HP R1.5 UPS R1500 XR Models Installation Instructions

HP R1.5 Manual

Get HP R1.5 PDF manuals and user guides View all HP R1.5 manuals
Add to My Manuals
Save this manual to your list of manuals

HP R1.5 manual content summary:

  • HP R1.5 | UPS R1500 XR Models Installation Instructions - Page 1
    . HP Uninterruptible Power System R1500 XR Models Installation Instructions Second Edition (August 2002) Part Number 215859-022 Overview These instructions show how to install an uninterruptible power system (UPS). For detailed information about the UPS, refer to the UPS user guide on the Power
  • HP R1.5 | UPS R1500 XR Models Installation Instructions - Page 2
    A NONSPILLABLE BATTERY Next Recharge Date: 14-DEC-04 Please refer to Maintenance Section of Owner's Manual enclosed inside Kit Contents Documentation • International Regulatory Compliance guide • Important Safety Information guide • Power Products Documentation CD • Rack and Power Management Pack CD
  • HP R1.5 | UPS R1500 XR Models Installation Instructions - Page 3
    low-voltage R1500 XR JPN • 15 A for low-voltage R1500 XR NA • 10 A for high-voltage hp.com) to find the total system leakage current. IMPORTANT: If the UPS does not include a suitable power cord, contact an HP authorized service representative to obtain the appropriate power feet are extended to the
  • HP R1.5 | UPS R1500 XR Models Installation Instructions - Page 4
    insert additional screws for support if any screw holes are unoccupied. Completing the UPS Assembly Connecting the Communications Port The UPS includes a communications port that allows the unit to exchange data with the host computer. IMPORTANT: Power management software requires the communications
  • HP R1.5 | UPS R1500 XR Models Installation Instructions - Page 5
    with a standard telephone line only, not with a digital PBX. 4. Replace the connector block in the REPO port. 1 2 Item Description 1 • The remote switch must be in the Off (open) position to enable power to the output receptacles. Connecting the Ground Bonding Screw The ground bonding screw on
  • HP R1.5 | UPS R1500 XR Models Installation Instructions - Page 6
    LEDs. If this does not clear the LEDs, refer to the UPS user guide for more information. Charging the Batteries With the UPS in Standby mode, allow the batteries to charge before putting the UPS into service. IMPORTANT: The battery pack charges to: • 90% of its capacity within 3 hours. • 100% of its
  • HP R1.5 | UPS R1500 XR Models Installation Instructions - Page 7
    the system: 1. Shut down all load devices. 2. Press the Standby button to take the UPS out of Operate mode. Power to the load receptacles ceases. 3. Disconnect the UPS from utility power. 4. Wait at least 60 seconds while the UPS internal circuitry discharges. For more information, refer to the HP
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
hp uninterruptible
power system
R1500 xr models
installation instructions
Read Instructions Completely
Before Beginning Installation Procedures
Hewlett-Packard Company shall not be liable for technical or editorial errors or
omissions contained herein. The information in this document is provided “as is”
without warranty of any kind and is subject to change without notice. The warranties
for HP products are set forth in the express limited warranty statements
accompanying such products. Nothing herein should be construed as constituting an
additional warranty.
HP Uninterruptible Power System R1500 XR Models Installation Instructions
Second Edition (August 2002)
Part Number 215859-022
215859- 022
Overview
These instructions show how to install an uninterruptible power
system (UPS). For detailed information about the UPS, refer to the
UPS user guide on the Power Products Documentation CD.
Important Safety Information
Before installing this product, read the
Important Safety
Information
document provided.
WARNING:
To prevent personal injury from electric shock and
hazardous energy levels, the installation of options and routine
maintenance and service of this product must be performed by
individuals who are knowledgeable about the procedures,
precautions, and hazards associated with AC power products.
WARNING:
To prevent personal injury from earth conductor
leakage current:
•
Do not operate a UPS that is disconnected from the utility
power source.
•
Disconnect protected devices from the UPS before
disconnecting the UPS from utility power.
•
Use the Test/Alarm Reset button to test the batteries rather
than unplugging the UPS. Refer to the UPS user guide for
more information on the operation of the UPS.
Regulatory Compliance
Identification Numbers
For regulatory compliance certifications and identification
purposes, the UPS models are assigned a series number, also
identified on the Regulatory Compliance label located on the
side of the UPS. For certification information, always refer to
the series number:
•
R1500 XR NA series number: EO3008
•
R1500 XR JPN series number: EO3008j
•
R1500 XR H INT’L series number: EO3008i
NOTE:
The rating label on the device provides the class (A or B) of the
equipment. Class B devices have a Federal Communications Commission
(FCC) logo or FCC ID on the label. Class A devices do not have an FCC logo
or FCC ID on the label. After you determine the class of the device, refer to
the UPS user guide for complete regulatory compliance notices.
Weight
24 kg
52 lb
WARNING:
The UPS weighs 24 kg (52 lb) when fully
assembled. To prevent personal injury or damage to
the equipment:
•
Observe local occupational health and safety
requirements and guidelines for manual material
handling.
•
Obtain adequate assistance to lift and stabilize the
product during installation or removal. The UPS is
unstable when not fastened to the rails.
•
Remove the battery pack to reduce the overall
weight of the product.