HP Surestore Tape Library Model 20/700 Expansion Frame Installation Guide
HP Surestore Tape Library Model 20/700 Manual
View all HP Surestore Tape Library Model 20/700 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP Surestore Tape Library Model 20/700 manual content summary:
- HP Surestore Tape Library Model 20/700 | Expansion Frame Installation Guide - Page 1
guides do not address. Please remind the customer that the latest user documentation is available from the HP Customer Care website: http://www.hp.com/go/ support down and power on procedures, as described in the Installation or Service Manual. • If you install or replace an Expansion Module you must - HP Surestore Tape Library Model 20/700 | Expansion Frame Installation Guide - Page 2
s Expansion Frame Install 1. Have the operator take the library and all drives offline and power off the tape library. 2. Obtain key and open cartridge area door. CAUTION: Lifting hazard. Two people are required to remove the rear cover. 3. Remove the right rear cover (cover with window) by - HP Surestore Tape Library Model 20/700 | Expansion Frame Installation Guide - Page 3
Figure 1. Removing Right Rear Cover (Continued) Removing Right Rear Cover (a5605a_01) 1. Rear Cover 2. Mushroom (6x) 3. Lock-Down Latch Tool 4. Lock-Down Latch 5. Mushroom (Ref) 6. Mushroom (Ref) 4. Slide cover up and set aside. 5. Using a T30 Torx driver, remove the mushrooms from the tape library - HP Surestore Tape Library Model 20/700 | Expansion Frame Installation Guide - Page 4
Figure 2. Theta Stop and Mounting Holes Theta Stop and Mounting Holes (a5605a_02) 1. Mounting Hole Locations 2. Remove Theta Stop 3. Mounting Hole Locations 4. Measure the distance from the floor to the inside floor of library 5. Front Left Plate 62108 4 - HP Surestore Tape Library Model 20/700 | Expansion Frame Installation Guide - Page 5
CAUTION: Heavy Load. At least three people are required to remove the Expansion Frame from packaging and push it into position. 12. Remove the expansion frame from its package and place it flat on the floor. 13. Measure the distance from the floor of the room to the inside floor of the tape library - HP Surestore Tape Library Model 20/700 | Expansion Frame Installation Guide - Page 6
Figure 3. Expansion Frame Alignment Expansion Frame Alignment (a5605a_03) 1. Top Locating Pin 2. 1/4-20 x 1/2-in. Torx Screw (6x) 3. Expansion Frame 4. Leveling Bolt (4x) 5. Bottom Locating Pin CAUTION: Be careful not to hit your head on the theta lock down bracket mounted to the top inside surface - HP Surestore Tape Library Model 20/700 | Expansion Frame Installation Guide - Page 7
20. Replace the arrays, the array retainer clips, and cartridges removed in Step 7 back to Panel 2, Column 3 and 4. 21. Close the tape library doors and lock. 22. Power the tape library on and verify that it initializes and audits properly. 23. Return unit to customer. 62108 7 - HP Surestore Tape Library Model 20/700 | Expansion Frame Installation Guide - Page 8
62108 REV C EC 111700A Copyright ©2002 Hewlett-Packard Company/ Storage Technology Corp Edition 1/2002
62108
1
HP Surestore Tape Library 20/700
A5605A Expansion Frame Installation Guide
(for HP field service use only)
CAUTION:
The HP tape library Expansion Frame is not customer installable or
replaceable.
Any servicing, adjustment, maintenance or repair must be performed only
by authorized HP service-trained personnel.
Note to Customer Engineer:
This installation may add new technology to the library
that older user’s guides do not address.
Please remind the customer that the latest user
documentation is available from the HP Customer Care website:
support
.
■
Materials Included
■
Installation Notes
•
Confirm with the customer System Administrator that the tape library can be powered
off.
•
Observe proper power down and power on procedures, as described in the
Installation
or
Service Manual.
•
If you install or replace an Expansion Module you must check mark the appropriate
box on the Drive Location Label. The Drive Location Label is located on the inside of
the library door, just below the UL label.
•
Heavy Load
. At least three people are required to remove the Expansion Frame from
packaging and push it into position.
Tools Required
Prior to beginning the installation process, obtain the following tools:
•
1/4-inch Ratchet Wrench
Table 1. Materials List
Part
Quantity
I/I Expansion Frame
1
Expansion Frame Assembly
1
1/4-20 x 1/2-in. Torx Screws
6
Lock Down Latch Tool
1