HP R/T2200 IEC-320-C14 HP UPS R/T3000 G2 Installation Instructions
HP R/T2200 IEC-320-C14 Manual
 |
View all HP R/T2200 IEC-320-C14 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP R/T2200 IEC-320-C14 manual content summary:
- HP R/T2200 IEC-320-C14 | HP UPS R/T3000 G2 Installation Instructions - Page 1
for manual material handling. Kit contents • Important Safety Information guide • This document and/or documentation CD • HP Infrastructure Management Pack CD To download the latest software version, see the HP website (http://www.hp.com/go/rackandpower). • Warranty information • Rails, with - HP R/T2200 IEC-320-C14 | HP UPS R/T3000 G2 Installation Instructions - Page 2
models require a dedicated (unshared) branch circuit, suitably rated for the specific UPS as stated in "Input specifications" in the user guide. Readying the equipment 1. Check the battery . NOTE: If preparing the rails for integrated shipping, follow the same instructions as in "Installing the UPS - HP R/T2200 IEC-320-C14 | HP UPS R/T3000 G2 Installation Instructions - Page 3
bracket using wing nuts. Wait until the unit is installed and the brackets are adjusted before tightening the nuts. 4. Insert screws through the mounting rail into the cage nuts or clip nuts. Installing the UPS in a rack Before installing the unit, review and adhere to all warnings provided in - HP R/T2200 IEC-320-C14 | HP UPS R/T3000 G2 Installation Instructions - Page 4
computer. See the HP website (http://www.hp.com/go/rackandpower) to download the latest version of HP Power Protector. NOTE: To install and configure the software, see the software user guide. The software user guide is available for download from the HP website (http://www.hp.com/go/rackandpower - HP R/T2200 IEC-320-C14 | HP UPS R/T3000 G2 Installation Instructions - Page 5
attached to a single, normally-open contact in a parallel connection. HP recommends using different colors for the positive and negative wires. If a " in the user guide. For information about verifying the REPO connection, see "Verifying the REPO port connection" in the user guide. Connecting the - HP R/T2200 IEC-320-C14 | HP UPS R/T3000 G2 Installation Instructions - Page 6
on using power protector software. • Plug an extension the number of amps by batteries With the UPS in Standby mode, allow the batteries to charge before putting the UPS into service. IMPORTANT: Charge the batteries for at least 24 hours before supplying backup power to devices. The batteries - HP R/T2200 IEC-320-C14 | HP UPS R/T3000 G2 Installation Instructions - Page 7
logo badge Gently pull out the logo badge, rotate it 90 degrees, and then replace it in the bezel. Continuing the installation To continue the UPS installation, follow the instructions starting with "Connecting the serial communications port." Installing the extension bars (if included) Attaching - HP R/T2200 IEC-320-C14 | HP UPS R/T3000 G2 Installation Instructions - Page 8
Connecting and securing the power cords 4. If the UPS is powered up, you can be sure that the UPS Network Module is seated properly and communicating with the UPS by verifying that the UPS Data LED illuminates solid green, and then flashes regularly after 2 minutes. Installing the optional UPS
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
 |
 |
HP UPS R/T3000 G2
Installation Instructions
Overview
The HP UPS R/T3000 G2 features a 2U rack-mount with convertible
tower design and offers power protection for loads up to a maximum of
3300 VA/3000 W (these numbers might vary by model).
For more information about any of the topics covered in this document,
see the UPS user guide located on the documentation CD or HP website
Precautions
WARNING:
To prevent personal injury from earth
conductor leakage current:
•
Do not operate the UPS while disconnected from the
utility power source.
•
Disconnect load devices before disconnecting the UPS
from the utility power source.
37 kg
82 lb
This symbol indicates that the UPS exceeds the
recommended weight for one individual to
handle safely.
WARNING:
To reduce the risk of personal injury
or damage to the equipment, observe local
occupational health and safety requirements and
guidelines for manual material handling.
Kit contents
•
Important Safety Information
guide
•
This document and/or documentation CD
•
HP Infrastructure Management Pack CD
To download the latest software version, see the HP website
•
Warranty information
•
Rails, with mounting hardware
•
Tower conversion stand (2)
•
Front mounting ears (2) and associated hardware
© Copyright 2011 Hewlett-Packard Development Company, L.P.
The information contained herein is subject to change without notice. The only
warranties for HP products and services are set forth in the express warranty
statements accompanying such products and services. Nothing herein should
be construed as constituting an additional warranty. HP shall not be liable for
technical or editorial errors or omissions contained herein.
Part Number: 650953-001
January 2011
Edition: 1