HP Mellanox SX1018 SX1018HP Ethernet Managed Blade Switch User Guide for HP c-
HP Mellanox SX1018 Manual
View all HP Mellanox SX1018 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP Mellanox SX1018 manual content summary:
- HP Mellanox SX1018 | SX1018HP Ethernet Managed Blade Switch User Guide for HP c- - Page 1
SX1018HP Ethernet Managed Blade Switch User Guide for HP c-Class BladeSystems PNs: SX1018HP Rev 1.0 www.mellanox.com - HP Mellanox SX1018 | SX1018HP Ethernet Managed Blade Switch User Guide for HP c- - Page 2
A PARTICULAR PURPOSE AND NONINFRINGEMENT ARE DISCLAIMED. IN NO EVENT SHALL MELLANOX BE LIABLE TO CUSTOMER OR ANY THIRD PARTIES FOR ANY DIRECT, INCLUDING, BUT NOT LIMITED TO, PAYMENT FOR PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - HP Mellanox SX1018 | SX1018HP Ethernet Managed Blade Switch User Guide for HP c- - Page 3
Manual 7 Chapter 1 Preparing for Installation 9 1.1 Audience 9 1.2 Kit contents 9 1.3 Mellanox SX1018HP Ethernet Switch Connector Bays 10 1.4 Mellanox SX1018HP the First Time 17 Chapter 4 Removing the Mellanox SX1018HP Ethernet Switch for Service 22 Chapter 5 Regulatory Compliance 23 5.1 - HP Mellanox SX1018 | SX1018HP Ethernet Managed Blade Switch User Guide for HP c- - Page 4
7: Figure 8: Figure 9: Figure 10: Figure 11: Figure 12: Figure 13: Figure 14: SX1018HP Ethernet Switch 9 HP BLade System Onboard Administrator 10 QSFP Connectors 10 Breakout or Fanout Cable 11 Port products 24 For EU non-harmonized telecommunications products 24 4 Mellanox Technologies - HP Mellanox SX1018 | SX1018HP Ethernet Managed Blade Switch User Guide for HP c- - Page 5
SX1018HP Ethernet Managed Blade Switch HW User Manual List of Tables Rev 1.0 Table 1 Table 2 Table 3 Table 4 Table 5 Table 6 Table 7 Table 8 Document Configuration Wizard Session - Static IP Configuration 19 Configuration Wizard Session - Zeroconf Configuration 20 Mellanox Technologies 5 - HP Mellanox SX1018 | SX1018HP Ethernet Managed Blade Switch User Guide for HP c- - Page 6
quality improvement, calls may be recorded or monitored. • It you have purchased a Care Pack (service upgrade), see the Support & Drivers website (http://www8.hp.com/us/en/support-drivers.html). If the problem cannot be resolved at the website, call 1-800-633-3600. For more information about Care - HP Mellanox SX1018 | SX1018HP Ethernet Managed Blade Switch User Guide for HP c- - Page 7
Blade Switch HW User Manual Rev 1.0 About this Manual This manual describes the installation and basic use of the Mellanox SX1018HP switch which is based on the SwitchX-2 switch device. Related Documentation Additional Documentation available from Mellanox: Table 2 - Reference Documents and - HP Mellanox SX1018 | SX1018HP Ethernet Managed Blade Switch User Guide for HP c- - Page 8
to hardware or software. BEWARE! This icon indicates a situation that can potentially cause personal injury or damage to hardware or software. This icon makes a recommendation. 8 Mellanox Technologies - HP Mellanox SX1018 | SX1018HP Ethernet Managed Blade Switch User Guide for HP c- - Page 9
User Guide. Connections differ by server blade type. The information contained in this document explains the cabling between the SX1018HP Ethernet Switch and the network switches. The HP Onboard Administrator screen example (see Figure 2) is a reference for port mapping. Mellanox Technologies - HP Mellanox SX1018 | SX1018HP Ethernet Managed Blade Switch User Guide for HP c- - Page 10
Administrator Preparing for Installation 40GbE is supported in interconnect bays 3 to 8 only. Your screen image might vary by switch type. You can install up to 18 cables in the uplink ports on the SX1018HP Ethernet Switch. 1.3 Mellanox SX1018HP Ethernet Switch Connector Bays Figure 3: QSFP - HP Mellanox SX1018 | SX1018HP Ethernet Managed Blade Switch User Guide for HP c- - Page 11
SX1018HP Ethernet Managed Blade Switch HW User Manual Rev 1.0 port is split into 2 10Gb/s ports, then only SFP+ connectors #1 and #2 are used. Connectors #3 and #4 uplink ports 9 and 10 is a debug port. This is for use by HP FAEs and qualified service technicians only. Mellanox Technologies 11 - HP Mellanox SX1018 | SX1018HP Ethernet Managed Blade Switch User Guide for HP c- - Page 12
Rev 1.0 Preparing for Installation 1.4 Mellanox SX1018HP Ethernet Switch LEDs Figure 6: Switch LEDs 3 4 1 ellanox SX1018HP Ethernet Switch UID P L/A P L/A P L/A P L/A P L/A P L/A 2 1 2 3 4 5 6 Table 3 - LED Assignments Item Description Status 1 Unit ID LED Blue = Activated - HP Mellanox SX1018 | SX1018HP Ethernet Managed Blade Switch User Guide for HP c- - Page 13
Managed Blade Switch HW User Manual 2 Hardware Installation This chapter contains the following sections: • Installing the Mellanox SX1018HP Ethernet Switch • Installing and removing cables in the Mellanox SX1018HP Ethernet Switch 2.1 Installing the Mellanox SX1018HP Ethernet Switch Rev 1.0 All - HP Mellanox SX1018 | SX1018HP Ethernet Managed Blade Switch User Guide for HP c- - Page 14
c-Class interconnect modules together, for example, when another switch is installed in another HP BladeSystem c7000 enclosure that is mounted in the same rack. The Mellanox SX1018HP Ethernet Switches are connected together by the QSFP+ to QSFP+ cables to form a high-performance network. 14 - HP Mellanox SX1018 | SX1018HP Ethernet Managed Blade Switch User Guide for HP c- - Page 15
SX1018HP Ethernet Managed Blade Switch HW User Manual Figure 9: QSFP+ Cable Connector 1 2 3 72 mm max Table 4 - QSFP Mellanox SX1018HP Ethernet Switch To install a cable in the Mellanox SX1018HP Ethernet Switch, follow these steps: 1. Align the cable QSFP+ connector with the Mellanox SX1018HP - HP Mellanox SX1018 | SX1018HP Ethernet Managed Blade Switch User Guide for HP c- - Page 16
installed in port 1 of the Mellanox SX1018HP Ethernet Switch. 2 Mellanox SX1018HP Ethernet Switch. You can install up to 18 cables in the Mellanox SX1018HP Ethernet Switch. It is not installation procedure documented in the cable management bracket installation guide. 16 Mellanox Technologies - HP Mellanox SX1018 | SX1018HP Ethernet Managed Blade Switch User Guide for HP c- - Page 17
SX1018HP Ethernet Managed Blade Switch HW User Manual Rev 1.0 3 Configuring the Switch the First Time The procedures described in this chapter assume that you have already installed and powered-on your switch according to the instructions Display Comments Mellanox configuration wizard You - HP Mellanox SX1018 | SX1018HP Ethernet Managed Blade Switch User Guide for HP c- - Page 18
save changes and exit. To re-run the configuration wizard run the command Choice: "configuration jump-start" in Config mode. Configuration changes saved. 18 Mellanox Technologies - HP Mellanox SX1018 | SX1018HP Ethernet Managed Blade Switch User Guide for HP c- - Page 19
SX1018HP Ethernet Managed Blade Switch HW User Manual . Table 7 - Configuration Wizard Session - Static IP Configuration Wizard Session Display - Static IP Configuration (Example) Mellanox configuration wizard Do you want to use the wizard for initial configuration? yes Step 1: Hostname? [switch] - HP Mellanox SX1018 | SX1018HP Ethernet Managed Blade Switch User Guide for HP c- - Page 20
the Switch the First Time Table 8 - Configuration Wizard Session - Zeroconf Configuration Wizard Session Display - IP Zeroconf Configuration (Example) Mellanox configuration wizard Do you want to use the wizard for initial configuration? yes Step 1: Hostname? [switch] Step 2: Use DHCP - HP Mellanox SX1018 | SX1018HP Ethernet Managed Blade Switch User Guide for HP c- - Page 21
SX1018HP Ethernet Managed Blade Switch HW User Manual Interface source: MTU: HW address: Comment: physical 1500 00:02:C9:11:2A:AE Rev 1.0 313920869 TX packets: 992717 TX discards: 0 TX errors: 0 TX overruns: 0 TX carrier: 0 TX collisions: 0 TX queue len: 1000 Mellanox Technologies 21 - HP Mellanox SX1018 | SX1018HP Ethernet Managed Blade Switch User Guide for HP c- - Page 22
BladeSystem c7000 Enclosure Service and Maintenance Guide: http Mellanox SX1018HP Ethernet Switch might depend on which type of cable management bracket is used to support the cables used in your configuration. If you are unsure of the process to remove a switch for service, contact an HP service - HP Mellanox SX1018 | SX1018HP Ethernet Managed Blade Switch User Guide for HP c- - Page 23
Manual Rev 1.0 5 Regulatory Compliance The chapter lists all of the regulatory notices of compliance for the Mellanox SX1018HP frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Operation of this equipment - HP Mellanox SX1018 | SX1018HP Ethernet Managed Blade Switch User Guide for HP c- - Page 24
on the product. The point of contact for regulatory matters is Hewlett-Packard GmbH, Dept./MS: HQ-TRE, Herrenberger Strasse 140, 71034 Boeblingen, GERMANY. 24 Mellanox Technologies - HP Mellanox SX1018 | SX1018HP Ethernet Managed Blade Switch User Guide for HP c- - Page 25
SX1018HP Ethernet Managed Blade Switch HW User Manual 5.7 Japanese class A notice 5.8 BSMI Notice 5.9 Korean class A notice 5.10 Chinese notice Rev 1.0 Mellanox Technologies 25
www.mellanox.com
SX1018HP Ethernet Managed Blade Switch
User Guide for HP c-Class BladeSystems
PNs: SX1018HP
Rev 1.0