HP Net PC 20 HP Net PC20, Replacing Hardware Components
HP Net PC 20 Manual
 |
View all HP Net PC 20 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP Net PC 20 manual content summary:
- HP Net PC 20 | HP Net PC20, Replacing Hardware Components - Page 1
-bit SDRAM module (D6501A) 64 MB 64-bit SDRAM module (D6502A) 128 MB 64-bit SDRAM module (D6503A) HP NetVectra PC Replacing Hardware Components For information about upgrading your PC and installing accessories, refer to the Accessories Guide, available on HP's web site www.hp.com/go/vectrasupport. - HP Net PC 20 | HP Net PC20, Replacing Hardware Components - Page 2
WARNING HP NetVectra PC Replacing Hardware Components Before You Start Before You Start Static electricity can damage electronic components. Turn all equipment OFF. Don't let your clothes touch the accessory. To equalize the static electricity, rest the accessory bag on top of the Net PC while - HP Net PC 20 | HP Net PC20, Replacing Hardware Components - Page 3
HP NetVectra PC Replacing Hardware Components Removing and Replacing the Cover Removing and Replacing the Cover For your safety, never remove the NetVectra PC telecommunication network. Always replace the cover before switching the NetVectra PC on again. Removing the Cover 1 Switch off the display - HP Net PC 20 | HP Net PC20, Replacing Hardware Components - Page 4
HP NetVectra PC Replacing Hardware Components Removing and Replacing the Cover 5 Pull the sides outward and lift off the cover. — – – Replacing the Cover internal cables are properly connected and safely routed. 2 Pulling out the sides, lower the cover onto the NetVectra PC as shown. — – – 4 English - HP Net PC 20 | HP Net PC20, Replacing Hardware Components - Page 5
HP NetVectra PC Replacing Hardware Components Removing and Replacing the Cover 3 Slide the cover forward into place. 4 Replace the three rear screws. 5 Reconnect all the power cables. English 5 - HP Net PC 20 | HP Net PC20, Replacing Hardware Components - Page 6
HP NetVectra PC Replacing Hardware Components Removing and Replacing the Front Chassis Removing and Replacing the Front Chassis Removing the Front Chassis 1 Remove the cover (described in this - HP Net PC 20 | HP Net PC20, Replacing Hardware Components - Page 7
HP NetVectra PC Replacing Hardware Components Removing and Replacing the Front Chassis 4 On the system board, remove the front panel connector and the floppy disk connector (if you - HP Net PC 20 | HP Net PC20, Replacing Hardware Components - Page 8
CAUTION HP NetVectra PC Replacing Hardware Components Removing and Replacing the Front Chassis Replacing the Front Chassis 1 Replace the connectors to the CD-ROM drive and the hard disk - HP Net PC 20 | HP Net PC20, Replacing Hardware Components - Page 9
HP NetVectra PC Replacing Hardware Components Replacing a Memory Module Replacing a Memory Module Location this chapter). 3 Remove the front chassis and place it upside down on the rear of the NetVectra PC (described in this chapter). It is not necessary to disconnect any cables. 4 Open the two tabs - HP Net PC 20 | HP Net PC20, Replacing Hardware Components - Page 10
HP NetVectra PC Replacing Hardware Components Replacing a Memory Module 5 Line up the two side notches correctly and insert the new memory module. (You can use either slot.) 6 Replace - HP Net PC 20 | HP Net PC20, Replacing Hardware Components - Page 11
HP NetVectra PC Replacing Hardware Components Which Connectors to Use for Mass Storage Devices Which Connectors to Use for Mass Storage Devices When you install a hard disk drive, a - HP Net PC 20 | HP Net PC20, Replacing Hardware Components - Page 12
HP NetVectra PC Replacing Hardware Components Replacing the Hard Disk Drive Replacing the Hard Disk Drive Your NetVectra PC has one hard disk drive installed. You can replace the installed disk drive with a larger disk drive. 1 Remove the computer's cover (described in this chapter). 2 - HP Net PC 20 | HP Net PC20, Replacing Hardware Components - Page 13
HP NetVectra PC Replacing Hardware Components Replacing the Hard Disk Drive 5 Carefully remove the hard disk drive from the front chassis. 6 Carefully slide the hard disk drive into the shelf, and secure the drive with the screws. 7 Place the front chassis upside down on the rear of the NetVectra PC - HP Net PC 20 | HP Net PC20, Replacing Hardware Components - Page 14
HP NetVectra PC Replacing Hardware Components Replacing the Hard Disk Drive 8 Connect the power and data cables to the rear of the drive. The connectors are shaped to - HP Net PC 20 | HP Net PC20, Replacing Hardware Components - Page 15
WARNING HP NetVectra PC Replacing Hardware Components Replacing a Slim CD-ROM Drive Replacing a Slim CD-ROM Drive To avoid electrical shock and harm to your eyes by laser light, do not open the laser module. The laser module should be serviced by service personnel only. Do not attempt to make any - HP Net PC 20 | HP Net PC20, Replacing Hardware Components - Page 16
HP NetVectra PC Replacing Hardware Components Replacing a Slim CD-ROM Drive 6 Remove the old CD-ROM drive from the PC. 7 Remove the CD-ROM rail this chapter). 12 Place the front chassis upside down on the rear of the NetVectra PC. 13 Connect the data cable to the CD-ROM drive and the system board. - HP Net PC 20 | HP Net PC20, Replacing Hardware Components - Page 17
HP NetVectra PC Replacing Hardware Components Replacing a Slim Floppy Disk Drive Replacing a Slim Floppy Disk Drive 1 Switch off the display and computer, and disconnect the power supply cables - HP Net PC 20 | HP Net PC20, Replacing Hardware Components - Page 18
HP NetVectra PC Replacing Hardware Components Replacing a Slim Floppy Disk Drive 7 Slide the floppy drive into the front chassis and secure it with the three screws. 8 Replace the hard disk drive (described in this chapter). 9 Place the front chassis upside down on the rear of the NetVectra PC. 10 - HP Net PC 20 | HP Net PC20, Replacing Hardware Components - Page 19
HP NetVectra PC Replacing Hardware Components Replacing an Accessory Board Replacing an Accessory Board 1 Remove the computer's cover (described in this chapter). 2 Remove the screw and open the - HP Net PC 20 | HP Net PC20, Replacing Hardware Components - Page 20
HP NetVectra PC Replacing Hardware Components Replacing an Accessory Board 4 Align the board's connector with the slot's socket. Firmly press the board into the into place and replace the two screws. 7 Replace the cover (described in this chapter) and reconnect all cables and power cords. 20 English - HP Net PC 20 | HP Net PC20, Replacing Hardware Components - Page 21
HP NetVectra PC Replacing Hardware Components Replacing the System Board Replacing the System Board that secure the board in position and sliding the board out of the PC. 4 Carefully slide the new system board into the PC, aligning the board with the rear connector bracket correctly. Ensure the - HP Net PC 20 | HP Net PC20, Replacing Hardware Components - Page 22
Replacing the System Board 7 Ensure that the latest version of the BIOS is installed on your PC. To learn which BIOS version is currently installed on your PC, press ESC during startup. To get the latest BIOS version for your PC, connect to the web site www.hp.com/go/vectrasupport. 22 English - HP Net PC 20 | HP Net PC20, Replacing Hardware Components - Page 23
HP NetVectra PC Replacing Hardware Components Replacing the Processor Replacing the Processor 1 Remove the that the latest version of the BIOS is installed on your PC. To learn which BIOS version is currently installed on your PC, press ESC during startup. To get the latest BIOS version for your - HP Net PC 20 | HP Net PC20, Replacing Hardware Components - Page 24
HP NetVectra PC Replacing Hardware Components Replacing the Fan Replacing the Fan 1 Remove the computer's cover and the front chassis (described in this chapter). 2 Remove the processor (described - HP Net PC 20 | HP Net PC20, Replacing Hardware Components - Page 25
WARNING HP NetVectra PC Replacing Hardware Components Replacing the Power Supply Replacing the Power Supply To avoid electric shock, do not open the power supply. There are no user-serviceable parts inside. 1 Remove the computer's cover and the front chassis (described in this chapter). 2 Remove - HP Net PC 20 | HP Net PC20, Replacing Hardware Components - Page 26
HP NetVectra PC Replacing Hardware Components Replacing the Internal Battery Replacing the Internal Battery 1 Remove the computer's cover (described in this chapter). 2 Remove the old battery by pressing the clip and then lifting the battery clear of the battery holder with a screwdriver (note the - HP Net PC 20 | HP Net PC20, Replacing Hardware Components - Page 27
HP NetVectra PC Replacing Hardware Components Replacing the Status Panel Replacing the Status Panel 1 Remove the computer's cover and the front chassis (described in this chapter). 2 Release the
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
 |
 |
HP NetVectra PC
Replacing Hardware Components
For information about upgrading your PC and installing accessories,
refer to the
Accessories Guide
, available on HP’s web site
www.hp.com/go/vectrasupport
.
Accessory Board Slots
Main Memory (SDRAM)
32 MB 64-bit SDRAM module (D6501A)
64 MB 64-bit SDRAM module (D6502A)
128 MB 64-bit SDRAM module (D6503A)
Hard Disk Drive
Slim Floppy Disk Drive
Slim CD-ROM Drive