HP D5970A HP Ultra/Wide SCSI 4 GB and 9 GB Hard Disk Drive
HP D5970A - NetServer - LCII Manual
View all HP D5970A manuals
Add to My Manuals
Save this manual to your list of manuals |
HP D5970A manual content summary:
- HP D5970A | HP Ultra/Wide SCSI 4 GB and 9 GB Hard Disk Drive - Page 1
HP Ultra/Wide SCSI 4 GB and 9 GB Hard Disk Drive Installation Guide HP Part Number 5967-4544 Printed in June 1998 - HP D5970A | HP Ultra/Wide SCSI 4 GB and 9 GB Hard Disk Drive - Page 2
Clara, CA 95052-8059 USA © Copyright 1998, Hewlett-Packard Company. Audience Assumptions This guide is for the person who installs, administers, and troubleshoots LAN servers. Hewlett-Packard Company assumes you are qualified in the servicing of computer equipment and trained in recognizing hazards - HP D5970A | HP Ultra/Wide SCSI 4 GB and 9 GB Hard Disk Drive - Page 3
4 26 Step 3: Connect the Drive 26 Step 4: Configure the Drive 27 A Jumper Settings 29 Jumper Legend 29 B Disk Drive Characteristics 31 NetWare and DOS 31 OS/2 and Windows NT 32 UNIX and Banyan Vines 33 C Returning HP Hard Disk Drives 35 D Warranty and Support 37 Hardware Warranty 37 iii - HP D5970A | HP Ultra/Wide SCSI 4 GB and 9 GB Hard Disk Drive - Page 4
Contents HP Repair and Telephone Support 37 E Regulatory Information 39 Index...41 iv - HP D5970A | HP Ultra/Wide SCSI 4 GB and 9 GB Hard Disk Drive - Page 5
1 Prepare Drive for Installation Introduction This chapter describes the tools, setup information and the steps necessary to install a SCSI hard disk drive into an HP NetServer. The drives documented in this guide are listed in Table 1-1. Table 1-1. Hard Disk Drive Product Numbers HP Product - HP D5970A | HP Ultra/Wide SCSI 4 GB and 9 GB Hard Disk Drive - Page 6
drive, you need the following tools: • Tweezers, needle-nose pliers or a similar tool for setting configuration jumpers. • A TorxTM T-15 screwdriver or a regular blade screwdriver. Setup Information You Need Before you begin, you need the following setup information: • The HP NetServer Installation - HP D5970A | HP Ultra/Wide SCSI 4 GB and 9 GB Hard Disk Drive - Page 7
to discharge static electricity before handling the drive. When you remove the hard disk drive from the anti-static bag, handle it drive from the packaging. Step 2: Determine the Drive Type The type of the drive varies and drives with the same part number may be of different types. • Match the drive - HP D5970A | HP Ultra/Wide SCSI 4 GB and 9 GB Hard Disk Drive - Page 8
Chapter 1 Prepare Drive for Installation D4910A 4.26 GB Model (Type 1) D4911A 9.10 GB Model (Type 3) D4910A 4.26 GB Model (Type 2) D4911A 9.10 GB GB Model (Type 4) D4910A 4.26 GB Model (Type 5) D4911A 9.10 GB Model (Type 5) Figure 1-1. Identification of the 4 Different Types of Drives 4 - HP D5970A | HP Ultra/Wide SCSI 4 GB and 9 GB Hard Disk Drive - Page 9
or 1-6) for your type of drive, and note the location of the jumpers. The "Disk Drive Characteristics" appendix shows a legend of the drive control settings and the jumper control settings for the individual drives. J6 J2 SCSI Connector J1 Power Connector Figure 1-2. Component Identification, Type - HP D5970A | HP Ultra/Wide SCSI 4 GB and 9 GB Hard Disk Drive - Page 10
Chapter 1 Prepare Drive for Installation J4 SCSI Connector Power Connector Figure 1-3. Component Identification, Type 2 Drives J6 J2 SCSI Connector Power Connector Figure 1-4. Component Identification, Type 3 Drives 6 - HP D5970A | HP Ultra/Wide SCSI 4 GB and 9 GB Hard Disk Drive - Page 11
Chapter 1 Prepare Drive for Installation Figure 1-5. Component Identification, Type 4 Drives Figure 1-6. Component Identification, Type 5 Drives 7 - HP D5970A | HP Ultra/Wide SCSI 4 GB and 9 GB Hard Disk Drive - Page 12
NOT be used because the HP NetServer will time out waiting for the hard disk drive to spin up. Set the drive to the lowest available SCSI first drive), you must change the SCSI address for the drive. • If you are connecting an Ultra/Wide SCSI drive to a narrow SCSI cable and narrow SCSI controller, - HP D5970A | HP Ultra/Wide SCSI 4 GB and 9 GB Hard Disk Drive - Page 13
Chapter 1 Prepare Drive for Installation Figure 1-7. SCSI Address Settings, Type 1 Drives 9 - HP D5970A | HP Ultra/Wide SCSI 4 GB and 9 GB Hard Disk Drive - Page 14
Chapter 1 Prepare Drive for Installation Figure 1-8. SCSI Address Settings, Type 2 Drives 10 - HP D5970A | HP Ultra/Wide SCSI 4 GB and 9 GB Hard Disk Drive - Page 15
Chapter 1 Prepare Drive for Installation Figure 1-9. SCSI Address Settings, Type 3 Drives 11 - HP D5970A | HP Ultra/Wide SCSI 4 GB and 9 GB Hard Disk Drive - Page 16
Chapter 1 Prepare Drive for Installation Figure 1-10. SCSI Address Settings, Type 4 Drives 12 - HP D5970A | HP Ultra/Wide SCSI 4 GB and 9 GB Hard Disk Drive - Page 17
Chapter 1 Prepare Drive for Installation Figure 1-11. SCSI Address Settings, Type 5 Drives 13 - HP D5970A | HP Ultra/Wide SCSI 4 GB and 9 GB Hard Disk Drive - Page 18
an Ultra/Wide SCSI drive to a narrow SCSI cable and narrow SCSI controller. If you are not connecting your drive to a narrow drive. The shape of the connector prevents it from being plugged into the drive incorrectly. Step 5: Continue Installation If you are installing the drive in an HP NetServer - HP D5970A | HP Ultra/Wide SCSI 4 GB and 9 GB Hard Disk Drive - Page 19
view Figure 2-1. Tray Consult Information Assistant on the HP NetServer Navigator CD-ROM for your system for additional information regarding the tray or bracket. Attach a tray to a drive or change a factory-supplied tray (if needed) as follows: • Place the drive on a flat surface, free of static - HP D5970A | HP Ultra/Wide SCSI 4 GB and 9 GB Hard Disk Drive - Page 20
four screws. Step 2: Connect the Drive Activity Light The mounting tray (D2198B) has a drive activity light on the front-panel. The drive activity light flashes during data access and the drive power-on self-test. Connect the drive activity light for your drive as shown in Figures 2-2, 2-3, 2-4, 25 - HP D5970A | HP Ultra/Wide SCSI 4 GB and 9 GB Hard Disk Drive - Page 21
Chapter 2 Mount the Drive in the NetServer L Series Figure 2-3. Activity Light Connection, Type 2 Drives Figure 2-4. Activity Light Connection, Type 3 Drives 17 - HP D5970A | HP Ultra/Wide SCSI 4 GB and 9 GB Hard Disk Drive - Page 22
Chapter 2 Mount the Drive in the NetServer L Series R L RR J3 A AAAE EM 0 1 2 3S DE EE SS Pin 1 Pin 2 +5V Red Cable Black Cable Drive Activity LED Figure 2-5. Activity Light Connection, Type 4 Drives R L RR J3 A AAAE EM 0 1 2 3S DE EE SS Pin 1 Pin 2 +5V Red Cable Black Cable - HP D5970A | HP Ultra/Wide SCSI 4 GB and 9 GB Hard Disk Drive - Page 23
to reach the cables or insert the drive. Consult Information Assistant on the HP NetServer Navigator CD-ROM for your system for instructions. • Insert the mounted hard drive in your HP NetServer. • Connect the internal power supply cable to the hard disk drive with one of the unused cables from - HP D5970A | HP Ultra/Wide SCSI 4 GB and 9 GB Hard Disk Drive - Page 24
and power cords. • Power up your HP NetServer. NOTE If a drive recognition error displays during system startup, press Ctrl+Alt+Del to restart the system. Do not power cycle the system because the drive recognition error will likely repeat. Step 4: Configure the Drive The SCSI controller is - HP D5970A | HP Ultra/Wide SCSI 4 GB and 9 GB Hard Disk Drive - Page 25
Chapter 2 Mount the Drive in the NetServer L Series • Wait until all drives reach full speed. • Press the Reset button on the system or press the Ctrl+Alt+Del hot-key combination to restart the HP NetServer without powering it down. Do not power-down (power-cycle) the system to restart it, as this - HP D5970A | HP Ultra/Wide SCSI 4 GB and 9 GB Hard Disk Drive - Page 26
- HP D5970A | HP Ultra/Wide SCSI 4 GB and 9 GB Hard Disk Drive - Page 27
provides instructions for installing a hard disk drive in the HP NetServer E 45. Consider the following when installing a drive in an HP NetServer E Series system. • The HP NetServer E 45 supports up to four 4 GB or four 9 GB drives. • Drive types D4910A and D4911A are supported in the HP NetServer - HP D5970A | HP Ultra/Wide SCSI 4 GB and 9 GB Hard Disk Drive - Page 28
5 or 6 HP SureStore T4i HP SureStore 8i, 5000i, 2000i Standard SCSI Controller Shelf 3 or 4 Shelf 3 or 4 PCI 1 Slot SCSI Address 0 (default) 0, if it is the first hard drive; for subsequent drives, use address 1, 2 or 3 0, if it is the first hard drive; for subsequent drives, use address 1, 2 or - HP D5970A | HP Ultra/Wide SCSI 4 GB and 9 GB Hard Disk Drive - Page 29
. • Disconnect the power cords. • Detach any external cables. • Remove the cover from the HP NetServer. • Remove any hardware necessary to reach the cables or insert the drive. Consult Information Assistant on the HP NetServer Navigator CD-ROM for your system for specific instructions for removing - HP D5970A | HP Ultra/Wide SCSI 4 GB and 9 GB Hard Disk Drive - Page 30
Chapter 3 Mount the Drive in the NetServer E 45 Mount the Drive in Shelf 3 or 4 • Remove the drive mounting tray from the system. (See Figure 3-2.) Figure 3-2. Hard Disk Drive Mounting Tray • Align the four screw holes in the bottom of the NetServer E 45 tray with the four screw holes in the - HP D5970A | HP Ultra/Wide SCSI 4 GB and 9 GB Hard Disk Drive - Page 31
information about the new hard disk setup, including: model number, capacity, and SCSI. • Reassemble the HP NetServer. • Connect all the cables and power cords. • Turn on power to the HP NetServer. Step 4: Configure the Drive Configure the SCSI controller for the drive using the SCSI SelectTM - HP D5970A | HP Ultra/Wide SCSI 4 GB and 9 GB Hard Disk Drive - Page 32
up). If the system did not recognize a hard drive: • Wait until all drives reach full speed. • Press the Reset button on the system or press the Ctrl+Alt+Del hot-key combination to restart the HP NetServer without powering it down. Do not power-down (power-cycle) the system to restart it, as this - HP D5970A | HP Ultra/Wide SCSI 4 GB and 9 GB Hard Disk Drive - Page 33
bus: no power is supplied to the internal terminators. 4. Drive supplies terminator power to itself (internal connection) and to I/O pin 26 of the SCSI bus. 5. Connects terminator power from the SCSI bus I/O pin 26 to the drive's internal terminator, if present. Each hard disk drive is configured - HP D5970A | HP Ultra/Wide SCSI 4 GB and 9 GB Hard Disk Drive - Page 34
DS Delay Spin-Up On* Motor start up is delayed by the sum of the SCSI ID times 6 seconds after power is applied; i.e., Drive 0 spindle starts immediately, drive 1 starts after a 6 second delay, drive 2 starts after a 12 second delay, and so forth. Off Motor start up begins immediately after system - HP D5970A | HP Ultra/Wide SCSI 4 GB and 9 GB Hard Disk Drive - Page 35
Vines) and corresponding version number: • Extended Translation setting for the controller • Partitions, logical drives or divisions for the hot swap hard disk drive For non-UNIX systems, partition and logical hot swap hard disk drive sizes also depend on: • Partition type (Bootable or Non-bootable - HP D5970A | HP Ultra/Wide SCSI 4 GB and 9 GB Hard Disk Drive - Page 36
Characteristics OS/2 and Windows NT NOTE Configure the controller with "Extended Translation for Drives > 1 GB" enabled. Table B-2. Partitioning Information for OS/2 and Windows NT Maximum Bootable Partition Maximum Non-bootable Drive Operating System OS/2 2.x OS/2 Warp Family Windows NT - HP D5970A | HP Ultra/Wide SCSI 4 GB and 9 GB Hard Disk Drive - Page 37
Maximum Number Operating System SCO UNIX 3.2.4.2 and ODT/OS 3.0 Extended Translation for > 1 GB Drive Disabled SCO UNIX 3.2v5.0 and OS 5.0 Disabled UnixWare 1.1 Disabled UnixWare 2.0.X Disabled UnixWare 2.1.X Disabled Banyan VINES 5.54, 6X and 7.X Disabled SCO Open Server 5.0 Disabled - HP D5970A | HP Ultra/Wide SCSI 4 GB and 9 GB Hard Disk Drive - Page 38
- HP D5970A | HP Ultra/Wide SCSI 4 GB and 9 GB Hard Disk Drive - Page 39
C Returning HP Hard Disk Drives When returning a drive for service, repair, or replacement, use the packaging supplied with the exchange drive. Foam Antistatic Bag Hard Disk Drive Figure C-1. Drive Repackaging 35 - HP D5970A | HP Ultra/Wide SCSI 4 GB and 9 GB Hard Disk Drive - Page 40
- HP D5970A | HP Ultra/Wide SCSI 4 GB and 9 GB Hard Disk Drive - Page 41
provided with your original HP NetServer system documentation for the warranty limitations, customer responsibilities, and other terms and conditions. HP Repair and Telephone Support Refer to the Service and Support section of your HP NetServer system documentation for instructions on how to obtain - HP D5970A | HP Ultra/Wide SCSI 4 GB and 9 GB Hard Disk Drive - Page 42
- HP D5970A | HP Ultra/Wide SCSI 4 GB and 9 GB Hard Disk Drive - Page 43
Name: Address: Hewlett-Packard Company 5301 Stevens Creek Blvd. Santa Clara, CA 95052 USA declares, that the product Product Name: 4 GB and 9 GB Ultra SCSI-3 Disk Drives Model Number(s): HP D4910A and HP D4911A Product Options: N/A conforms to the following Product Specifications: Safety: EMC - HP D5970A | HP Ultra/Wide SCSI 4 GB and 9 GB Hard Disk Drive - Page 44
- HP D5970A | HP Ultra/Wide SCSI 4 GB and 9 GB Hard Disk Drive - Page 45
, 21, 28 front mounting tray, 16 H hardware warranty, 37 HP fast SCSI-2 cables, 19, 26 HP Information Assistant CD-ROM, 2 HP NetServer Road Map, 2 I installation general procedure, 1 NetServer E 45, 23 internal power supply cable, 19, 27 J jumper descriptions, 29 jumper locations D4910A - HP D5970A | HP Ultra/Wide SCSI 4 GB and 9 GB Hard Disk Drive - Page 46
SCSI connector, 19, 26 SCSI controller, 21, 27 SCSI drive power cable, 19, 26 SCSI hard drives multiple, 8 SCSI host bus adapter, 8, 19, 26 SCSI Select utility, 21, 27 SCSI terminators, 29 setup information, 2 shock, 3 start unit command, 30 static electricity, 3 support, 37 system board, 19, 26
HP Ultra/Wide SCSI 4 GB and
9 GB Hard Disk Drive
Installation Guide
HP Part Number 5967-4544
Printed in June 1998