HP R/T3000 UPS R12000 XR Backplate Receptacle Kit Installation Instructions
HP R/T3000 Manual
View all HP R/T3000 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP R/T3000 manual content summary:
- HP R/T3000 | UPS R12000 XR Backplate Receptacle Kit Installation Instructions - Page 1
of the HP Backplate Receptacle Kit. Save these instructions for future reference. NOTE: This kit can only be used with the HP Uninterruptible Power System (UPS) R12000 XR model. Important Safety Information Before installing this product, read the Important Safety Information guide included with - HP R/T3000 | UPS R12000 XR Backplate Receptacle Kit Installation Instructions - Page 2
safety and health regulations for the facility. To power down the UPS: 1. Place the UPS in Refer to the installation instructions for the UPS for more information. Removing the Battery and Electronics Modules 1. module (ERM) connected to the UPS, disconnect the ERM batteries. 1. Remove the ERM bezel - HP R/T3000 | UPS R12000 XR Backplate Receptacle Kit Installation Instructions - Page 3
observe all materials-handling procedures for removing the battery module, which weighs 34 kg (75 lb). 2. Disconnect the input and output wiring. 4. Disconnect the right battery module. 3. Remove the UPS and ERM wiring port covers. 5. Repeat steps 1 through 4 for other ERMs connected to the UPS. - HP R/T3000 | UPS R12000 XR Backplate Receptacle Kit Installation Instructions - Page 4
wiring port cover is not installed. Wiring to the Terminal Block 1. Connect the backplate receptacle option wires. 5. If there is an ERM installed, start the screws. 2. Connect the input wires. 6. Install the backplate receptacle option. Item Description 1 Input wire hole IMPORTANT: Be sure - HP R/T3000 | UPS R12000 XR Backplate Receptacle Kit Installation Instructions - Page 5
not damage the LED power cable when inserting the top battery module. Powering Up the UPS 1. Power on the AC mains at the service panel by closing the switch or circuit breaker. - All LEDs illuminate for three seconds as part of the system initialization. - Each module powers on in sequence (with
hp r12000 xr
backplate receptacle
kit
installation instructions
Read instructions completely before beginning
installation procedure.
© 2003 Hewlett-Packard Development Company, L.P.
Hewlett-Packard Company shall not be liable for technical or editorial errors or
omissions contained herein. The information in this document is provided “as is”
without warranty of any kind and is subject to change without notice. The warranties
for HP products are set forth in the express limited warranty statements
accompanying such products. Nothing herein should be construed as constituting an
additional warranty.
hp r12000 xr backplate receptacle kit installation instructions
First Edition (February 2003)
Part Number 330871-021
330871- 021
Overview
These instructions assist qualified electricians with the installation
of the HP Backplate Receptacle Kit. Save these instructions for
future reference.
NOTE:
This kit can only be used with the HP Uninterruptible Power System
(UPS) R12000 XR model.
Important Safety
Information
Before installing this product, read the
Important Safety
Information
guide included with this kit.
WARNING:
•
The installation of this product must be performed by
individuals who are knowledgeable about the procedures,
precautions, and hazards associated with AC and DC power
products.
•
The backplate receptacle option must be connected directly
to the UPS by a qualified electrician.
•
The connection of the backplate receptacle option to the
terminals of the UPS must be performed by a qualified
electrician.
•
There are no user-serviceable components inside.
Kit Contents
•
Backplate receptacle option
•
Important Safety Information
guide
•
This document
Tools and Materials Required
The following tools are needed:
•
#3 Phillips screwdriver bit
•
Flat-head screwdriver
•
Metric tools
— 7 mm
— 8 mm