HP Indigo 7800 Previously Operated Press POP Integration

HP Indigo 7800 Manual

Get HP Indigo 7800 PDF manuals and user guides View all HP Indigo 7800 manuals
Add to My Manuals
Save this manual to your list of manuals

HP Indigo 7800 manual content summary:

  • HP Indigo 7800 | Previously Operated Press POP Integration - Page 1
    Revision number Date Security level To describe how to prepare a previously operated press (POP) for reinstallation. HP Indigo 7800 Digital Press, HP Indigo 7900 Digital Press. CA393-11000 Rev 00 25 June 2020 HP Confidential The information contained in this document is accurate at the date of
  • HP Indigo 7800 | Previously Operated Press POP Integration - Page 2
    press software ...7 Restoring the press configuration ...7 Restoring the press counters ...7 Upgrading the press software and reinstalling Windows ...8 Restoring the press Revision history and confidentiality notice...24 Revision history...24 Printing instructions...24 Confidentiality notice...24 ii
  • HP Indigo 7800 | Previously Operated Press POP Integration - Page 3
    - 4 units HP INDIGO EI MAGENTA 700 - 4 units HP INDIGO EI CYAN 7000, W - 4 units HP INDIGO EI BLACK 7000, - 4 units HP INDIGO EI C.C YELLOW - 4 units HP INDIGO EI C.C MAGENTA - 4 units HP INDIGO EI C.C CYAN 7 - 4 units HP INDIGO EI C.C BLACK 7 - 4 units 90W GSM (330x483mm) - 500 sheets Condat Gloss
  • HP Indigo 7800 | Previously Operated Press POP Integration - Page 4
    Part Number Q5377-00180 MTU PN 52015-308 Description 70gsm - 500 sheets 300gsm - 300 sheets Order QTY 600 sheets 4000 sheets 2 Chapter 1 Overview
  • HP Indigo 7800 | Previously Operated Press POP Integration - Page 5
    as described in the relevant installation document found in CE Suitcase: ● HP Indigo 7800: CA393-08582 - HP Indigo 7800 Digital Press Installation Guide.pdf ● HP Indigo 7900: CA393-09964 - 7900 Press Installation.pdf 3. Open air pressure and check for leaks. 4. Turn on the chiller and check for
  • HP Indigo 7800 | Previously Operated Press POP Integration - Page 6
    panel ● Engine exit door ● ITM Hood cover ● UC door ● Service front door ● Service rear door ● Ink cabinet doors ● Feeder bridge ● Feeder bridge cover upload the following jobs to the press and then print them. Inspect the prints to see the general quality of the press - these jobs are only for
  • HP Indigo 7800 | Previously Operated Press POP Integration - Page 7
    software and I-Fixes for all presses can be found in CE Suitcase, at:C:\CE Suitcase\Common\General\HP Indigo Software Dashboard.mht 2. The following flowchart describes the PC update in the chapters that follow: NOTE: Contact the local software team to get support for PC transfer process. In some
  • HP Indigo 7800 | Previously Operated Press POP Integration - Page 8
    . NOTE: This procedure is done when there is no need to upgrade the press software. For Z420: CA293-07820 - Installing the HP Z420 computer and Windows 7 on an HP Indigo press.pdf For Z440: CA393-09900 - Installing the HP Z440 computer and Windows 7 on an HP Indigo press.pdff 6 Chapter 2 Procedures
  • HP Indigo 7800 | Previously Operated Press POP Integration - Page 9
    on page 5" on page 6). Restoring the press counters If the press counters were not restored automatically, do the following: 1. Change the user level to Technician mode. 2. From the Start menu, click All Programs > HP Indigo press > Tools > Protected counters editor. Alternatively, double
  • HP Indigo 7800 | Previously Operated Press POP Integration - Page 10
    3. Restore bkp2.zip to verify that the file is not corrupted. NOTE: Do not restore the press configuration from an older version - it might fail. 4. Reinstall the press software using HP Indigo Radar, as above. Restoring the press configuration and counters Follow the below steps for restoring the
  • HP Indigo 7800 | Previously Operated Press POP Integration - Page 11
    BOM replacement. 1. Implement kit CA390-13530 - MANDATORY HP INDIGO 7800 DIGITAL PRESS POP 2. Evaluate according to the following table and Engine Engine Engine Engine Engine Engine QTY Description 4 locking paper stop 4 FH sheet separator 8 photosensor 1 Drawer 1 lock mech 1 Drawer
  • HP Indigo 7800 | Previously Operated Press POP Integration - Page 12
    > Simplex Image Adjustment. b. Clear All and select only the Feeder bridge guide adjustment wizard check box > Yes c. Perform front to front (FTF) same direction as they were in the proof tray (do not rotate or flip the sheets). e. Print 12 copies of job FTF_2 JOBS f. Verify that the blue cube is
  • HP Indigo 7800 | Previously Operated Press POP Integration - Page 13
    . Dark media test a. Insert 10 sheets of black substrate into one of the support. Writing Head Perform the following test to set up and verify the quality of Writing Head. NOTE: Make sure that the press troubleshooting: C:\CE Suitcase\Commercial\Bucket\CA393-00150 - Writing Head Installation Guide.pdf
  • HP Indigo 7800 | Previously Operated Press POP Integration - Page 14
    for VCPR. 3. Use following doc for troubleshooting: C:\CE Suitcase\Commercial\Bucket\CA393-00971 - Troubleshooting CPR Issues.pdf. Scratches Follow these steps to check for you to see the white color of the paper. Sample Black Scratch Do not penetrate the color enough to see the color of
  • HP Indigo 7800 | Previously Operated Press POP Integration - Page 15
    types (continued) Scratch Type Description Thin Scratch Can be seen at very specific angle. Sample Deep Scratch Can be seen at any angle Dent Mark Ruler Jig Ser 4". 2. Use this following document for troubleshooting: C:\CE Suitcase\Commercial\Bucket\CA394-02760 - Banding Guide.pdf Banding 13
  • HP Indigo 7800 | Previously Operated Press POP Integration - Page 16
    test these inks during a long run by adjusting the printing mode (from 4x4 to 5x5 or x6 etc.) during a CATP job 1. Back up the press configuration. 2. Long Run Flow: Preparation > Print Samples > Long Run and PQ monitors > Pass/Fail Criteria 3. Preparation: a. Verify that supplies have less than 5k
  • HP Indigo 7800 | Previously Operated Press POP Integration - Page 17
    4 CATP 4/4 5 CATP 300 4/4 6 Cracks & Dripping 4/0 7 CATP 135 4/4 8 PQ Monitors Set 135 4/1 WH CPR Side Fog Blanket Creep Banding Cracks & Dripping CATP Stacker Stacker Proof Stacker Proof 700 2 300 3 100 4 3000 1,2,3,4 3 Any Print Quality Print Quality Cracks &Dripping Print
  • HP Indigo 7800 | Previously Operated Press POP Integration - Page 18
    according to the CATP specification checklists. Table 2-2 ATP - CATP specification checklists: Item Description paper, as shown below for each paper size: Paper size Distance from Distance from right edge of top edge of page page Max paper & SRA3 10.0 ± 1.0 mm 6.0 ± 1.0 mm On all 10 sheets
  • HP Indigo 7800 | Previously Operated Press POP Integration - Page 19
    Table 2-2 ATP - CATP specification checklists: (continued) Item Description PASS/FAIL/WAIVER D Misregistration U In order to check the Registration between separations, look at the lines above and next to the
  • HP Indigo 7800 | Previously Operated Press POP Integration - Page 20
    Table 2-2 ATP - CATP specification checklists: (continued) Item Description PASS/FAIL/WAIVER J Solid of colored text on white background. Check that all the texts (white and colored, all sizes) are clear and readable, without any ink contamination between letters. The letters should not contain
  • HP Indigo 7800 | Previously Operated Press POP Integration - Page 21
    Table 2-2 ATP - CATP specification checklists: (continued) Item Description O Diamonds, stars, circles, & squares PASS/FAIL/WAIVER The edges of the diamond figures must be sharp and not broken in the
  • HP Indigo 7800 | Previously Operated Press POP Integration - Page 22
    Table 2-2 ATP - CATP specification checklists: (continued) Item Description P Highlight transfer There are Compare to the reference master CATP job. Front to back registration (Duplex side) Hold the sheet up to the light, and check the overlapping of the black borders (S on duplex side against
  • HP Indigo 7800 | Previously Operated Press POP Integration - Page 23
    ATP - CATP specification checklists: ( steps for backing up the computer and software. 1. Stop the press software. 2. Delete all files under Documents: Right-click Start ● My Computer ● Parts Catalog, ● Elo Touchscreen ● HP MyRoom ● HP Indigo PC Back ● Stop_Press ● Start_Press ● Recycle Bin 4. Empty
  • HP Indigo 7800 | Previously Operated Press POP Integration - Page 24
    -60 minutes. d. When the backup completes, click Restart now. 6. Delete the old image backups: a. Right-click Windows Start and select Run. Type y:\ and press Enter. b. Locate the most recent backup files according to their Created date and delete the rest of the files (older backups). Preparing for
  • HP Indigo 7800 | Previously Operated Press POP Integration - Page 25
    that the movement value changed to WH_MOTOR_MOVE_COMPLETE. e. Verify that the writing head reaches its lowest position on both sides. NOTE: Note: If the press is turned on again for any reason, the writing head lowering procedure should be repeated. 9. Verify that there are two bypass keys attached
  • HP Indigo 7800 | Previously Operated Press POP Integration - Page 26
    Initial document Responsible Engineer (TS) Press Group Manager DFE Group Manager R&D instructions Follow these recommendations to achieve the best print quality. Paper weight Page size Printing Simplex/duplex Color Finishing 80 g A4, Letter, or 8.27 x 11.00 in (21 x 27.94 cm) Office printer
  • HP Indigo 7800 | Previously Operated Press POP Integration - Page 27
    be copied, reproduced or distributed in any form or medium, or disclosed to any third party in any manner, without prior written authorization of HP. The copyright notice, which appears in this document, is purely precautionary and shall not be deemed to constitute publication or intent to publish
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
Previously Operated Press (POP) Integration
Document details
Purpose
To describe how to prepare a previously operated press (POP) for reinstallation.
Scope
HP Indigo 7800 Digital Press, HP Indigo 7900 Digital Press.
Document number
CA393-11000
Revision number
Rev 00
Date
25 June 2020
Security level
HP Confidential
The information contained in this document is accurate at the date of release.
Check Knowledge Zone on PrintOS for the most recent version of this document.
The procedures contained in this document can be performed only by HP-Certified CEs or explicitly authorized
operators.
i