HP BladeSystem c3000 HP BladeSystem c3000 Enclosure Quick Setup Instructions
HP BladeSystem c3000 Manual
View all HP BladeSystem c3000 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP BladeSystem c3000 manual content summary:
- HP BladeSystem c3000 | HP BladeSystem c3000 Enclosure Quick Setup Instructions - Page 1
HP BladeSystem c3000 Enclosure Quick Setup Instructions Part Number 446990-005 - HP BladeSystem c3000 | HP BladeSystem c3000 Enclosure Quick Setup Instructions - Page 2
2 - HP BladeSystem c3000 | HP BladeSystem c3000 Enclosure Quick Setup Instructions - Page 3
14 Interconnect module Components such as pass-thrus or (quantity and type as switches that enable ordered) communication between the blade and the enclosure 15 Onboard Administrator A removable tray that houses the tray Onboard Administrator module and Insight Display 16 HP c3000 DDR2 The - HP BladeSystem c3000 | HP BladeSystem c3000 Enclosure Quick Setup Instructions - Page 4
20* Printed installation The printed installation instructions instructions for blades, options, and interconnects 21* Installation checklist A checklist that guides you through installation of the enclosure and its components * Not shown Installing the enclosure WARNING: Because - HP BladeSystem c3000 | HP BladeSystem c3000 Enclosure Quick Setup Instructions - Page 5
bay numbering 3. (Optional) Install the enclosure into a rack. See the HP BladeSystem c3000 Enclosure Rack Template. For rack-free installations, omit this step. 4. Install the front cage into the enclosure, then tighten the thumbscrews. Power supply bay numbering Enclosure bay identification - HP BladeSystem c3000 | HP BladeSystem c3000 Enclosure Quick Setup Instructions - Page 6
the Onboard Administrator module into the bay and close the handle. 3. Pull the Insight Display out to lock it into place. Tilt it up, and then rotate it 90 degrees for viewing. 2. To access the Insight Display, press and release the panel. 4. Add any options to each server blade o Additional - HP BladeSystem c3000 | HP BladeSystem c3000 Enclosure Quick Setup Instructions - Page 7
populate device bay 1, and then populate device bay 2. For half-height blades, populate the device bays in the following order: 1, 2, 5, 6. If you plan to install six HP Active Cool 100 Fans, you can install the blades in any configuration. 8. Install device bay blanks into any unused device bays. 7 - HP BladeSystem c3000 | HP BladeSystem c3000 Enclosure Quick Setup Instructions - Page 8
blades, install six fans using all bays. NOTE: You cannot install HP Active Cool 100 fans and HP Active Cool 200 fans in the same enclosure. The Onboard Administrator sends an error message, and you must remove the type of fan with the least number of units installed. 3. Slide the power supply - HP BladeSystem c3000 | HP BladeSystem c3000 Enclosure Quick Setup Instructions - Page 9
power supply bays 1, 4, 2, 5, and 3 Populate all bays 4. Slide the enclosure/Onboard Administrator link module into the bay until the device locks into place. Connecting the cables 1. Identify all connectors. For AC redundant (N+N power supplies) configurations, an even number of power supplies - HP BladeSystem c3000 | HP BladeSystem c3000 Enclosure Quick Setup Instructions - Page 10
this port to remotely communicate with the Onboard Administrator, all iLO ports on each blade, and supporting interconnect module management parts. 2. Connect the management network with a standard CAT5 patch cable. NOTE: If more than one enclosure is installed in the rack, use a CAT5 patch cable to - HP BladeSystem c3000 | HP BladeSystem c3000 Enclosure Quick Setup Instructions - Page 11
Port N+4 One or two single-wide interconnect modules Mezzanine slot 4x port 1 3-4x cards 4x port 2 3/Port N+12 One double-wide 3/Port N+4 interconnect module Mapping BL2x220c blades The following table lists the available configurations for full-height devices installed in device bay N (1-4) 11 - HP BladeSystem c3000 | HP BladeSystem c3000 Enclosure Quick Setup Instructions - Page 12
module to a partner blade in the lower adjacent bay and require a PCIe pass-thru mezzanine card installed in mezzanine connector 3. Onboard Administrator disables the device bay crosslinks in instances where they cannot be used, such as when two blades reside in adjacent device bays. Interconnect - HP BladeSystem c3000 | HP BladeSystem c3000 Enclosure Quick Setup Instructions - Page 13
ordered and the number of fabrics in the configuration. 2. Install interconnect blanks in any unused interconnect bays. 3. Connect each installed interconnect module to the external connections with the appropriate cable. Powering up the enclosure 1. Connect the power cables to the power supplies - HP BladeSystem c3000 | HP BladeSystem c3000 Enclosure Quick Setup Instructions - Page 14
the Enclosure Settings (Power Mode, Power Limit, Dynamic Power, Rack Name, and Insight Display PIN) to other linked enclosures. 11. Follow the instructions on the next screen. 12. Follow the instructions on the next screen. 13. Open a browser and connect to the active Onboard Administrator module - HP BladeSystem c3000 | HP BladeSystem c3000 Enclosure Quick Setup Instructions - Page 15
the Onboard Administrator module to access the remote Onboard Administrator web interface and complete the Onboard Administrator first time installation wizard. To set up the enclosure without network connectivity to the Onboard Administrator, see the HP BladeSystem Onboard Administrator User Guide - HP BladeSystem c3000 | HP BladeSystem c3000 Enclosure Quick Setup Instructions - Page 16
products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein. Bluetooth is a trademark owned by its proprietor and used by Hewlett-Packard Company under license. Part Number
HP BladeSystem c3000 Enclosure
Quick Setup Instructions
Part Number 446990-005