HP LH4r HP Netserver LH 3 NetRAID Config Guide for Windows NT4.0 Clusters
HP LH4r - NetServer - 256 MB RAM Manual
 |
View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals |
HP LH4r manual content summary:
- HP LH4r | HP Netserver LH 3 NetRAID Config Guide for Windows NT4.0 Clusters - Page 1
HP NetServer LH 3 with NetRAID (HP Rack Storage/8) Cluster Configuration Guide 18 November 1998 Introduction This document defines the supported HP NetServer LH 3 configurations for Microsoft Cluster Server. These configurations minimize single points of failure, provide maximum availability, and - HP LH4r | HP Netserver LH 3 NetRAID Config Guide for Windows NT4.0 Clusters - Page 2
System software: Navigator version Operating System Service pack SPU Model Clock speed No. of CPUs BIOS version CPU cache RAM No. of power supplies Local storage I/O slots: Storage L.10.00 or later Microsoft Windows NT Server 4.0, Enterprise Edition SP3 and hotfix "clusfixi", or later HP NetServer - HP LH4r | HP Netserver LH 3 NetRAID Config Guide for Windows NT4.0 Clusters - Page 3
Logical disks Configuration options: Cabinet Model No. of cabinets Disk drives: RAID arrays Cables LANs LAN connection NIC: Model Driver No. of NICs SPU I\O slot 1 per RAID array 6 maximum per NetRAID adapter Cluster mode on (cache write-through) Ultra SCSI disabled BIOS disabled Set any other - HP LH4r | HP Netserver LH 3 NetRAID Config Guide for Windows NT4.0 Clusters - Page 4
Shared Storage Cabling This part of the guide defines the allowable cabling configurations for clusters using the HP NetServer LH 3 and HP Rack Storage/8s. Only these cabling configurations and cables are supported. HP Microsoft Cluster Server with One HP NetRAID Adapter 4 - HP LH4r | HP Netserver LH 3 NetRAID Config Guide for Windows NT4.0 Clusters - Page 5
HP Microsoft Cluster Server Power Cabling 5 - HP LH4r | HP Netserver LH 3 NetRAID Config Guide for Windows NT4.0 Clusters - Page 6
This page intentionally left blank. 6
-
1 -
2 -
3 -
4 -
5 -
6
 |
 |
HP NetServer LH 3
with
NetRAID (HP Rack Storage/8)
Cluster Configuration Guide
18 November 1998
Introduction
This document defines the supported HP NetServer LH 3 configurations for Microsoft Cluster Server.
These configurations minimize single points of failure, provide maximum availability, and have been
certified by Hewlett-Packard and Microsoft.
This guide is prescriptive; it describes the HP NetServer LH 3
configurations supported by HP.
Any configuration not expressly allowed by this guide will not be
supported by HP.
What’s Defined in Cluster
•
Cluster
•
SPUs
•
Local and Shared Storage
•
Intra-cluster and Client LANs
•
Shared Storage Cabling
Cluster
Type of SPUs
HP NetServer LH 3
Each node must be the same model SPU, but may have different size main
memory, cache, and CPU clock speeds.
Installation
Pedestal or racked
Number of nodes
2
Shared Storage
HP Rack Storage/8 with HP NetRAID controller and HP disks.
See
Shared Storage
below.
LANs:
Client LAN
Any NIC that is HP and Microsoft approved.
See
Client LAN
below.
Intra-cluster
(Heartbeat) LAN
HP D5013A or J3171A only with crossover cable. See
Intra-cluster LAN
below.
Power source
Direct from power mains, power conditioner or uninterruptible power
supply (UPS) using any power conditioner or UPS.