HP D5970A HP Netserver LC 3 Installation Roadmap
HP D5970A - NetServer - LCII Manual
 |
View all HP D5970A manuals
Add to My Manuals
Save this manual to your list of manuals |
HP D5970A manual content summary:
- HP D5970A | HP Netserver LC 3 Installation Roadmap - Page 1
Assistant Windows™ NT, you may use the HP automated installation process. Install the NOS using the HP- guided installation process. ! For a NOS that uses a vendor-installation process, view and print HP NOS Installation Instructions. Install the NOS using the vendor-supplied installation - HP D5970A | HP Netserver LC 3 Installation Roadmap - Page 2
! Internet WWW http://www.hp.com:80/netserver/support/news_main.html ! Internet FTP-ftp://ftp.hp.com; logon: anonymous; password: ; cd NSNAVCD; get 6005.txt ! Compuserve -Call 1-208-334-1691; download 6005.txt from NSNAVCD library To obtain drivers and utilities for the non - HP D5970A | HP Netserver LC 3 Installation Roadmap - Page 3
the power again. If the system fails to boot, follow the instructions on the screen. When HP Navigator starts, you can change its language, set the time and , you will need a flat 1/4-inch screwdriver and T15 TORX® driver. WARNING Before removing the cover, disconnect the power cord and unplug - HP D5970A | HP Netserver LC 3 Installation Roadmap - Page 4
but will not function correctly. ! Use only HP DIMMs listed on the Technical Reference Label located inside the HP NetServer top cover, in Information Assistant, or on . Push the button and lift it up and out of the board guide. 4. Install boards: Insert each board in the desired slot and fasten - HP D5970A | HP Netserver LC 3 Installation Roadmap - Page 5
HP Hard Disk Pack 1. Set the SCSI address: Set the jumpers on the drive to an unused SCSI address. Refer to the drive's installation guide and the SCSI Addressing Examples below for instructions key (provided in the key bag on the rear of the HP NetServer) into the lock on the locking bar. Press in - HP D5970A | HP Netserver LC 3 Installation Roadmap - Page 6
automated NOS installation process, you will be guided through the process by a series of HP display screens. To install the NOS manually: On the Create Driver Diskette(s) screen, select "Create Drivers Diskette(s)." On the Show NOS Installation Instructions screen, select "Save to Disk." Then print
-
1 -
2 -
3 -
4 -
5 -
6
 |
 |
Notice
The information contained in this document is subject to change
without notice.
Hewlett-Packard makes no warranty of any kind with
regard to this material, including, but not limited to, the
implied warranties of merchantability and fitness for a
particular purpose. Hewlett-Packard shall not be liable for
errors contained herein or for incidental or consequential
damages in connection with the furnishing, performance, or use
of this material.
Hewlett-Packard assumes no responsibility for the use or
reliability of its software on equipment that is not furnished by
Hewlett-Packard.
This document contains proprietary information that is protected
by copyright. All rights are reserved. No part of this document
may be photocopied, reproduced, or translated to another
language without the prior written consent of Hewlett-Packard
Company.
Hewlett-Packard Company
Network Server Division
P.O. Box 58059, Technical Marketing
Santa Clara, CA 95052-8059 USA
© Copyright 1998, Hewlett-Packard Company
5967-5230
Printed on recycled paper.
LC 3
Installation
Road Map
HP NetServer
Installation Overview (Road Map Steps in Parentheses)
First: Preparations for Installation
!
!
!
!
!
!
!
!
Read the Road Map
Verify Shipment Contents (1)
Obtain HP Navigator CD-ROM Release History (2)
Set Up and Power On the NetServer (3)
View the Readme File (4)
Test existing hardware using Diagnostic Assistant (4)
Install Information Assistant on Another Computer (4)
Visit Order Assistant (4)
Second: Install Hardware if Needed
!
!
!
!
!
!
!
!
Remove NetServer Covers (5)
Install Memory (6)
Install Additional Boards (7)
Install Mass Storage Devices (8)
Replace Covers and Connect Cables (9)
Power Up the System (10)
Check Indicators, Controls and Ports
Verify Installed Hardware Accessories (10)
Third: Configure Hardware (11)
!
!
!
Configure ISA Non-Plug-and-Play Board (if installed)
Select Network Operating System
Configure Integrated Remote Assistant (Express
Configuration or Custom Menu Item)
Fourth: Install Network Operating System (11)
!
!
For certain versions of Novell NetWare and Microsoft
Windows
NT, you may use the HP automated
installation process. Install the NOS using the HP-
guided installation process.
For a NOS that uses a vendor-installation process, view
and print HP NOS Installation Instructions. Install the
NOS using the vendor-supplied installation utility and
printed instructions.
®
™
Fifth: Install and Configure HP NetServer
Management (11)
!
!
Refer to the
Install HP Top Tools
HP NetServer Management
Reference Guide
Sixth: Install in Rack (Optional) (12)
!
Refer to the
or the instruction sheet that
accompanies the rack installation kit
for instructions on how to mount the
server in a rack.
HP NetServer LC 3 User
Guide
Printed in July 1998.