HP J3278B Quick Setup - 5967-9985

HP J3278B - SureStore CD-ROM Server/Tower 7 NAS Server Manual

Get HP J3278B - SureStore CD-ROM Server/Tower 7 NAS Server PDF manuals and user guides View all HP J3278B manuals
Add to My Manuals
Save this manual to your list of manuals

HP J3278B manual content summary:

  • HP J3278B | Quick Setup - 5967-9985 - Page 1
    the parts needed for installation: Power Cords (2) HP SureStore HD Server 4000 User's Guide (for more information) You also need: • IP settings using DHCP or BOOTP, press . -or- • To set the IP settings manually at the control panel, follow these steps: 1. Press $ . The third message at left
  • HP J3278B | Quick Setup - 5967-9985 - Page 2
    this first installation. Follow the instructions on the screen. When you troubleshooting help. Visit HP's support website at: www.hp.com/support/hdserver Call HP Customer Care. See appendix A in the User's Guide. HP SureStore Network Attached Storage 5967-9985 Copyright 1999 c Hewlett-Packard
  • 1
  • 2
▼
▲
▼
▲
▼
▲
Configure IP settings
Verify hardware installation
HP
SureStore
Network Attached Storage
1
5
4
2
Locate parts
Quick Setup
Press to use
DHCP/BOOTP or...
Press to set
IP manually
R
IP Address
0
00.000.000.000
1
2
You also need:
•
A twisted-pair network cable with RJ-45 connectors (not included).
•
Two power outlets.
•
An IP address, subnet mask, and, optionally, the default gateway
(router). Configure them using DHCP or BOOTP, or manually at the
server control panel. See your IP administrator for this information.
When the control panel prompts you (first two messages at left), do one of the following:
•
To set the IP settings using DHCP or BOOTP, press
.
-or-
•
To set the IP settings manually at the control panel, follow these steps:
1.
Press
. The third message at left appears, with the first 0 blinking.
2.
Enter the IP address.
Use
▲▼
to change the blinking number, and press
to select a
number and move to the next space. (Use
to move to a previous space.) Once you set
the last number, press
to accept the new IP address.
3.
Enter the subnet mask.
Press
▼
. To change the subnet mask, press
and enter a new
one the same way you entered the IP address. When finished, press
.
4.
Enter the default gateway .
Press
▼
. To change the default gateway, press
and enter
a new one the same way you entered the IP address. When finished, press
.
5. Press
to exit setup mode, and then press
to confirm.
Connect the network cable
On the back of the server, attach
the network cable between the
server and the network connector
at the wall.
Plug in power cords
3
1.
Caution!
Ensure that the
voltage switches are set
correctly for your country.
2. Plug the two power cords into
the back of the server, and
then plug the other ends of
the cords into the power
outlets.
Caution!
If you need different power
cords than the ones supplied,
use power cords approved for
your country. See chapter 3 in
the
User's Guide
.
Locate the parts needed for installation:
HP SureStore
HD Server 4000
Power Cords (2)
User's Guide
(for
more information)
On the front of the server, switch on the power and
check the following:
If any of these checks fail, see chapter 11 in the
User's Guide
.
Main power light above power switch is
on.
Control panel display shows varying
self-test and loading messages.
Power and activity lights for all hard
drives blink indicating self-test, and
then power lights remain
green
.
Power display reads
HP
.