HP D5970A HP Netserver LH 3r Third Party Rack Installation Guide
HP D5970A - NetServer - LCII Manual
![]() |
View all HP D5970A manuals
Add to My Manuals
Save this manual to your list of manuals |
HP D5970A manual content summary:
- HP D5970A | HP Netserver LH 3r Third Party Rack Installation Guide - Page 1
HP NetServer LH 3r Installation Guide for Compaq® 4000/7000 Racks HP Part Number 5967-5208 Printed in July 1998 - HP D5970A | HP Netserver LH 3r Third Party Rack Installation Guide - Page 2
USA © Copyright 1998, Hewlett-Packard Company. Audience Assumptions The user guide is for the person who installs, administers, and troubleshoots network servers. Hewlett-Packard Company assumes you are qualified in the servicing of computer equipment and trained in recognizing hazards in products - HP D5970A | HP Netserver LH 3r Third Party Rack Installation Guide - Page 3
Contents 1 Introduction 1 HP NetServer LH 3r - Compaq Rack Precautions 4 2 Overview ...5 3 Installation 7 Preparation...7 Marking the Installing the NetServer 11 Installing the Recessed Mounting Brackets 14 4 Warranty and Support 17 HP Repair and Telephone Support 18 Index...19 iii - HP D5970A | HP Netserver LH 3r Third Party Rack Installation Guide - Page 4
- HP D5970A | HP Netserver LH 3r Third Party Rack Installation Guide - Page 5
model 4000- or 7000-series rack enclosure. Refer to the HP NetServer LH 3r Road Map and the HP NetServer LH 3/3r User Guide that came with the NetServer for instructions on adding accessories to and configuring the NetServer. The HP NetServer LH 3 (the pedestal version of this NetServer) cannot be - HP D5970A | HP Netserver LH 3r Third Party Rack Installation Guide - Page 6
front of the rack enclosure. Be sure that the stabilizing, anti-tip feature is installed on the rack enclosure in which you are installing the HP NetServer LH 3r. This option consists of two "feet" at the front of the base of the enclosure and, if you are installing this NetServer - HP D5970A | HP Netserver LH 3r Third Party Rack Installation Guide - Page 7
Chapter 1 Introduction Figure 1-2. Single Rack Enclosure With the Anti-Tip Stabilizing Feature Installed 3 - HP D5970A | HP Netserver LH 3r Third Party Rack Installation Guide - Page 8
instructions, damage to the NetServer or accessories may result. Damage due to improper installation is not covered by the HP Compaq model 4000- or 7000-series rack enclosure. This NetServer is not supported in any other non-HP rack enclosure. • If you choose to use a door on this enclosure - HP D5970A | HP Netserver LH 3r Third Party Rack Installation Guide - Page 9
2 Overview The steps required to install the NetServer in the rack are summarized below: NOTE This is only a summary; detailed instructions are provided on the following pages. • Measure and mark the appropriate holes on all four rack columns • Install one bar nut on each of the - HP D5970A | HP Netserver LH 3r Third Party Rack Installation Guide - Page 10
Chapter 2 Overview Terms used in this document are defined in the table below. Term Definition Bar nut Rack nut Slide Slide mounting flange Rack (rack chassis, rack enclosure) Recessed mounting brackets EIA unit Short, threaded bar used behind slide mounting flanges. Used in place of - HP D5970A | HP Netserver LH 3r Third Party Rack Installation Guide - Page 11
3 Installation This section contains detailed instructions for installing an HP NetServer LH 3r in certain models of the rack enclosure. Mark the bottom and top of this location on the rack columns. The HP NetServer LH 3r measures 8 EIA units tall. Marking the Installation Holes You will mark two - HP D5970A | HP Netserver LH 3r Third Party Rack Installation Guide - Page 12
Chapter 3 Installation 22nd 20th 22nd 20th (At Rear Of Column) 19th 14th 22nd 20th 22nd 20th 15th 11th Figure 3-1. Marking Holes for Installation You will mark two holes on each of the front columns to use for the rack nuts where the two recessed mounting brackets attach to the columns. When - HP D5970A | HP Netserver LH 3r Third Party Rack Installation Guide - Page 13
Chapter 3 Installation Installing the Bar Nuts, Screws, and Rack Nuts Once you have marked the appropriate holes, install the bar nuts and screws on the columns: 1. Position one bar nut behind holes 20 and 22 (previously marked). 2. Insert the two screws, with flat washers, through the two holes - HP D5970A | HP Netserver LH 3r Third Party Rack Installation Guide - Page 14
Chapter 3 Installation Mounting the Slides 1. Orient each slide so that the front of the slide attaches to the front column and the rear attaches to the rear column. This ensures that once installed, the slides will extend correctly, toward the front of the rack (see Figure 3-3). NOTE The slides - HP D5970A | HP Netserver LH 3r Third Party Rack Installation Guide - Page 15
Chapter 3 Installation Push In and Up Figure 3-4. Mounting a Slide to a Column Installing the NetServer 1. Extend the slides until you hear a click, indicating they are fully extended in the locked-out position. Note that the slides do not come apart (see Figure 3-3). WARNING To prevent the - HP D5970A | HP Netserver LH 3r Third Party Rack Installation Guide - Page 16
Chapter 3 Installation 3. Using two people, lift the NetServer using the handles on each side. Move the NetServer in between the extended slide members and position it so that the handles are resting on the slide members (see Figure 3-5 and Figure 3-6). Figure 3-5. Lifting the Server Onto the - HP D5970A | HP Netserver LH 3r Third Party Rack Installation Guide - Page 17
Chapter 3 Installation Figure 3-6. Attaching the Slides to the Server Chassis 13 - HP D5970A | HP Netserver LH 3r Third Party Rack Installation Guide - Page 18
Chapter 3 Installation 5. Remove the two screws from each of the four handles and remove them (see Figure 3-7). Keep these handles and screws for later use, in case you need to remove the NetServer and ship it. Figure 3-7. Remove Mounting Handles 6. Reinstall power supply modules and hard disk - HP D5970A | HP Netserver LH 3r Third Party Rack Installation Guide - Page 19
Chapter 3 Installation To install these brackets: 1. On both slide members, simultaneously depress the lockout releases and push the NetServer completely into the rack enclosure (see Figure 3-8). Lockout Release Figure 3-8. Location of Lockout Releases 15 - HP D5970A | HP Netserver LH 3r Third Party Rack Installation Guide - Page 20
Chapter 3 Installation 2. Install the two screws that hold the tall, left-hand bracket to the face of the NetServer chassis (see Figure 3-9). 3. Install the two screws that hold the short, right-hand bracket to the face of the NetServer chassis (see Figure 3-9). Recessed Brackets Figure 3-9. - HP D5970A | HP Netserver LH 3r Third Party Rack Installation Guide - Page 21
4 Warranty and Support Refer to the warranty statement provided with your original HP NetServer system documentation for the warranty limitations, customer responsibilities, and other terms and conditions. CAUTION Improper installation of HP rack-mount components into third-party racks may result - HP D5970A | HP Netserver LH 3r Third Party Rack Installation Guide - Page 22
Chapter 4 Warranty and Support HP Repair and Telephone Support Refer to the Service and Support chapter of your HP NetServer system documentation for instructions on how to obtain HP repair and telephone support. 18 - HP D5970A | HP Netserver LH 3r Third Party Rack Installation Guide - Page 23
Index C Compaq, 1 F fastening server to rack front, 14 fastening server to slides, 12 H handles removing after mounting, 14 L lifting server into rack, 12 lockout releases, 15 R recessed brackets, attaching, 16 S slide location, 7 V version of NetServer, 1 19
![](/manual_guide/products/hewlettpackard-lh3000r-hp-netserver-lh-3r-party-rack-installation-guide-c0aa0b2/1.png)
HP NetServer LH 3r
Installation Guide
for
Compaq
®
4000/7000 Racks
HP Part Number 5967-5208
Printed in July 1998