HP LH4r HP Netserver LXr Pro 30/FC Installation Guide

HP LH4r - NetServer - 256 MB RAM Manual

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

HP LH4r manual content summary:

  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 1
    cluster supported HP NetServers and the cluster software, and references the Shared Storage Supplement for installation and setup of the shared storage. • Shared Storage Supplement - This supplement is specific to the shared storage device you are using and must be used with the installation guide
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 2
    1 August 1998 Version History Updated the pdf to include the latest version of the HP NetServer Microsoft Cluster Installation Guide. This later version incorporates technical, grammatical and format changes along with adding installation instructions for additional HP NetServers. Package released
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 3
    Guide July 31, 1998 Introduction This document defines the supported HP NetServer LXr Pro with HP A3661B High Availability Disk Array Model 30/FC (LXr Pro/ Model 30-FC) configurations for Microsoft Cluster Server Shared Storage LANs: Client Intra-cluster Power source HP NetServer LXr Pro Model
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 4
    storage I/O slots: LANs LAN connection NIC: Model Driver No. of NICs SPU I\O slot Local Storage Physical drive location Disk drives Controller SCSI bus G.01.00 or later Microsoft Windows NT Server 4.0, Enterprise Edition or later SP 3 and hotfix "clusfixi", or later HP NetServer LXr Pro Model
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 5
    2 meter FC cable, A3531A 16 meter FC cable, A3735A 50 meter FC cable, A3736A 100 meter FC cable, Any cable ≤500 meters per segment that conforms to ANSI X3.230-1994 Fibre Channel Standards Specification (FC-PH) rev 4.3. Any cable ≤2 kilometers that meets ANSI X3.230-1994 Fibre Channel Standards
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 6
    Disk Arrays (See Shared Storage: No. of Disk Arrays No. of Controllers 1-8 1 per Disk Array for Basic Configuration. 2 per Disk Array for Redundant Configuration. 4
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 7
    See Shared Storage Cables for a list of cables that can be connected to the Short Wave Ports of the hub. Port connections to this hub are for example only. You can use any port, except for port 10 on Long Wave Hubs. The remaining ports can be used for connection of additional Disk Arrays. Basic
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 8
    See Shared Storage Cables for a list of cables that can be connected to the Short Wave Ports of the hub. Port connections to these hubs are for example only. You can use any port, except for port 10 on Long Wave Hubs. The remaining ports can be used for connection of additional Disk Arrays. See
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 9
    See Shared Storage Cables for a list of cables that can be connected to the Short Wave Ports of the hub. Port connections to these hubs are for example only. You can use any port, except for port 10 on Long Wave Hubs. The remaining ports can be used for connection of additional Disk Arrays.
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 10
    See Shared Storage Cables for a list of cables that can be connected to the Short Wave Ports of the hub. Port connections to these hubs are for example only. You can use any port, except for port 10 on Long Wave Hubs. The remaining ports can be used for connection of additional Disk Arrays. See
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 11
    HP NetServer Microsoft Cluster Installation Guide with Shared Storage System Supplement NetRAID (Storage System/6, Rack Storage/8 and Rack Storage/12) HP AutoRAID Disk Array Model 12H or HP A3661B Model 30/FC High Availability Disk Array 8 March 1999
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 12
    for errors contained of its software on equipment that reviewed for familiarization with safety markings and instructions used in this manual: • Microsoft and Server Division 10955 Tantau Avenue Cupertino, CA 95014-0770, USA © Copyright 1999, Hewlett-Packard Company HP NetServer Installation Guide
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 13
    (WITH NETRAID LOCAL AND SHARED STORAGE 22 LX/LXR PRO ...24 LXR 8000 ...25 INSTALL SERVICE PACK FOR ALL HP NETSERVERS 27 6 SHARED STORAGE SOFTWARE SETUP 28 SHARED STORAGE SETUP ...28 CREATE THE ARRAY FILE SYSTEMS...28 MATCH DRIVE LETTER ASSIGNMENTS ...33 7 MICROSOFT CLUSTER SERVER SOFTWARE SETUP
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 14
    HP NetServers, set up, assemble and cable the cluster, and install server and cluster software. NOTE This installation guide is incomplete without the supplement specific to your shared storage system. When directed by this guide, turn to the supplement to get the necessary instructions. Version
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 15
    A Graphical Overview to Setting Up the Cluster CAUTION Departing from the sequence shown here may cause unnecessary work and unpredictable results. HP NetServer Installation Guide 5
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 16
    Windows NT, version 4.0 and Service Pack (SP). See the Configuration Guide for your cluster solution for the applicable Windows NT and SP versions and Microsoft Cluster Server installation software. NOTE Some HP NetServers, as stated in part "5 NetServer Software Setup," require installing Windows
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 17
    the Configuration Guide for your cluster. • Cluster Installation Test. Downloaded from the Certified Installer Corner of the HP NetServer Clustering Solutions web site at: at: http://www.hp.com/netserver/products/cluster. • NIC drivers. Download HP drivers from the HP NetServer Clustering Solutions
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 18
    to the Shared Storage Systems and must be installed in specific PCI slots. See the Configuration Guide for your cluster configuration for the HP NetServer PCI slots to use. See instructions supplied with the component or see part "2 NetServer Hardware Setup" of the Shared Storage Supplement for
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 19
    3 Shared Storage Hardware Setup part "3 Shared Storage Hardware Setup" in the Shared Storage Supplement HP NetServer Installation Guide 9
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 20
    the system and instructions in the shared storage supplement. In addition you should have rack layouts of your system printed from the HP NetServers Rack Assistant program. If not, see HP NetServers web site to download this program at: http://www.hp.com/netserver. Connect the LAN Adapters Two sets
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 21
    specific to your HP NetServer as listed below. Secondly, you will install the applicable Service Pack on the NetServer. Select your procedure from the following list: You will... First Second Go to procedure for... LCII LC3 LH Pro LH 3 LH 3 (with NetRAID local storage) LH 4 LPr LPr (with NetRAID
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 22
    addresses and Intra-cluster LAN IP addresses must be on different subnets. LC3 Configure NetServer Hardware and BIOS 1. Make sure you power down System A and power up System B. 2. Insert the HP NetServer Navigator CD in the CD-ROM drive of System B and restart the server. The server boots from the
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 23
    time. NOTE The Client LAN IP addresses and Intra-cluster LAN IP addresses must be on different subnets. LH Pro 1. Make sure you power down System A and power up System B. 2. Insert the HP NetServer Navigator CD in the CD-ROM drive of System B and restart the server. The server boots from the CD
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 24
    sure you power down System A and power up System B. 2. Insert the HP NetServer Navigator CD in the CD-ROM drive and restart the server. 3. During reboot enter the Setup Utility by pressing F2. 4. Select User Preferences and then the LH4 Integrated NetRAID setting you want to use. If you are using
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 25
    1. Remove the HP NetServer Navigator CD, insert the boot floppy for Windows NT4.0, and exit Navigator to reboot the server. 2. When Setup prompts to detect mass storage devices, skip detection and manually specify the mass storage drivers: • The drivers are loaded from the NT 4.0 Drivers floppy disk
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 26
    complete, the D5013A NIC drivers must be manually set to the correct LAN speed. Log on and HP NetServer Navigator CD in the CD-ROM drive and restart the server. 3. During reboot enter the Setup Utility by pressing F2. 4. Using the Setup Utility disable the LH3 Integrated NetRAID. Integrated NetRAID
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 27
    detection and manually specify the mass storage drivers: 3. Load drivers using the NT 4.0 Drivers floppy disk you created in step 13 above (page 17). • Load the driver for the device you want to boot from. This will be the HP NetRAID Adapter Driver. • Load the IDE driver, since the CD drive is on
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 28
    is complete, the D5013A NIC drivers must be manually set to the correct LAN speed. Log on and from the HP NetServer Navigator CD in the CD-ROM drive and restart the server. 3. During reboot enter the Setup Utility by pressing F2. 4. Select User Preferences and then the LH4 Integrated NetRAID
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 29
    in the LH 4 internal bays this will normally be the embedded SCSI Symbios driver. • Secondly, load the IDE driver, since the CD drive is on the IDE bus. • Finally, load any other mass storage drivers you need. If you are using NetRAID for shared storage do not load the HP NetRAID driver at this
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 30
    procedure, LPr (with NetRAID Local and Shared Storage) on page 22. Configure NetServer Hardware and BIOS 1. Make sure you power down System A and power up System B. 2. Insert the HP NetServer Navigator CD in the CD-ROM drive and restart the server. 3. If you have special NetServer local SCSI bus
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 31
    Symbios driver on the drivers disk. Select "SCSI Symbios driver for the HP NetServer LPr." • Secondly, load the IDE driver, since the CD drive is on the IDE bus. • Finally, load any other mass storage drivers you need. If you are using NetRAID for shared storage do not load the HP NetRAID driver at
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 32
    for both. To use NetRAID adapters for both shared and local storage, you must use two adapters. Configure NetServer Hardware and BIOS 1. Make sure you power down System A and power up System B. 2. Insert the HP NetServer Navigator CD in the CD-ROM drive and restart the server. 3. If you have special
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 33
    its IP address and subnet mask. This will be the LAN adapter for the intra-cluster LAN. Select adapter [1] and specify its IP address and subnet mask. This will be the LAN adapter for the client LAN. Set TCP/IP Properties for DNS, WINS Address, etc. at this time. HP NetServer Installation Guide 23
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 34
    intra-cluster LAN should be set to 100 Mbps. Do not use the Auto setting. LX/LXr Pro Configure NetServer Hardware and BIOS 1. Make sure you power down System A and power up System B. 2. Insert the HP NetServer Navigator CD in the CD-ROM drive of System B and restart the server. The server boots from
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 35
    These procedures provide instructions for servers using NetRAID, AutoRAID Model 12H, and Model 30/FC shared storage solutions Configure NetServer Hardware and BIOS 1. Make sure you power down System A and power up System B. 2. Insert the HP NetServer Navigator CD in the CD-ROM drive and restart the
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 36
    , select Properties then Settings and set the network speed to the appropriate setting (either 10 Mbps or 100 Mbps) for your network. The intra-cluster LAN should be set to 100 Mbps. Do not use the Auto setting. HP NetServer Installation Guide 26
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 37
    Service Pack for All HP NetServers Refer to the Configuration Guide for your cluster configuration and install the applicable Microsoft Service Pack (SP3 or SP4). Do not install the Hot Fix associated with Service Pack 3 at this time. NOTE Do not install the Microsoft Cluster Server Software
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 38
    Software Setup" in the Shared Storage Supplement Create the Array File Systems Use the instructions below and Windows NT Disk Administrator to partition, assign drive letters, and format the shared logical drives -shared) disks followed by the shared disk arrays. HP NetServer Installation Guide 28
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 39
    the capacity would be one-half the capacity of the two drives. 3. Click OK to include the full disk in the partition (the default). In the following example, Disk 1 has been partitioned and Disk Administrator assigned a temporary drive letter to the disk array. HP NetServer Installation Guide 29
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 40
    Disk Administrator, Partitioned Disk Array NOTE Do not partition a disk into separate drives. Microsoft Cluster Server Software will only manage one partition per disk. 4. Repeat steps 1 through 3 assigned the next sequential letter to the disk array. HP NetServer Installation Guide 30
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 41
    Drive Letter. Disk Administrator displays the Assign Drive Letter dialog. 3. In the dialog, select a drive letter, and click OK. To avoid confusion later, HP recommends that you choose sequential drive letters. The example in this guide uses drive letters X and Y. HP NetServer Installation Guide
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 42
    the Format dialog make sure that File System is set for NTFS. 4. In the Volume Label field type a label (name) for the drive. Choosing a descriptive label such as "Shared Drive X" will be helpful later when you need to match drive letter assignments at System B. HP NetServer Installation Guide 32
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 43
    you need to shut down System A (but leave it powered on), reboot System B, then assign the same drive letters used on System B as were assigned to System A. Shut Down System A 1. From the Windows NT the computer powered on. The computer is powered on but idle. HP NetServer Installation Guide 33
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 44
    permanent drive letter assignments for each array initialized with System A. 6. When done, Disk Administrator will show matched drive letter assignments as in the opposite node. Exit Disk Administrator. The arrays are now fully configured for use by the cluster. HP NetServer Installation Guide 34
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 45
    CD of Microsoft Windows NT Server, Enterprise Edition in the CD-ROM drive of System B. 2. Run the Microsoft Cluster Server setup program. Setup.exe Cluster Server software setup of System A. Click Next. Microsoft Cluster Administrator, Assigning a Cluster Name HP NetServer Installation Guide 35
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 46
    the LAN adapter according to use (for example, intra-cluster LAN). When you enable cluster use setup gives you three options: • Use for all communications Choose this option if you are configuring a client LAN adapter, and System A and B reside on the same IP subnet. HP NetServer Installation Guide
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 47
    configured all LAN adapters, click Next. 11. Setup lists your LAN adapters and asks you to prioritize them for internal communications between nodes. Move the Intra-cluster LAN to the top of the list so it has the highest priority. See the example dialog below. HP NetServer Installation Guide 37
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 48
    specifications and starts the cluster service. 15. Microsoft Cluster Server is now fully installed on System B. Reboot System B. 16. To finish installation of the Microsoft Cluster Server, leave System B running, go to the next procedure and install MSCS on System A. HP NetServer Installation Guide
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 49
    not already downloaded clusfixi.exe, see "Software" in part "1 What's Needed." 2. Install the Microsoft hotfix clusfixi.exe on System A and System B. NOTE When downloading the file, refer to the Microsoft readme file for instructions on installing the hotfix. HP NetServer Installation Guide 39
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 50
    Hardware Verification and Labeling Utility scans the system and checks system integrity before you perform system configuration. It helps you simplify the contains detailed information on the utility and instructions for setting up and running the utility. HP NetServer Installation Guide 40
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 51
    to download this program. Run CIT Follow the instructions in the CIT program. If additional information is needed refer to CIT on-line help. CIT help is context sensitive and has been expanded to provide detailed instructions for each step of the program. HP NetServer Installation Guide 41
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 52
    HP A3661B Model 30/FC High Availability Disk Array Supplement to HP NetServer Microsoft Cluster Installation Guide July 1, 1998
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 53
    shall not be liable for errors contained herein or for reviewed for familiarization with safety markings and instructions service-trained personnel. Trademark Notice The use of trademarks or other designations is for reference purposes only. The following trademarks are used in this manual
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 54
    AND SETUP ...26 5 - HP NETSERVER SOFTWARE SETUP...34 6 - SHARED STORAGE SOFTWARE SETUP...35 INSTALL THE FIBRE CHANNEL DRIVER ON WINDOWS NT ...35 POWER UP THE HP MODEL 30/FC HIGH AVAILABILITY DISK ARRAY 36 INSTALL THE HP MODEL 30/FC HIGH AVAILABILITY DISK ARRAY SOFTWARE 38 SET THE HP MODEL 30/FC
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 55
    supplement, turn to the installation guide to get the necessary instructions. Operating System The HP Model 30/FC High Availability Disk Array is supported in clustered environments on HP NetServer LXr Pro8 Series systems running the Microsoft Windows NT 4.0 Service Pack 3 or later operating system
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 56
    Service Manual (part number A3232-90002). ì Hewlett-Packard Model 30/FC High Availability Disk Array User's Guide and Service Manual Addendum for Microsoft Windows NT 4.0 (part number A3661-90019). The manuals are enclosed with the hardware components. To part 1 of the HP NetServer Installation
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 57
    an appropriate PCI slot as specified in the Configuration Guide for the HP NetServer. Installation steps are shown for both vertical and horizontal installations. Install a FC I/O adapter in each HP NetServer in the cluster. a. Make sure the HP NetServer is powered down. b. Remove the chassis cover
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 58
    GBIC can only be installed one way, because the GBIC and guide rails inside the FC I/O adapter receptacle are keyed. Installing the GBIC Figure 2. GBIC Module Do not attach Fibre Channel cables to the FC I/O adapter at this time. Also, do not reboot the HP NetServers at this time. To part 2 of the
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 59
    Storage Hardware Setup Install the HP FC-AL Hub 1. Unpack the HP FC-AL Hub a. Unpack and inspect the HP FC-AL hub for any your sales representative if items are missing. FC-AL hub FC-AL Hub Service and User Manual Power cord FC port covers in each port Mounting ear bracket Rubber feet Nylon
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 60
    MAC address (reserved for future use) 8. RS-232 port 9. AC power connector 10. Port LED (Port 1 indicated) Figure 4. HP FC-AL short-wave hub The front panel of the long-wave hub (HP A4839A) appears as follows: 24 11 7 13 5 6 8 9 10 1. Power LED 2. Fault LED 3. Reset button 4. Fibre Channel
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 61
    less than 15 seconds. • If the Fault LED (amber) stays on after self-test, the HP FC-AL hub failed. Contact your sales representative for assistance. • If the Power LED does not light, contact your sales representative. d. Verify the operation of individual ports by inserting the loopback cable into
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 62
    the power source. Refer to the cabinet documentation for more information. Make sure the cabinet is adequately secured and has enough space (1 EIA) for the HP FC-AL hub. Remove filler panels as needed from the front of the cabinet and open the rear door. c. Slide a sheet metal nut onto the
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 63
    column, and insert a 10-32 x .625 machine screw. Securely tighten the screws (see figure 7). Figure 7. Installing the HP FC-AL hub into the cabinet h. The plenum shroud is a back cover that slides onto the HP FC-AL hub. Set the plenum shroud on the front side of the cabinet. Align the holes
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 64
    hub correctly installed in a cabinet If cascading HP FC-AL hubs are being used, install the second HP FC-AL hub, following the same steps used in installing the first HP FC-AL hub. Do not attach Fibre Channel cables or power cords to the HP FC-AL hub at this time. Also, do
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 65
    -Packard Model 30/FC High Availability Disk Array Service Manual (part number A3661-90002) to make sure the installation site meets these requirements. The HP Model 30/FC High Availability Disk Array uses 200VAC to 240VAC nominal; 110VAC is not supported. One power distribution unit (PDU) in the
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 66
    898, or Type K per IEC 947-2. All electrical wiring to the service point (plug) for the disk array should be sized adequately to carry the . 2. Unpack the HP Model 30/FC High Availability Disk Array The HP Model 30/FC High Availability Disk Array must be installed into an HP E3662A or E3662B 2.0m
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 67
    the panel and pull straight out. To install front bezel, press panel onto ballstuds. Ballstud Figure 10. Removing the front bezel 3. Prepare the Cabinet The HP Model 30/FC High Availability Disk Array requires 11 EIA units of space in the cabinet. The hardware mounting kit (part number A3661-60006
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 68
    c. Attach the mounting rails to the cabinet as shown (see figure 11). - Determine the location in the cabinet where the disk array is to be mounted. The disk array should be mounted in the lowest position available in the cabinet. - Install two clip nuts (A in figure 11) over the two holes in the
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 69
    4. Install the HP Model 30/FC High Availability Disk Array in the Cabinet a. Remove CAUTION Do not lift a fan pack by its handle as doing so can damage the fan pack. Replace light (amber) Lock/unlock button ac power cord release latches Back of storage system Holding module at slight angle,
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 70
    b. Remove the battery backup unit (BBU) from the back of the disk array. - Locate the BBU. It is above the power supply units. - Grasp the BBU by inserting your thumbs in the holes and your forefingers into the latches. - Slide the latches inward and hold. - Pull the BBU out of the chassis. Back of
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 71
    c. Remove the power supply units from the back of the disk array - Grasp a power supply unit by its handle. - Squeeze the latch toward the handle. - Pull the power supply unit out of the chassis. - Repeat for the other power supply units. Figure 15. Removing a power supply unit 20
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 72
    d. Mount the disk array chassis into the cabinet. WARNING The disk array is very heavy. Use extreme care when moving or lifting it. At least two persons are needed to lift and safely install a disk array into a cabinet. CAUTION The disk array must be installed so that opening the fan pack door
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 73
    in chapter 1 of the Hewlett-Packard Model 30/FC High Availability Disk Array Service Manual (A3661-90002). Make sure that all the disk slots contain disk modules or the connector. Rail slot Guide slot Disk module's guide Disk module's rail ESD wrist strap Figure 17. Installing a disk module 22
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 74
    f. Replace the power supply units. - Locate the slot where the power supply unit is to be installed. - Slide each power supply unit into its slot while squeezing the latch until it engages the connector. - Press firmly until the power supply unit seats fully into the chassis. Figure 18. Replacing a
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 75
    array. In a basic cluster consisting of two HP NetServers, one HP FC-AL hub and one disk array, the HP FC-AL hub will be connected to SP Each SP requires a unique Fibre Channel address number. Using table 2 as a guide, set the switches for the SP's Fibre Channel address. Each Fibre Channel address
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 76
    77 119 78 120 79 121 7A 122 7B 123 7C 124 7D 125 7E 126 To install additional HP Model 30/FC High Availability Disk Arrays into the same cabinet, first verify that 11 EIA units of space , do not power up the cabinet at this time. To part 3 of the HP NetServer Installation Guide. 25
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 77
    and the cabinet should still be powered down at this time. CAUTION Incorrect wiring can lead to problems, such as devices left off the loop and inaccessible by the HP NetServer. Follow the guidelines below before starting. a. Review the hardware address of each FC-AL device to be connected to the
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 78
    hub. 4. Connect the FC I/O Adapter to the HP FC-AL Hub a. Connect the HP FC-AL hub to the FC I/O adapter on each HP NetServer. Figure 22. An example of an HP FC-AL hub connected to an HP NetServer LXr Pro8 Figure 23. An example of an HP FC-AL hub connected to two HP NetServer LXr Pro8s 27
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 79
    above the SPs. One Fibre Channel connector is associated with each SP. The HP Model 30/FC High Availability Disk Array can have one or two SPs: SP A and SP B (see figure 24). If connecting the disk array to a single HP FC-AL hub, make the connection to SP A. FC address switchesSP A FC connectors SP
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 80
    Figure 26. Example of a cluster with two HP NetServer LXr Pro8s, one HP FC-AL hub and one disk array 29
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 81
    Figure 27. Example of a cluster with two HP NetServer LXr Pro8s and cascaded hubs 30
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 82
    10 of a short-wave hub. Hub A Hub B To Device 1 To Device 2 Figure 28. Cascaded HP FC-AL short-wave hub (HP A3724A) configuration Correct cabling example, HP FC-AL long-wave hub (HP A48394A) In a cascaded configuration of HP FC-AL long-wave hubs, use a long-wave cable to connect the long-wave
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 83
    connections will be eliminated from the FC-AL loop. Figure 30. Incorrect cabling example: connected ports on the same HP FC-AL hub Do NOT leave cables that are connected to the HP FC-AL hub disconnected at the opposite end of the cable. Figure 31. Incorrect cabling example: disconnected cable Do
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 84
    an HP FC-AL hub to more than one other HP FC-AL hub is NOT a supported configuration. Figure 34. Non-supported cabling example: more than two HP FC-AL hubs connected Do not attach power cords or power up the disk array or the cabinet at this time. To part 4 of the HP NetServer Installation Guide. 33
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 85
    5 - HP NetServer Software Setup To part 5 of the HP NetServer Installation Guide. 34
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 86
    Software Setup Install the Fibre Channel Driver on Windows NT The Hewlett-Packard Model 30/FC Disk Array and the cabinet should be powered down at this time. To install the Fibre Channel driver Windows NT, perform the following steps on each HP NetServer in the cluster: a. Power up the HP NetServer
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 87
    the other end of the power cord into one of the power outlets in the PDU. c. If the installation uses cascading HP FC-AL hubs, connect a power cord to the second HP FC-AL hub and plug it into the PDU. 3. Power Up the Cabinet a. Connect the cabinet's power cord to the
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 88
    the disk drive modules do not light up, check that the disk array's power cord is properly installed and connected to the cabinet's PDU. Back of storage system POWER Front of storage system Note: Fan not shown for clarity Figure 36. Powering up the disk array 5. Power Up the HP NetServers When
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 89
    . - Agent runs in the background on an HP NetServer. Install this software utility by following the detailed instructions included in the NT Addendum, Hewlett-Packard Model 30/FC High Availability Disk Array User's Guide and Service Manual Addendum for Microsoft Windows NT 4.0 (part number A3661
  • HP LH4r | HP Netserver LXr Pro 30/FC Installation Guide - Page 90
    Turn off Auto-Trespass a. Make sure that ArrayGUIde has been installed onto the HP NetServers. b. From the Start bar, select Programs. b. Click Windows NT Explorer. c. causes all disk arrays attached to the HP NetServers to reboot automatically. To part 6 of the HP NetServer Installation Guide. 39
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
Microsoft Cluster Installation
Documentation
To assist you in installing your HP NetServer Microsoft Cluster, this file contains three
separate documents combined into one pdf file.
•
Configuration Guide
- This guide provides configuration information specific to your
cluster configuration that you will need during the installation of your cluster.
•
HP NetServer Microsoft Cluster Installation Guide
- This is the first of two
documents used to install the cluster.
It covers the installation of all cluster supported
HP NetServers and the cluster software, and references the Shared Storage Supplement
for installation and setup of the shared storage.
•
Shared Storage Supplement
- This supplement is specific to the shared storage device
you are using and must be used with the installation guide.
It provides instructions for
installing and setting up your shared storage devices.
17 March 1999
(See next page)