HP Cluster Platform Hardware Kits v2010 Myrinet Interconnect Rack Kit Installa
HP Cluster Platform Hardware Kits v2010 Manual
 |
View all HP Cluster Platform Hardware Kits v2010 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP Cluster Platform Hardware Kits v2010 manual content summary:
- HP Cluster Platform Hardware Kits v2010 | Myrinet Interconnect Rack Kit Installa - Page 1
Platform Myrinet Interconnect Rack Kit Installation Guide Part Number: AA-RW5UA-TE June 2004 This document describes how to install the Myrinet interconnect rack kit into an HP Cluster Platform using the HP Model 10642 rack. This kit is designed to support a Myrinet interconnect with a 3U (5-slot - HP Cluster Platform Hardware Kits v2010 | Myrinet Interconnect Rack Kit Installa - Page 2
contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable - HP Cluster Platform Hardware Kits v2010 | Myrinet Interconnect Rack Kit Installa - Page 3
Interconnect Rack Kit Installation Guide 1 Audience This guide is intended for HP service representatives and other persons trained Resources You can download the documentation for components referenced in this installation guide from the following locations: • HP 10642 rack: http://h18004.www1 - HP Cluster Platform Hardware Kits v2010 | Myrinet Interconnect Rack Kit Installa - Page 4
holes in the vertical surface identified by callout 1. The rail's horizontal surface (callout 2) supports the interconnect chassis. Figure 1: Rail 1 2 4.2 Retainer Brackets The retainer brackets are bracket to the interconnect chassis (callout 2). 2 Myrinet Interconnect Rack Kit Installation Guide - HP Cluster Platform Hardware Kits v2010 | Myrinet Interconnect Rack Kit Installa - Page 5
5U Myrinet interconnects. The most common location for these interconnects is at rack position 0, at the very bottom of the rack. (This installation guide shows the interconnect installed at rack position 0, using the 0-middle and 0-top mounting holes.) 7 Installing the Rail Working from the rear of - HP Cluster Platform Hardware Kits v2010 | Myrinet Interconnect Rack Kit Installa - Page 6
4. CAUTION Use only the specified screws. Screws that are too long might penetrate the switch chassis and damage internal components. 4 Myrinet Interconnect Rack Kit Installation Guide - HP Cluster Platform Hardware Kits v2010 | Myrinet Interconnect Rack Kit Installa - Page 7
injury, always use two people and a stable, elevated work platform to lift any components at a high position in the rack. Myrinet Interconnect Rack Kit Installation Guide 5 - HP Cluster Platform Hardware Kits v2010 | Myrinet Interconnect Rack Kit Installa - Page 8
the Rail Working at the front of the rack, secure the interconnect chassis to the rail, as shown in Figure 7. 6 Myrinet Interconnect Rack Kit Installation Guide - HP Cluster Platform Hardware Kits v2010 | Myrinet Interconnect Rack Kit Installa - Page 9
a total of four screws. Tighten the screws to their specified torque. 11 Removing the Interconnect for Servicing Bring the cluster to an appropriate state for switch component removal and put the rack into a safe chassis all the way out of the rack. Myrinet Interconnect Rack Kit Installation Guide 7 - HP Cluster Platform Hardware Kits v2010 | Myrinet Interconnect Rack Kit Installa - Page 10
Phillips pan-head screws to attach the retainer brackets to the chassis. Use of incorrect screws might damage internal components. 8 Myrinet Interconnect Rack Kit Installation Guide
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
 |
 |
HP Cluster Platform
Myrinet Interconnect Rack Kit Installation Guide
Part Number: AA-RW5UA-TE
June 2004
This document describes how to install the Myrinet interconnect rack kit into an HP
Cluster Platform using the HP Model 10642 rack. This kit is designed to support a Myrinet
interconnect with a 3U (5-slot) chassis or a 5U (9-slot) chassis. Larger models of Myrinet
interconnect require a different kit with a ventilating baffle.
Hewlett-Packard Company
Palo Alto, California