HP LH4r HP Netserver LXr 8500 FC Windows 2000 Config Guide for Windows 2000 A
HP LH4r - NetServer - 256 MB RAM Manual
View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals |
HP LH4r manual content summary:
- HP LH4r | HP Netserver LXr 8500 FC Windows 2000 Config Guide for Windows 2000 A - Page 1
that Hewlett-Packard supports for the HP NetServer LXr 8500, HP Rack Storage/12FC and Microsoft Cluster Server. These configurations minimize single points of failure (SPOF, SPOFless1) and provide extended availability. The specific configuration certified and supported by both Hewlett - HP LH4r | HP Netserver LXr 8500 FC Windows 2000 Config Guide for Windows 2000 A - Page 2
-cluster LAN below. Direct from power mains, power conditioner or uninterruptible power supply (UPS) using any power conditioner or UPS. Redundant power distribution units (PDU's) are strongly recommended. L.18.02 or later Microsoft Windows 2000 Advanced Server HP NetServer LXr 8500 400/450, 500/550 - HP LH4r | HP Netserver LXr 8500 FC Windows 2000 Config Guide for Windows 2000 A - Page 3
tolerant RAID type, e.g. RAID 5, is recommended for all shared storage. HP NetServer Rack Storage/12FC- D5991A Not more than 8 physical drives per logical array and not more than 8 LUNs are permitted per cluster. 1 HP Fibre Channel Array Controller - D5990A 2 (Requires second card be installed in - HP LH4r | HP Netserver LXr 8500 FC Windows 2000 Config Guide for Windows 2000 A - Page 4
SCSI ID Disk SCSI IDs Disk drives: Cables LANs LAN connection NIC: Model Driver No. of NICs HP NetServer Rack Storage/12 - D5989B or C plus two D6025B or two D6025C SCSI cards for each cabinet 5 (fixed) 0 - 3, 8 - 15 (fixed) Same as HP Rack Storage/12FC Any HP LVD SCSI cables from the following - HP LH4r | HP Netserver LXr 8500 FC Windows 2000 Config Guide for Windows 2000 A - Page 5
LAN in P4 Client LAN in P3 HP TopTools Control card in P2 (optional) 2. The two bottom shared storage devices are HP Rack Storage/12 SCSI cabinets. Optional shared storage devices. LEGEND Solid (blue) lines are fibre channel Optical or Copper cables. See inside this guide for specifications - HP LH4r | HP Netserver LXr 8500 FC Windows 2000 Config Guide for Windows 2000 A - Page 6
Power Cabling to Separate Power Circuits (SPOF) (For SPOFless with 2 hubs, connect second hub to PDU that first hub is not attached to) 6 - HP LH4r | HP Netserver LXr 8500 FC Windows 2000 Config Guide for Windows 2000 A - Page 7
Intra-cluster LAN in P4 Client LAN team in P1 and P3 HP TopTools Control card in P2 (optional) 2. The two bottom shared storage devices are HP Rack Storage/12 SCSI cabinets. LEGEND Solid (blue) lines are fibre channel Optical or Copper cables. See inside this guide for specifications. Dashed (green - HP LH4r | HP Netserver LXr 8500 FC Windows 2000 Config Guide for Windows 2000 A - Page 8
LAN in P4 Client LAN team in P1 and P3 HP TopTools Control card in P2 (optional) 2. The two bottom shared storage devices are HP Rack Storage/12 SCSI cabinets. LEGEND Solid (red) lines are copper fibre channel Dashed (green) lines are offset SCSI cables. See inside this guide for specifications. HP - HP LH4r | HP Netserver LXr 8500 FC Windows 2000 Config Guide for Windows 2000 A - Page 9
Versions 29 January 2001 7 November 2000 17 October 2000 19 May 2000 Added D8602B and D6025C cards. Added SPOFless notes and diagrams. Revised intro, boot spec and I/O slots. Added boot priority and Ultra3 drives. Initial release 9
1
HP NetServer LXr 8500
with
HP Rack Storage/12FC & HP Rack Storage/12
Microsoft Windows 2000 Advanced Server
Cluster Configuration Guide
29 January 2001
(see
Versions
at the end of this document)
Introduction
This document defines the configurations that Hewlett-Packard supports for the HP NetServer LXr 8500, HP Rack
Storage/12FC and Microsoft Cluster Server.
These configurations minimize single points of failure (SPOF,
SPOFless
1
) and provide extended availability.
The specific configuration certified and supported by both
Hewlett-Packard and Microsoft is defined, as are other guidelines to assist you in configuring your clustered
NetServers.
This guide is prescriptive; it describes the configurations supported by HP.
Any deviance to these
configurations can result in an inoperative cluster or an operating cluster with degraded performance, hidden
SPOFs, etc., and therefore will not be supported by HP.
What's Defined in a Racked Cluster
•
Cluster
•
SPUs
•
Local and Shared Storage
•
Intra-cluster and Client LANs
•
Shared Storage Cabling
Cluster
Type of SPUs
HP NetServer LXr 8500
Each node must be the same model SPU, but may have different clock
speeds, main memory sizes, cache sizes, and number of CPUs.
Number of nodes
2
Shared Storage
HP Rack Storage/12FC with 2 FCArray Cards, HP disks, and a HP D8602A
or D8602B HBA in each server.
See
Shared Storage
below.
LANs:
Client LAN
Any NIC that is HP and Microsoft approved.
See
Client LAN
below.
For a SPOFless cluster, two D5013B NICs configured with AFT is
recommended.
1
For more information about configuring a SPOFless cluster, refer to the HP white paper,
High Availability MSCS
Cluster Solution
on the HP NetServers, HA Planning website.