HP Latex 1500 Introductory Information 2

HP Latex 1500 Manual

Get HP Latex 1500 PDF manuals and user guides View all HP Latex 1500 manuals
Add to My Manuals
Save this manual to your list of manuals

HP Latex 1500 manual content summary:

  • HP Latex 1500 | Introductory Information 2 - Page 1
    and safety instructions, describes the printer software, and lists error messages that you may encounter. Where is the user's guide? The following documents are available for your printer, and can be downloaded from http://www.hp.com/go/latex1500/manuals Site preparation guide, site preparation
  • HP Latex 1500 | Introductory Information 2 - Page 2
    PDU) before servicing the printer. The printer must be connected to earth at mains outlets only. To avoid the risk of electric shock: • Do not attempt to dismantle the drying and curing modules, or the e-cabinet except during hardware maintenance tasks. In that case, follow the instructions strictly
  • HP Latex 1500 | Introductory Information 2 - Page 3
    the printer. --Do not attempt to modify LED's array supports, beam and enclosures; Heat Hazard The drying and curing subsystems of the printer operate at section included in the site preparation guide, available at: http://www.hp.com/go/latex1500/manuals. Heavy substrate hazard Special care must
  • HP Latex 1500 | Introductory Information 2 - Page 4
    instructions provided by the printer, and consult the table below. If you feel in doubt about the correct response, or if you have followed the recommendation but the problem persists, call your service of the volume of ink used, or because non-HP ink has been used in the system. See the limited
  • HP Latex 1500 | Introductory Information 2 - Page 5
    Print Server is starting the printer. The printer is shut down or not detected. The firmware update is being performed. The printer is drying the last passes of a job after printing it. Please wait a while. If the printer does not recover, restart it. If the problem persists, check the configuration
  • HP Latex 1500 | Introductory Information 2 - Page 6
    printer (see the user's guide). Substrate may be detached from the See the user's guide. rear spindle or slippage detected. Substrate will be unloaded. System error The printer printing. If the problem persists, run a diagnostic follow the instructions in the message. HP Latex 1500 Printer (Under
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
Introductory Information
1
English
What is it?
The HP Latex 1500 Printer allows you to
print signs and graphics on a wide range of
flexible materials up to 3.20 m (126 in) wide.
The printer uses water-based HP Latex Inks
to provide high quality, durable output.
This introductory document includes legal
notices and safety instructions, describes
the printer software, and lists error
messages that you may encounter.
Where is the user’s guide?
The following documents are available for
your printer, and can be downloaded from
Site preparation guide, site preparation
checklist, installation guide, introductory
information (this document), user’s guide,
legal information, limited warranty.
Legal notices
© Copyright
2016 HP Development Company, L.P.
The information contained herein is subject to change
without notice. The only warranties for HP products and
services are set forth in the express warranty statement
accompanying such products and services. Nothing herein
should be construed as constituting an additional warranty.
HP shall not be liable for technical or editorial errors or
omissions contained herein.
You can find the expressly provided HP Limited Warranty
and Legal Information applicable to your product in the
start menu on your PC and/or in the CD/DVD provided in
the box. For some countries/regions a printed HP Limited
Warranty is provided in the box. In countries/regions where
the warranty is not provided in printed format, you may
request a printed copy from:
http://www.hp.com/go/ orderdocuments
Safety precautions
Before using your printer, read the following safety
precautions and operating instructions to make sure you
use the equipment safely. You are expected to have the
appropriate technical training and experience necessary
to be aware of hazards to which you may be exposed in
performing a task, and to take appropriate measures to
minimize the risks to yourself and to others. Operations
must be supervised at all times.
General safety guidelines
WARNING:
The information provided by the printer status
beacon is only for information purposes and is not related
to any safety provision or safety states. Warning labels on
the printer must be always considered when operating the
printer and prevail against any of the status indicated by
the printer status beacon.
Turn off the printer, using the Branch Circuit Breakers
located in the building’s Power Distribution Unit (PDU),
and call your service representative in any of the following
cases:
•
The power cord is damaged.
•
The drying or curing enclosures are damaged.
•
The printer has been damaged by an impact.
•
Liquid has entered the printer.
•
There is smoke or an unusual smell coming from the
printer.
•
The printer’s built-in Residual Current Circuit Breaker
(Ground Fault Circuit Interrupter) has been repeatedly
tripped.
• Fuses have blown.
•
The printer is not operating normally.
•
There is any mechanical or enclosure damage.
HP Latex 1500 Printer
Introductory Information