HP StoreVirtual 4000 HP LeftHand 4330 10 GbE SFP+ Installation Instructions
HP StoreVirtual 4000 Manual
View all HP StoreVirtual 4000 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP StoreVirtual 4000 manual content summary:
- HP StoreVirtual 4000 | HP LeftHand 4330 10 GbE SFP+ Installation Instructions - Page 1
GbE board. 4. Configure bonds. 5. Change the SAN/iQ interface (under the storage system Network category, on the Communication tab) to bond configured using 10 GbE ports (NICSlot1:Port1 & 2). 6. Prepare the host server. The 10 GbE feature option adds 10 GbE to the HP StoreVirtual 4330 platform. This - HP StoreVirtual 4000 | HP LeftHand 4330 10 GbE SFP+ Installation Instructions - Page 2
group) Check the following items before starting the migration: • Have compatible VIP addresses for the 10 GbE switches that are running the 10 GbE ALB and bonds listed on the selected storage system's Network category TCP/IP tab window before installing and configuring the 10 GbE adapter. Table - HP StoreVirtual 4000 | HP LeftHand 4330 10 GbE SFP+ Installation Instructions - Page 3
NIC IP address VIP address If bonds are configured: Bond0 IP address Bond1 IP address If bonds are not configured: FlexLOM:Port1 IP address FlexLOM:Port2 IP address FlexLOM:Port3 IP address FlexLOM:Port4 IP address Table 6 During upgrade, use this storage system information Bond0 IP address to - HP StoreVirtual 4000 | HP LeftHand 4330 10 GbE SFP+ Installation Instructions - Page 4
the risk of personal injury or equipment damage, be sure that the rack is adequately stabilized before extending a component from the rack. 3. Remove the storage system from the rack and place it on a sturdy, level surface. 4. To remove the access panel, open the locking latch, slide the access - HP StoreVirtual 4000 | HP LeftHand 4330 10 GbE SFP+ Installation Instructions - Page 5
IP Address, and manually assign an available IP address If you are prompted with the following message, click OK to continue. The condition described is not actually true. The storage system's IP address, 0.0.0.0, is not reachable by the cluster's Virtual IP (VIP). Change the storage system's IP - HP StoreVirtual 4000 | HP LeftHand 4330 10 GbE SFP+ Installation Instructions - Page 6
. 4. Add the bond IP address to the Find Systems list and rediscover this storage system. NOTE: Delete the existing IP address that was being used to discover this storage system. 5. The Storage Server service on this storage system will restart to allow the networking changes to take effect. Wait
HP StoreVirtual 4330 Storage
10 GbE SFP+ Installation
Instructions
Abstract
This document describes how to install the 10 Gigabit
Ethernet (GbE) SFP+ for the HP StoreVirtual 4330. Note
that the HP 4330 FC ships with the 10 GbE SFP+ installed.
If you need to replace the 10 GbE SFP+ in either the HP
4330 or HP 4330 FC, you can use the instructions in this
document.
© Copyright 2012 Hewlett-Packard Development Company, L.P.
*BQ891-96004*
HP Part Number: BQ891-96004
Published: November 2012
Edition: 1
Overview
Instructions vary depending on whether this is an
upgrade
(the 4330 is new and/or not in a
management group) or a
migration
(the 4330 is
already in a management group).
For an upgrade, the steps are:
1.
Install the 10 GbE board.
2.
Configure the 10 GbE ports.
3.
Configure bonds.
4.
Change the SAN/iQ interface (under the storage
system Network category, on the Communication
tab) to
bond configured
using 10 GbE ports
(NICSlot1:Port1 & 2).
For a migration, the steps are:
1.
Plan for the migration.
2.
Shut down the management group.
3.
Install the 10 GbE board.
4.
Configure bonds.
5.
Change the SAN/iQ interface (under the storage
system Network category, on the Communication
tab) to
bond configured
using 10 GbE ports
(NICSlot1:Port1 & 2).
6.
Prepare the host server.
The 10 GbE feature option adds 10 GbE to the HP
StoreVirtual 4330 platform. This is an add-on feature
to the 1 Gb 4 port FlexLOM module installed on the
system motherboard of the 4330 storage systems. After
the 10 GbE dual port Ethernet adapter is installed and
configured, users see six Ethernet interfaces listed in
the Centralized Management Console in the storage
system Network category, on the TCP/IP tab window
(four for 1 GbE and two for 10 GbE). These six
Ethernet interfaces can be bonded a number of ways.
The CMC reports the network interface names of these
six Ethernet interfaces as noted in
Table 1 (page 1)
.
Table 1
Port name in the CMC
NIC type
FlexLOM:Port1
1 GbE
FlexLOM:Port2
1 GbE
FlexLOM:Port3
1 GbE
FlexLOM:Port4
1 GbE
NICSlot1:Port1
10 GbE
NICSlot1:Port2
10 GbE
When upgrading to 10 GbE on storage systems that
have bonded NICs and are already in a cluster and
Page 1