HP LC2000r HP Netserver LXr Pro8 30/FC Config Guide for Windows NT4.0 Cluster
HP LC2000r - NetServer - 128 MB RAM Manual
View all HP LC2000r manuals
Add to My Manuals
Save this manual to your list of manuals |
HP LC2000r manual content summary:
- HP LC2000r | HP Netserver LXr Pro8 30/FC Config Guide for Windows NT4.0 Cluster - Page 1
the supported HP NetServer LX Pro, LXe Pro and A3661B High Availability Disk Array Model 30/FC (LX, LXe/Model 30-FC) configurations for Microsoft Cluster Server. These configurations minimize single points of failure, provide maximum availability, and have been certified by Hewlett-Packard and - HP LC2000r | HP Netserver LXr Pro8 30/FC Config Guide for Windows NT4.0 Cluster - Page 2
BIOS version CPU cache RAM No. of power supplies Hot swap cages Local storage I/O slots: LANs LAN connection NIC: Model Driver No. of NICs SPU I\O slot Local Storage Physical drive location Disk drives Controller SCSI bus HP NetServer LX Pro Model 1 or HP NetServer LXe Pro Model 1 166 or 200 MHz - HP LC2000r | HP Netserver LXr Pro8 30/FC Config Guide for Windows NT4.0 Cluster - Page 3
Host Bus Adapter: Model No. of HBA Driver SPU I/O slot Disk Array Controller: Model No. of controllers Microcode Disk Array Storage: Model No. of cabinets Controller Disk capacities: ArrayGUIde RAID levels Logical units Hot spares Power Supply RAID arrays A5246A HP Fibre Channel Adapter Kit for NT - HP LC2000r | HP Netserver LXr Pro8 30/FC Config Guide for Windows NT4.0 Cluster - Page 4
See Shared Storage.): No. of Disk Arrays No. of Controllers See "Basic Configuration Cabling Diagrams with Single or Cascaded Hubs Cabling Diagrams with Single or Cascaded Hubs." A3724A HP 10-port Short Wave Fibre Channel (FC) Hub A4839A HP 10-port Long Wave FC Hub Basic Configuration: - HP LC2000r | HP Netserver LXr Pro8 30/FC Config Guide for Windows NT4.0 Cluster - Page 5
See Shared Storage Cables for a list of cables that can be connected to the Short Wave Ports of the hub. Port connections to this hub are for example only. You can use any port, except for port 10 on Long Wave Hubs. The remaining ports can be used for connection of additional Disk Arrays. Basic - HP LC2000r | HP Netserver LXr Pro8 30/FC Config Guide for Windows NT4.0 Cluster - Page 6
See Shared Storage Cables for a list of cables that can be connected to the Short Wave Ports of the hub. Port connections to these hubs are for example only. You can use any port, except for port 10 on Long Wave Hubs. The remaining ports can be used for connection of additional Disk Arrays. See - HP LC2000r | HP Netserver LXr Pro8 30/FC Config Guide for Windows NT4.0 Cluster - Page 7
See Shared Storage Cables for a list of cables that can be connected to the Short Wave Ports of the hub. Port connections to these hubs are for example only. You can use any port, except for port 10 on Long Wave Hubs. The remaining ports can be used for connection of additional Disk Arrays. - HP LC2000r | HP Netserver LXr Pro8 30/FC Config Guide for Windows NT4.0 Cluster - Page 8
See Shared Storage Cables for a list of cables that can be connected to the Short Wave Ports of the hub. Port connections to these hubs are for example only. You can use any port, except for port 10 on Long Wave Hubs. The remaining ports can be used for connection of additional Disk Arrays. See
1
HP NetServer LX Pro and LXe Pro
with
A3661B High Availability Disk Array Model 30/FC
Cluster Configuration Guide
25 November, 1998
Introduction
This document defines the supported HP NetServer LX Pro, LXe Pro and A3661B High Availability Disk
Array Model 30/FC (LX, LXe/Model 30-FC) configurations for Microsoft Cluster Server.
These
configurations minimize single points of failure, provide maximum availability, and have been certified by
Hewlett-Packard and Microsoft.
This guide is prescriptive; it describes the configurations supported by HP.
Any configuration not expressly allowed by this guide will not be supported by HP.
What’s Defined
•
Cluster
•
SPUs
•
LANs
•
Local Storage
•
Shared Storage
•
Shared Storage Cabling
Cluster
Type of SPUs
HP NetServer LX Pro Model 1 or HP NetServer LXe Pro Model 1
Each node must be the same model SPU, but may have different clock
speeds, main memory and cache sizes.
Number of nodes
2
Shared Storage
See
Shared Storage
below.
LANs:
Client LAN
See
Client LAN
below.
Intra-cluster
See
Intra-cluster LAN
below.
Power source
Direct from power mains, power conditioner or uninterruptable power
supply (UPS) using any power conditioner or UPS.
System software:
Navigator version
G.00.85 or later
Operating System
Microsoft Windows NT Server 4.0, Enterprise Edition or later.
Service pack
SP3 and hotfix “clusfixi”, or later