HP BladeSystem c3000 HP BladeSystem c3000 Enclosure Quick Setup Instructions
HP BladeSystem c3000 Manual
View all HP BladeSystem c3000 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP BladeSystem c3000 manual content summary:
- HP BladeSystem c3000 | HP BladeSystem c3000 Enclosure Quick Setup Instructions - Page 1
HP BladeSystem c3000 Enclosure Quick Setup Instructions Part Number 446990-006 - HP BladeSystem c3000 | HP BladeSystem c3000 Enclosure Quick Setup Instructions - Page 2
2 - HP BladeSystem c3000 | HP BladeSystem c3000 Enclosure Quick Setup Instructions - Page 3
HP BladeSystem c3000 The HP BladeSystem enclosure Enclosure chassis (rear chassis viewed from the rear view) 3 Device bay blank A mandatory insert installed in any unused device bay 4 Power supply blank A mandatory insert installed in any unused power supply bay 5 Power supply The power - HP BladeSystem c3000 | HP BladeSystem c3000 Enclosure Quick Setup Instructions - Page 4
cause damage to pins and connectors. 1. The enclosure can be installed in a rack or rack-free environment. Select the proper location based on requirements detailed in the HP BladeSystem c3000 Enclosure Setup and Installation Guide. 2. With the enclosure still on the pallet, remove all components - HP BladeSystem c3000 | HP BladeSystem c3000 Enclosure Quick Setup Instructions - Page 5
the HP BladeSystem c3000 Enclosure Rack Template. For rack-free installations, omit this step. 4. Install the front cage into the enclosure, then tighten the thumbscrews. Power supply bay numbering Enclosure bay identification Before installing front or rear components into the enclosure, review - HP BladeSystem c3000 | HP BladeSystem c3000 Enclosure Quick Setup Instructions - Page 6
IMPORTANT: The length of HP ProLiant Gen8 server blades is longer than previous generations, and these server blades protrude slightly from the edge of the enclosure. The initial stopping cards 5. Choose one of the following options: o If you are installing a half-height device, omit this step. 6 - HP BladeSystem c3000 | HP BladeSystem c3000 Enclosure Quick Setup Instructions - Page 7
-height device in bays 3/7 and two half-height devices in bays 4/8, install the mini divider. 6. Remove the connector covers. 7. Install the server or storage blades. NOTE: If you plan to install four HP Active Cool 100 Fans, you can install up to two full-height blades or up to four half-height - HP BladeSystem c3000 | HP BladeSystem c3000 Enclosure Quick Setup Instructions - Page 8
or a blank. 1. Slide the fan into the enclosure until it locks in place. NOTE: The HP BladeSystem c3000 Enclosure ships with four HP Active Cool 100 fans and supports up to six fans. Install fans based on the number of storage or server blades installed: • For one to four half-height storage or - HP BladeSystem c3000 | HP BladeSystem c3000 Enclosure Quick Setup Instructions - Page 9
power supply bays 1 and 4 1, 4, and 2 1, 4, 2, and 5 1, 4, 2, 5, and 3 Populate all bays Connecting the cables 1. Identify all connectors. Item Connector Description 1 Enclosure Connects to the enclosure link-up port on the link-down enclosure beneath it with a CAT5 patch cable. port 2 Enclosure - HP BladeSystem c3000 | HP BladeSystem c3000 Enclosure Quick Setup Instructions - Page 10
: The enclosure link ports are designed only to support c-Class enclosures in the same rack. The enclosure link-up port on the top enclosure is the service port, and the enclosure link-down port on the bottom linked enclosure is unused. NOTE: The HP BladeSystem c-Class enclosure link ports are not - HP BladeSystem c3000 | HP BladeSystem c3000 Enclosure Quick Setup Instructions - Page 11
Connection Port number Connects to interconnect bay/port Mezzanine slot 1x/2x port 1 1-1x or 2x cards (4x 1x/2x port 2 cards are not supported in this slot) 2/Port N 2/Port N+8 Mezzanine slot 1x/2x port 1 3/Port N 2-1x or 2x cards 1x/2x port 2 4 Port N 1x/2x port 3 3/Port N+8 1x/2x port - HP BladeSystem c3000 | HP BladeSystem c3000 Enclosure Quick Setup Instructions - Page 12
. To support network connections for specific signals, install an interconnect module in the bay corresponding to the embedded NIC or mezzanine signals. Connection Embedded NIC Mezzanine slot 1-1x, 2x, or 4x cards Port number Connects to interconnect bay/port Server A: NIC 1 1/Port N Server - HP BladeSystem c3000 | HP BladeSystem c3000 Enclosure Quick Setup Instructions - Page 13
Powering up the enclosure 1. Connect the power cables to the power supplies. 2. Connect the power cables to the power source or to an installed PDU. 3. Turn on the AC circuit breakers that power the power cables installed in the enclosure. The installation is complete. Setting up the HP BladeSystem - HP BladeSystem c3000 | HP BladeSystem c3000 Enclosure Quick Setup Instructions - Page 14
press OK to apply the Enclosure Settings (Power Mode, Power Limit, Dynamic Power, Rack Name, and Insight Display PIN) to other linked enclosures. 11. Follow the instructions on the next screen. 12. Follow the instructions on the next screen. 13. Open a browser and connect to the active Onboard - HP BladeSystem c3000 | HP BladeSystem c3000 Enclosure Quick Setup Instructions - Page 15
and firmware from the SPP download site (http://www.hp.com/go/spp/download). For more information, download the HP Service Pack for ProLiant (SPP) from the HP website (http://www.hp.com/go/spp/download). Troubleshooting resources The HP BladeSystem c-Class Enclosure Troubleshooting Guide provides - HP BladeSystem c3000 | HP BladeSystem c3000 Enclosure Quick Setup Instructions - Page 16
in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein. Part Number: 446990-006 February 2013 Edition: 6 *446990-006
HP BladeSystem c3000 Enclosure
Quick Setup Instructions
Part Number 446990-006