HP EliteBook 2170p Displaying a custom logo during bootup of HP commercial not
HP EliteBook 2170p Manual
View all HP EliteBook 2170p manuals
Add to My Manuals
Save this manual to your list of manuals |
HP EliteBook 2170p manual content summary:
- HP EliteBook 2170p | Displaying a custom logo during bootup of HP commercial not - Page 1
white paper Displaying a custom logo during bootup of HP commercial notebook systems HowTo Table of contents Introduction 2 Determining the BIOS generation 2 EREPLOGO.EFI Utility 3 Image requirements 3 Command-line switches 3 Obtaining and preparing the EFI shell 3 Instructions for - HP EliteBook 2170p | Displaying a custom logo during bootup of HP commercial not - Page 2
, HP ProBook 4740s, HP ProBook 6475b, HP EliteBook 8470w, HP EliteBook 8470p, HP ProBook 6470b, HP EliteBook 8570p, HP ProBook 6570b, HP EliteBook 2170p, HP EliteBook 8570w, HP EliteBook 8770w, HP EliteBook 2570p EREPLOGO.EFI .jpg BIOS 2011 HP EliteBook 8560w, HP ProBook 4230s, HP ProBook 4330s - HP EliteBook 2170p | Displaying a custom logo during bootup of HP commercial not - Page 3
, run the EREPLOGO.EFI utility from an EFI shell. The .EFI utility puts your custom logo image into the system BIOS. You cannot use this utility if a BIOS password has been set. Image requirements The image must meet the following requirements: • .jpg file format • Resolution range between 424 x 320 - HP EliteBook 2170p | Displaying a custom logo during bootup of HP commercial not - Page 4
FAT32 file system option Instructions for running EREPLOGO.EFI from the EFI shell 1. Boot the system, and then press the f10 key at POST to enter BIOS Setup. 2. Open the System Configuration menu, and then select Boot Options. Under Boot Mode, select UEFI Native mode. 3. Open the File menu, and then - HP EliteBook 2170p | Displaying a custom logo during bootup of HP commercial not - Page 5
folder 9. The EFI shell launches and displays a command prompt of Shell>. 10. Change to the USB key location by typing the drive associated with the key (for example, FS1:), and then press Enter. 11. Go to the location of the EREPLOGO.EFI utility using the cd command, as shown in Figure 5. 5 - HP EliteBook 2170p | Displaying a custom logo during bootup of HP commercial not - Page 6
the f10 key at POST to enter BIOS Setup. 14. Open the System Configuration menu, and then select Boot Options. 15. Under Boot Mode, check Legacy mode to return to the system's original setting while running step 2. 16. Save the changes and exit Setup. The custom logo will now display during POST - HP EliteBook 2170p | Displaying a custom logo during bootup of HP commercial not - Page 7
specify the .bmp or .jpg image file used as the logo displayed during POST. If you enter no parameters or enter invalid parameters, the utility displays a usage statement similar to the following: HPQ EFI BIOS Logo Replace - Version 1.00 Copyright 2008 - Hewlett-Packard Corporation Usage: EREPLOGO - HP EliteBook 2170p | Displaying a custom logo during bootup of HP commercial not - Page 8
key at POST to enter the BIOS Setup. 6. Select System Configuration, and then select Boot Options. 7. Select Custom Logo, and then select Enabled. 8. For BIOS 2011 and BIOS 2012 generations, clear the checkbox for FastBoot. 9. Save the changes and exit Setup. The custom logo will now display during - HP EliteBook 2170p | Displaying a custom logo during bootup of HP commercial not - Page 9
by EREPLOGO.EXE, but no image saved to the HP_TOOLS partition, the image set by ERERPLOGO will display. Systems running BIOS 09, BIOS 2011, or BIOS 2012 The Custom Logo option in the f10 menu is disabled by default. When disabled, the BIOS does not look for any logo in the HP_Tools partition and the - HP EliteBook 2170p | Displaying a custom logo during bootup of HP commercial not - Page 10
/go/getconnected Current HP driver, support, and security alerts delivered directly to your desktop © Copyright 2012 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the
Technical white paper
Displaying a custom logo during bootup of HP
commercial notebook systems
HowTo
Table of contents
Introduction
2
Determining the BIOS generation
2
EREPLOGO.EFI Utility
3
Image requirements
3
Command-line switches
3
Obtaining and preparing the EFI shell
3
Instructions for running
EREPLOGO.EFI from the EFI shell
4
ERPEPLOGO.EXE Utility
6
Image requirements
7
Command-line switches
7
Command-line examples
7
Adding a custom logo to the HP_Tools
partition
8
Priority order of the BIOS-replaced
image and the custom logo in the
HP_Tools partition
8
Systems running BIOS 08
8
Systems running BIOS 09, BIOS 2011,
or BIOS 2012
9
Call to action
10