HP LH4r HP Netserver LC 3 NetRAID-3Si Config Guide for Windows NT4.0 Clusters
HP LH4r - NetServer - 256 MB RAM Manual
View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals |
HP LH4r manual content summary:
- HP LH4r | HP Netserver LC 3 NetRAID-3Si Config Guide for Windows NT4.0 Clusters - Page 1
Shared Storage LANs: Client Intra-cluster Power source System software: Navigator version Operating System Service pack HP NetServer LC3 Each node must be the same model SPU, but may have different size main memory and cache. 2 HP Rack Storage/12 with HP NetRAID-3Si controller and HP disks. See - HP LH4r | HP Netserver LC 3 NetRAID-3Si Config Guide for Windows NT4.0 Clusters - Page 2
Disk drives Controller SCSI bus Shared Storage Controller Model No. of controllers Firmware BIOS Driver NetRAID Assistant SPU I/O slot SCSI ID Channels RAID level Logical disks Configuration options: HP NetServer LC3 400, 450, 500, 550 MHz. 1 - 2, but must be the same number of CPUs in each server - HP LH4r | HP Netserver LC 3 NetRAID-3Si Config Guide for Windows NT4.0 Clusters - Page 3
drives: Cables LANs LAN connection NIC: Model Driver No NetRAID Adapters. 1 - 3 Rack Storage/12 D5989B plus 1 D6205B for each Rack Storage/12 5 (fixed) 0 - 3, 8 - 15 (fixed) HP 9.1 GB Ultra SCSI Disk Module D6106A HP 9.1 GB Ultra SCSI Disk Module D6107A HP 18.2 GB Ultra SCSI Disk Module D6108A HP - HP LH4r | HP Netserver LC 3 NetRAID-3Si Config Guide for Windows NT4.0 Clusters - Page 4
Shared Storage Cabling This part of the guide defines the allowable cabling configurations for clusters using the HP NetServer LC3 and HP Rack Storage/12s. Only these cabling configurations and cables are supported. HP Microsoft Cluster using HP Rack Storage/12 4 - HP LH4r | HP Netserver LC 3 NetRAID-3Si Config Guide for Windows NT4.0 Clusters - Page 5
Version History 20 March 2000 20 January 2000 Corrected references to software versions "or later". Initial release. 5 - HP LH4r | HP Netserver LC 3 NetRAID-3Si Config Guide for Windows NT4.0 Clusters - Page 6
This page left blank intentionally 6
HP NetServer LC3 with HP Rack Storage/12
Cluster Configuration Guide
30
March
2000
(see Version History at the end of this document)
Introduction
This document defines the supported HP NetServer LC3 configurations with HP Rack Storage/12s and
Microsoft Cluster Server.
These configurations minimize single points of failure (SPOF), provide
maximum availability, and have been certified by Hewlett-Packard and Microsoft.
This guide is
prescriptive; it describes the configurations supported by HP.
Any deviance to these configurations can
result in an inoperative cluster or an operating cluster with degraded performance, hidden SPOFs, etc.,
and therefore will not be supported by HP.
What’s Defined
Cluster
SPUs
Local and Shared Storage
Intra-cluster and Client LANs
Shared Storage Cabling
Cluster
Type of SPUs
HP NetServer LC3
Each node must be the same model SPU, but may have different size
main memory and cache.
Number of nodes
2
Shared Storage
HP Rack Storage/12 with HP NetRAID-3Si controller and HP disks.
See
Shared Storage
below.
LANs:
Client
Any NIC that is HP and Microsoft approved.
See
Client LAN
below.
Intra-cluster
HP D5013A/B with crossover cable.
See
Intra-cluster LAN
below.
Power source
Direct from power mains, power conditioner or uninterruptible power
supply (UPS) using any power conditioner or UPS.
System software:
Navigator version
L.16.05 or later
Operating System
Microsoft Windows NT Server 4.0, Enterprise Edition
Service pack
SP5 or later