HP LH4r HP Netserver LP 2000r (1.13, 1.26 & 1.40 GHz) Technical Reference

HP LH4r - NetServer - 256 MB RAM Manual

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

HP LH4r manual content summary:

  • 1
P4636-80201
Control Panel
hp
netserver lp2000r
Disk 4
Disk 5
Disk 3
Disk 1
Disk 2
Disk 0
Temperature/Fans
SCSI
Activity
Power
S upply
Power Switch
Flexible Disk Drive
Power
Reset
C
Label Manufacturer to print part
number in Code 39 barcode here
Netserver
Use only PC 133 HP DIMMs.
F
Memory
The LP 2000r can support up to 4GB.
D
Rear Panel
AC Power
for PS 2
Power
Supply 2
Power
Supply 1
Power LEDs
Mouse
Keyboard
Parallel
Serial B
USB (2)
PCI Slots (3)
Video
Serial A/Mgmt
LAN A/Mgmt
External SCSI
Connector
LAN B
AC Power for PS 1
Enlarged LAN
Connector
Activity
LED
Speed
LED
G
Standard SCSI Cabling
Duplex SCSI Cabling
HDD 0
HDD 1
HDD 2
HDD 3
HDD 4
HDD 5
IDE-1
FDD
System Board
3
2
1
SCSI A
SCSI B
FDD
CD-ROM
5
DAC Duplex SCSI Cabling
HDD 0
HDD 1
HDD 2
HDD 3
HDD 4
HDD 5
IDE-1
FDD
System Board
3
5
4
2
1
SCSI 0
SCSI 1
SCSI B
External
SCSI
FDD
CD-ROM
DAC
HDD 0
HDD 1
HDD 2
HDD 3
HDD 4
HDD 5
IDE-1
FDD
System Board
3
4
2
1
SCSI A
SCSI B
External
SCSI
FDD
CD-ROM
5
Mass Storage Device Locations
and Settings
See documentation with each device for further configuration information.
E
See Panel
S lot 0 through 5
Embedded
Factory installed
Factory Installed
Drives may be installed in
S lot 0 through 5
SCSI ID 7
Flexible Disk Drive
Device
Device Settings
Location (in order
of recommendation)
Standard IDE CD-ROM Drive
HP Accessory 9 GB HDD or
HP Accessory 18 GB HDD or
HP Accessory 36 GB HDD
Standard Dual SCSI Controller
A
See Panel
A
Steady green when operating normally. Flashing green at 1 Hz rate in sleep mode.
Steady green for normal operation. Steady red indicates overtemperature, or fan failure.
Alternating green and red indicates warning.
Flashing green when there is SCSI activity. Off when there is no activity.
Steady green when drive is present. Off when drive is not present. Steady red for faulty
drive or rebuild failure. Alternating green and red at 1 Hz rate for SCSI rebuild.
Alternating green and red at 3 Hz rate indentifies drive.
Power
Control Panel LED Definitions
SCSI Activity
Disks
Temperature/Fans
Power Supply
Steady green indicates normal operation. Alternating green and red indicates power
supply warning. S teady red indicates power supply failure.
Steady green indicates normal operation. Flashing green indicates Standby Mode.
Steady amber indicates power supply failure.
Steady green indicates link is valid. Flashing green indicates activity on LAN.
Steady amber indicates link rate of 100mbps. Off indicates link rate of 10mbps.
Power
Rear Panel LED Definitions
LAN Activity
LAN Speed
Electronic Support Services
Support Questions
Selected HP Accessories
Internet Web Page
Internet FTP
Compuserve Library
HP Navigator CD
GO HPPC
•
•
•
•
HP-Authorized Reseller
Compuserve Discussion Forum
US / Canada Phone Support
Europe Phone Support
GO HPPC
1-970-635-1000
(+31-20) 581-3330
(Netherlands)
•
•
•
•
This information is subject to change without notice and
is provided without warranty.
© Copyright 2000 Hewlett-Packard Company
This Technical Reference Label is for trained service personnel.
Hewlett-Packard Company assumes you are qualified in the
servicing of computer equipment and trained in recognizing
hazards in products with hazardous energy levels.
Audience Assumptions
Electrostatic Discharge (ESD) Warning
To avoid catastrophic or hidden damage to components,
wear a wrist strap and use a static-dissipative work surface
connected to the chassis when handling components. Use
an antistatic service kit, such as 3M 8501/8502/8505 or
equivalent.
®
For other tested accessories, download the Order Assistant
from the HP Web page.
HP has offices in over 100 countries.
Check your local telephone directory.
Service Information
H
B
System Board
1. IDE CD-ROM
2. Flexible Disk Drive
3. Hard Drive
4. Bootable Cards
5. Network Connection
Boot Order
Clear CMOS
Clear Password
OPEN
Open = Off Closed = On
Not Used (Default = Off)
BIOS Recovery
Not Used (Default = Off)
Not Used (Default = Off)
Not Used (Default = Off)
Not Used (Default = Off)
CAUTION!
Use a new thermal
pad when reinstalling
a heatsink
HP Netserver LP 2000r Technical Reference Label
4MB of standard video memory is
provided with the embedded video
controller.
DIMMs may be installed in any
combination in any DIMM socket.
When handling DIMMs observe
anti-static precautions.
DIMM sizes supported are 128MB,
256MB, 512MB, and 1GB.
Power Supply Removal
Power Supply Insertion
1
2
3
1. Press in to release latch
2. Pull down latch
3. Slide Power Supply out
1. Press in firmly
2. Push up latch to secure
1
2
B
A
A
Do not operate with power
supply slot empty. Close the
slot with a filler panel or a
second power supply.
CAUTION!
Cables
Type
Flexible Disk
Cable
IDE CD-ROM
Cable
SCSI Cable
Int / Ext SCSI
Cable
1
2
3
5
SCSI Cable,
Long
4
IDE-2
Video
USB (2)
B attery
LAN B
LAN A/Mgmt
S erial A/ Mgmt.
Serial B
DIMMs
0
1
2
3
Power
Connector
Processor 1
Processor 2
Mouse (upper)
Keyboard (lower)
Configuration
Switch
FDD
SCSI B
SCSI A
PCI
Riser
Card
IDE-1
PCI Cage
Connector
Air Flow
Guide
Connector
Integrated
R emote
Assistant
Board
Front Panel
SCSI Cage
S lot 3
S lot 4
S lot 5
SCSI Cage
CD-ROM
Flexible
Disk Drive
PCI Cage
Air Flow Guide
Power Supplies
System Board
CHA_FAN1
S lot 0
S lot 1
S lot 2
CHA_FAN2
B
See Panel
for Control Panel
Parallel
100.0mm REF
100.0mm REF
Blower Assembly
CPU_FAN2
Blower Assembly
Connector