HP LH4r HP Netserver LXr Pro Config Guide for Windows NT4.0 Clusters
HP LH4r - NetServer - 256 MB RAM Manual
 |
View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals |
HP LH4r manual content summary:
- HP LH4r | HP Netserver LXr Pro Config Guide for Windows NT4.0 Clusters - Page 1
Guide July 31, 1998 Introduction This document defines the supported HP NetServer LXr Pro with HP A3661B High Availability Disk Array Model 30/FC (LXr Pro/ Model 30-FC) configurations for Microsoft Cluster Server Shared Storage LANs: Client Intra-cluster Power source HP NetServer LXr Pro Model - HP LH4r | HP Netserver LXr Pro Config Guide for Windows NT4.0 Clusters - Page 2
storage I/O slots: LANs LAN connection NIC: Model Driver No. of NICs SPU I\O slot Local Storage Physical drive location Disk drives Controller SCSI bus G.01.00 or later Microsoft Windows NT Server 4.0, Enterprise Edition or later SP 3 and hotfix "clusfixi", or later HP NetServer LXr Pro Model - HP LH4r | HP Netserver LXr Pro Config Guide for Windows NT4.0 Clusters - Page 3
2 meter FC cable, A3531A 16 meter FC cable, A3735A 50 meter FC cable, A3736A 100 meter FC cable, Any cable ≤500 meters per segment that conforms to ANSI X3.230-1994 Fibre Channel Standards Specification (FC-PH) rev 4.3. Any cable ≤2 kilometers that meets ANSI X3.230-1994 Fibre Channel Standards - HP LH4r | HP Netserver LXr Pro Config Guide for Windows NT4.0 Clusters - Page 4
Disk Arrays (See Shared Storage: No. of Disk Arrays No. of Controllers 1-8 1 per Disk Array for Basic Configuration. 2 per Disk Array for Redundant Configuration. 4 - HP LH4r | HP Netserver LXr Pro Config Guide for Windows NT4.0 Clusters - Page 5
See Shared Storage Cables for a list of cables that can be connected to the Short Wave Ports of the hub. Port connections to this hub are for example only. You can use any port, except for port 10 on Long Wave Hubs. The remaining ports can be used for connection of additional Disk Arrays. Basic - HP LH4r | HP Netserver LXr Pro Config Guide for Windows NT4.0 Clusters - Page 6
See Shared Storage Cables for a list of cables that can be connected to the Short Wave Ports of the hub. Port connections to these hubs are for example only. You can use any port, except for port 10 on Long Wave Hubs. The remaining ports can be used for connection of additional Disk Arrays. See - HP LH4r | HP Netserver LXr Pro Config Guide for Windows NT4.0 Clusters - Page 7
See Shared Storage Cables for a list of cables that can be connected to the Short Wave Ports of the hub. Port connections to these hubs are for example only. You can use any port, except for port 10 on Long Wave Hubs. The remaining ports can be used for connection of additional Disk Arrays. - HP LH4r | HP Netserver LXr Pro Config Guide for Windows NT4.0 Clusters - Page 8
See Shared Storage Cables for a list of cables that can be connected to the Short Wave Ports of the hub. Port connections to these hubs are for example only. You can use any port, except for port 10 on Long Wave Hubs. The remaining ports can be used for connection of additional Disk Arrays. See
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
 |
 |
HP NetServer LXr Pro
with
A3661B High Availability Disk Array Model 30/FC
Cluster Configuration Guide
July 31, 1998
Introduction
This document defines the supported HP NetServer LXr Pro with HP A3661B High Availability Disk Array
Model 30/FC (LXr Pro/ Model 30-FC) configurations for Microsoft Cluster Server.
These configurations
minimize single points of failure and provide maximum availability.
They have been certified by Hewlett-
Packard and Microsoft.
This guide is prescriptive; it describes the configurations supported by HP.
If you create any configuration not
expressly allowed by this guide it will not be supported by HP.
HP NetServer clusters have been carefully
designed and tested to allow as much configuration flexibility as possible consistent with high-availability.
What’s Defined
•
Cluster
•
SPUs
•
LANs
•
Local Storage
•
Shared Storage
•
Shared Storage Cables
•
Shared Storage Configurations
Cluster
Type of SPUs
HP NetServer LXr Pro Model 1
Each node must be the same model SPU, but may have different size main
memory, cache, and number of CPUs.
Number of nodes
2
Shared Storage
See
Shared Storage
below.
LANs:
Client
See
Client LAN
below.
Intra-cluster
See
Intra-cluster LAN
below.
Power source
Direct from power mains, power conditioner or uninterruptible power supply
(UPS) using any power conditioner or UPS.