HP D5970A Installing SCO UnixWare on an HP Netserver

HP D5970A - NetServer - LCII Manual

Get HP D5970A - NetServer - LCII PDF manuals and user guides View all HP D5970A manuals
Add to My Manuals
Save this manual to your list of manuals

HP D5970A manual content summary:

  • HP D5970A | Installing SCO UnixWare on an HP Netserver - Page 1
    guide. NOTE: The SCO UnixWare 2.1 and UnixWare 7. X operating system is supported on the HP NetServer LC supported on the HP NetServer LPr LC2000, LH3000, LH6000, LT6000r, LXr8000, and LXr8500 product families. The SCO UnixWare 2.1, UnixWare 7.X operating system is not supported on the HP NetServer
  • HP D5970A | Installing SCO UnixWare on an HP Netserver - Page 2
    HP-Supplied Controllers Troubleshooting Section 2. Installing SCO UnixWare 2.1.x Large Memory Access SCSI Extended Translation Setting MPS Table Setting On NetServer LS and LX for UnixWare HP Bundled NICs Not Supported commands exactly as instructed. Almost all UNIX commands are in lower case so if
  • HP D5970A | Installing SCO UnixWare on an HP Netserver - Page 3
    or tape to install SCO UnixWare. For UnixWare 2.1.x: Installation diskette, SCO UnixWare Host Bus Adapter Drivers diskette, and the HP Drivers diskette (produced from the HP NetServer Navigator CD). Swap Space You may wish to increase the swap space from the default provided. UnixWare uses the swap
  • HP D5970A | Installing SCO UnixWare on an HP Netserver - Page 4
    video memory LC2000, LH3000, LH6000, LT6000r : ATI Rage II C ,1MB or 2MB video memory The wrong video driver can produce blank or unreadable screen displays at the higher (greater than 640 x 480 VGA) resolutions. Host Bus Adapter (HBA) Driver Tips The HP NetServers use the Host Bus Adapter drivers
  • HP D5970A | Installing SCO UnixWare on an HP Netserver - Page 5
    LH 6000 Symbios896 slha & mega LT 6000r Symbios896 slha & mega NOTE: HP currently does not support ultra SCSI mode on the AIC7880 controllers when they are connected to the HP Storage System 6. Ultra SCSI mode is supported for disks installed in the HP NetServer cabinet. Troubleshooting SCO
  • HP D5970A | Installing SCO UnixWare on an HP Netserver - Page 6
    have drivers for UnixWare 2.1.x at this time. Consult SCO's hardware compatability guide for a supported NIC. Installing SCO UnixWare 2.1.x The following instructions help you to install SCO UnixWare 2.1.x on your HP NetServer system. NOTE: In general, UnixWare can not share IRQs across different
  • HP D5970A | Installing SCO UnixWare on an HP Netserver - Page 7
    that is created by the HP NetServer Navigator CD. 1. Use the HP Navigator CD-ROM installation utility to configure your system hardware. This utility creates the HP NetServer UnixWare 2.1.x Drivers diskette (the "Drivers Diskette"). 2. UnixWare 2.1.0 and 2.1.1 have problems with system memory sizes
  • HP D5970A | Installing SCO UnixWare on an HP Netserver - Page 8
    to 0x7000000 Click OK, and relink the kernel. Reboot the machine. Section 3. Installing UnixWare 7.1.x The following instructions will help you to install SCO UnixWare 7.1.x on your HP NetServer system. NOTE: In general, UnixWare can not share IRQs across different types of controller cards. NOTE
  • HP D5970A | Installing SCO UnixWare on an HP Netserver - Page 9
    installing to - Select Misc, then deselect i2otrans if present, this can cause conflict wilth the HP NetRAID card. - Return to DCU main menu and Save @ Exit. 5. Follow the instructions in the SCO UnixWare Installation Handbook to complete your system installation. Section 4. On-Line Information and
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
HP Server
SCO UnixWare Installation Guide
NOTICE: The information in this document was last updated for the HP NetServer Navigator CD-ROM version
M.04.05. If you don't have the M.04.05 version CD-ROM and you're obtaining this document from the HP web
site as a reference to install an operating system, be sure to also check the HP web site for the latest available
drivers.
©Copyright Hewlett-Packard Company
January 22, 2002
Introduction
This document presents important information that you need to install SCO UnixWare.
The first section of this document is a list of helpful tips on NOS installation, the second
section is a step-by-step installation guide.
NOTE: The SCO UnixWare 2.1 and UnixWare 7. X operating system is
supported on the HP NetServer LC II, LC 3, LD Pro, LH Plus, LH Pro, LH II, LH
3, LH4, LX Pro, LXe Pro,
LXr Pro product families.
The SCO UnixWare 7.X operating system is supported on the HP NetServer LPr
LC2000, LH3000, LH6000, LT6000r, LXr8000, and LXr8500 product families.
The SCO UnixWare 2.1, UnixWare 7.X operating system is
not
supported on the
HP NetServer E 30, E 40, E 45, E 50, E 60, LC, LC Plus, LE, LF, LH, LM, and
LS product families.
The SCO UnixWare 7.1.1 operating system is
not
supported on the HP Server
tc3100 and tc4100 product families.
Hewlett-Packard has more than one Disk Array Controller (DAC) for the
NetServer product family.
In this document the term "HP Disk Array" refers to
the EISA and PCI Disk Array Controller models C3609A and C3610A,
respectively.
The term "HP NetRAID" refers to the HP NetRAID and NetRAID-
1 PCI DAC models D4943A and D4992A, The term "HP NetRAID 3Si" refers to
model number D5955A. The term "HP NetRAID 1Si refers to model number
D2140A. The term"HP Embedded RAID" refers to the built in RAID controller
on the HP NetServer LH3, LH4, LH3000, LH6000 and LT6000r.
The HP NetRAID disk array controllers will be supported on UnixWare 2.1 and
UnixWare 7.X on a future HP NetServer Navigator release.