HP LaserJet M4000 QuickPage - Embedded Web Server EWS Configuration to Enable
HP LaserJet M4000 Manual
View all HP LaserJet M4000 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP LaserJet M4000 manual content summary:
- HP LaserJet M4000 | QuickPage - Embedded Web Server EWS Configuration to Enable - Page 1
standard feature in the device firmware on many workgroup HP LaserJets, can be used to provide this capability. This document provides a step-by-step guide to configure HP AutoSend on HP printers and MFPs. IMPORTANT NOTE It is essential that you follow all steps in this document and that the - HP LaserJet M4000 | QuickPage - Embedded Web Server EWS Configuration to Enable - Page 2
2. After setting the SMTP server details: a) Navigate to Settings > AutoSend. b) Select Enable AutoSend and configure to send every 1 day (as shown below). c) Provide the destination email address: [email protected]. Replace the "XX" (as shown here) with the 2-letter code for your - HP LaserJet M4000 | QuickPage - Embedded Web Server EWS Configuration to Enable - Page 3
Section 2 Use the following steps to configure HP AutoSend on these two printers: • HP Color LaserJet CM4540 MFP • HP Color LaserJet CP5520 Series 1. Launch a browser (Internet Explorer 6.0 or greater) and connect to the device home page- http://IPofTheDevice/ (for example, http://16.180.117.170/). - HP LaserJet M4000 | QuickPage - Embedded Web Server EWS Configuration to Enable - Page 4
d) Provide the SMTP server and port (if asked). Use "25" for the port if no other is evident. If required, choose the option to split emails based on email size. NOTE On some models you will not see an input box for "Port". e) Choose the required Server Authentication and click Next. If the SMTP - HP LaserJet M4000 | QuickPage - Embedded Web Server EWS Configuration to Enable - Page 5
f) Click Finish. 2. After setting the SMTP server details: a) Navigate to General > AutoSend. b) Select Enable AutoSend and configure to send every 1 day (as shown below). c) Select Send to Email. d) Provide the destination email address: [email protected]. Replace the "XX" (as shown - HP LaserJet M4000 | QuickPage - Embedded Web Server EWS Configuration to Enable - Page 6
contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable
1
EMBEDDED WEB SERVER CONFIGURATION TO ENABLE
AUTOSEND AND OUTGOING EMAIL FOR HP QUICKPAGE
INTRODUCTION
To ensure accurate billing, the HP QuickPage program requires collection of the metered
information from the printers and multifunction products (MFPs) under contract. HP AutoSend, a
standard feature in the device firmware on many workgroup HP LaserJets, can be used to provide
this capability. This document provides a step-by-step guide to configure HP AutoSend on
HP printers and MFPs.
IMPORTANT NOTE
It is essential that you follow all steps in this document and that the proper
email address for sending the AutoSend report is entered into the
AutoSend “Email Destinations”
CONFIGURATION STEPS
box in the final step.
Prerequisites
1.
Identify the IP address of the printer/MFP: Navigate through the menu in the display panel of
the device and print the configuration page. The IP of the device can be found under the
networking section or under the “Embedded JetDirect” section.
2.
Gather SMTP server details (server name, port, user name, and password if authentication is
required). This can be obtained from the IT admin of the client. This information is vital for
AutoSend to function.
Section 1
Use the following steps to configure HP AutoSend on HP printers and MFPs.
NOTE
Please refer to Section 2 for the following printers:
•
HP Color LaserJet CM4540 MFP
•
HP Color LaserJet CP5520 series
1.
Launch a browser (Internet Explorer 6.0 or greater) and connect to the device home page—
http://IPofTheDevice/ (for example, http://16.180.117.170/).
a)
Navigate to
Settings
>
Email server
and select
Enable outgoing email
to configure the
email server.
b)
Provide the SMTP server IP and port (if asked)
along with the domain name. Use “25” for
the port if no other is evident.
NOTE
On some models you will not see an input box for “Port”.
c)
If the SMTP server requires authentication, provide the username and password.
d)
The Return Email Address is required. The username must be the word “device” and the
customer network domain name should be entered into the Domain Name field.
Example: If the domain name is HP.com, Device email address would be “[email protected]”.
e)
Click
Apply
.