling the Components" (page 5). 4 Node 14 Drive Enclosures (14L) 31 - HP 3PAR StoreServ 7200 2-node | HP 3PAR StoreServ 7000/7450 Storage Cabling Conf - Page 32
. Green routing 1. Connect Node 3 (DP-1) to I/O 1 (DP-1) on the C drive enclosure farthest from the controller. 2. Connect all C drive enclosures from (DP-2) to (DP-1) working toward the controller. NOTE: The two adjacent enclosures are not directly connected. 32 Cabling HP 3PAR StoreServ 7000/7450 - HP 3PAR StoreServ 7200 2-node | HP 3PAR StoreServ 7000/7450 Storage Cabling Conf - Page 33
enclosure closest to the controller. 2. Connect all D drive enclosures from (DP-2) to (DP-1) working away from the controller. Green routing 1. Connect Node 3 (DP-2) to I/O 1 (DP-1) on the D drive enclosure farthest from the controller. 2. Connect all D drive enclosures from (DP-2) to (DP-1) working - HP 3PAR StoreServ 7200 2-node | HP 3PAR StoreServ 7000/7450 Storage Cabling Conf - Page 34
Review Completed Cabling 34 Cabling HP 3PAR StoreServ 7000/7450 - HP 3PAR StoreServ 7200 2-node | HP 3PAR StoreServ 7000/7450 Storage Cabling Conf - Page 35
Intr 0 to Controller C, Node 3, Intr 1 4. Controller A, Node 1, Intr 1 to Controller C, Node 2, Intr 0 The completed cabling is shown below. After confirming all cabling is correct (SAS and interconnection), the system may be powered on by using procedures from the installation guide. CAUTION: The - HP 3PAR StoreServ 7200 2-node | HP 3PAR StoreServ 7000/7450 Storage Cabling Conf - Page 36
4 Node 16 Drive Enclosures (16L) Before you begin cabling the storage system, carefully read or print the following section, including figures 1 and 2 "Identifying and Labeling the Components" (page 5). 36 Cabling HP 3PAR StoreServ 7000/7450 - HP 3PAR StoreServ 7200 2-node | HP 3PAR StoreServ 7000/7450 Storage Cabling Conf - Page 37
enclosure closest to the controller. 2. Connect all C drive enclosures from (DP-2) to (DP-1) working away from the controller. Green routing 1. Connect Node 3 (DP-1) to I/O 1 (DP-1) on the C drive enclosure farthest from the controller. 2. Connect all C drive enclosures from (DP-2) to (DP-1) working - HP 3PAR StoreServ 7200 2-node | HP 3PAR StoreServ 7000/7450 Storage Cabling Conf - Page 38
. Green routing 1. Connect Node 1 (DP-1) to I/O 1 (DP-1) on the A drive enclosure farthest from the controller. 2. Connect all A drive enclosures from (DP-2) to (DP-1) working toward the controller. NOTE: The two adjacent enclosures are not directly connected. 38 Cabling HP 3PAR StoreServ 7000/7450 - HP 3PAR StoreServ 7200 2-node | HP 3PAR StoreServ 7000/7450 Storage Cabling Conf - Page 39
enclosure closest to the controller. 2. Connect all D drive enclosures from (DP-2) to (DP-1) working away from the controller. Green routing 1. Connect Node 3 (DP-2) to I/O 1 (DP-1) on the D drive enclosure farthest from the controller. 2. Connect all D drive enclosures from (DP-2) to (DP-1) working - HP 3PAR StoreServ 7200 2-node | HP 3PAR StoreServ 7000/7450 Storage Cabling Conf - Page 40
. Green routing 1. Connect Node 1 (DP-2) to I/O 1 (DP-1) on the B drive enclosure farthest from the controller. 2. Connect all B drive enclosures from (DP-2) to (DP-1) working toward the controller. NOTE: The two adjacent enclosures are not directly connected. 40 Cabling HP 3PAR StoreServ 7000/7450 - HP 3PAR StoreServ 7200 2-node | HP 3PAR StoreServ 7000/7450 Storage Cabling Conf - Page 41
Review Completed Cabling 4 Node 16 Drive Enclosures (16L) 41 - HP 3PAR StoreServ 7200 2-node | HP 3PAR StoreServ 7000/7450 Storage Cabling Conf - Page 42
Review Completed Cabling Between Racks 42 Cabling HP 3PAR StoreServ 7000/7450 - HP 3PAR StoreServ 7200 2-node | HP 3PAR StoreServ 7000/7450 Storage Cabling Conf - Page 43
Intr 0 to Controller C, Node 3, Intr 1 4. Controller A, Node 1, Intr 1 to Controller C, Node 2, Intr 0 The completed cabling is shown below. After confirming all cabling is correct (SAS and interconnection), the system may be powered on by using procedures from the installation guide. CAUTION: The - HP 3PAR StoreServ 7200 2-node | HP 3PAR StoreServ 7000/7450 Storage Cabling Conf - Page 44
4 Node 18 Drive Enclosures (18L) Before you begin cabling the storage system, carefully read or print the following section, including figures 1 and 2 "Identifying and Labeling the Components" (page 5). 44 Cabling HP 3PAR StoreServ 7000/7450 - HP 3PAR StoreServ 7200 2-node | HP 3PAR StoreServ 7000/7450 Storage Cabling Conf - Page 45
enclosure closest to the controller. 2. Connect all C drive enclosures from (DP-2) to (DP-1) working away from the controller. Green routing 1. Connect Node 3 (DP-1) to I/O 1 (DP-1) on the C drive enclosure farthest from the controller. 2. Connect all C drive enclosures from (DP-2) to (DP-1) working - HP 3PAR StoreServ 7200 2-node | HP 3PAR StoreServ 7000/7450 Storage Cabling Conf - Page 46
. Green routing 1. Connect Node 1 (DP-1) to I/O 1 (DP-1) on the A drive enclosure farthest from the controller. 2. Connect all A drive enclosures from (DP-2) to (DP-1) working toward the controller. NOTE: The two adjacent enclosures are not directly connected. 46 Cabling HP 3PAR StoreServ 7000/7450 - HP 3PAR StoreServ 7200 2-node | HP 3PAR StoreServ 7000/7450 Storage Cabling Conf - Page 47
enclosure closest to the controller. 2. Connect all D drive enclosures from (DP-2) to (DP-1) working away from the controller. Green routing 1. Connect Node 3 (DP-2) to I/O 1 (DP-1) on the D drive enclosure farthest from the controller. 2. Connect all D drive enclosures from (DP-2) to (DP-1) working - HP 3PAR StoreServ 7200 2-node | HP 3PAR StoreServ 7000/7450 Storage Cabling Conf - Page 48
. Green routing 1. Connect Node 1 (DP-2) to I/O 1 (DP-1) on the B drive enclosure farthest from the controller. 2. Connect all B drive enclosures from (DP-2) to (DP-1) working toward the controller. NOTE: The two adjacent enclosures are not directly connected. 48 Cabling HP 3PAR StoreServ 7000/7450 - HP 3PAR StoreServ 7200 2-node | HP 3PAR StoreServ 7000/7450 Storage Cabling Conf - Page 49
Review Completed Cabling 4 Node 18 Drive Enclosures (18L) 49 - HP 3PAR StoreServ 7200 2-node | HP 3PAR StoreServ 7000/7450 Storage Cabling Conf - Page 50
Review Completed Cabling Between Racks 50 Cabling HP 3PAR StoreServ 7000/7450 - HP 3PAR StoreServ 7200 2-node | HP 3PAR StoreServ 7000/7450 Storage Cabling Conf - Page 51
Intr 0 to Controller C, Node 3, Intr 1 4. Controller A, Node 1, Intr 1 to Controller C, Node 2, Intr 0 The completed cabling is shown below. After confirming all cabling is correct (SAS and interconnection), the system may be powered on by using procedures from the installation guide. CAUTION: The - HP 3PAR StoreServ 7200 2-node | HP 3PAR StoreServ 7000/7450 Storage Cabling Conf - Page 52
3PAR F-Class storage systems Support Request StoreServ 7000/7450 Storage 3PAR or 3PAR Storage HP 3PAR Documentation For additional information about other related cabling configurations, refer to the following documents: • HP 3PAR StoreServ 7000/7450 Storage Cabling Configuration Guide A: 2 Node
HP 3PAR StoreServ 7000/7450 Storage
Cabling Configuration Guide E:
4 Node Systems with Large 3.5-inch Drive
Enclosures
Abstract
This guide provides cabling information for authorized technicians performing installation and maintenance services on the HP
3PAR StoreServ 7000/7450 Storage systems.
HP Part Number: QR482-96454
Published: August 2013
Edition: 1