HP T1500 IEC-320-C14 HP Uninterruptible Power System T700 Models Installation
HP T1500 IEC-320-C14 Manual
View all HP T1500 IEC-320-C14 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP T1500 IEC-320-C14 manual content summary:
- HP T1500 IEC-320-C14 | HP Uninterruptible Power System T700 Models Installation - Page 1
HP Uninterruptible Power System T700 Models Installation Instructions Second Edition (August 2002) Part Number 215398-022 Overview These instructions service batteries rather than unplugging the UPS. Refer to the UPS user guide • T700 NA series number: EO3016 • T700 JPN series number: manual material - HP T1500 IEC-320-C14 | HP Uninterruptible Power System T700 Models Installation - Page 2
an HP authorized service representative for directions. NOTE: The following label is only an example date. The date on your carton may be different. THIS PRODUCT CONTAINS A NONSPILLABLE BATTERY Next Recharge Date: 14-DEC-04 Please refer to Maintenance Section of Owner's Manual enclosed inside - HP T1500 IEC-320-C14 | HP Uninterruptible Power System T700 Models Installation - Page 3
General Alarm/Overload 2 On Battery/Low Battery 5 Test/Alarm Reset button 3 Bad Battery 6 On/Standby button a self-test. Refer to the UPS user guide for more information on the front panel LED display the front panel LEDs are amber or red (indicating an alarm condition), press the Test/Alarm - HP T1500 IEC-320-C14 | HP Uninterruptible Power System T700 Models Installation - Page 4
With the UPS in Standby mode, allow the batteries to charge before putting the UPS into service. IMPORTANT: The battery pack charges to: • 90% of its capacity within 3 hours. • 100% of its capacity within 24 hours. Charge the batteries for at least 24 hours before supplying backup power to the
hp uninterruptible
power system
T700 models
installation instructions
Read Instructions Completely
Before Beginning Installation Procedures
Hewlett-Packard Company shall not be liable for technical or editorial errors or
omissions contained herein. The information in this document is provided “as is”
without warranty of any kind and is subject to change without notice. The warranties
for HP products are set forth in the express limited warranty statements
accompanying such products. Nothing herein should be construed as constituting an
additional warranty.
HP Uninterruptible Power System T700 Models Installation Instructions
Second Edition (August 2002)
Part Number 215398-022
215398- 022
Overview
These instructions show how to install an uninterruptible power
system (UPS). For detailed information about the UPS, refer to the
UPS user guide on the Power Products Documentation CD.
Important Safety Information
Before installing this product, read the
Important Safety
Information
document provided.
WARNING:
To prevent personal injury from electric shock and
hazardous energy levels, the installation of options and routine
maintenance and service of this product must be performed by
individuals who are knowledgeable about the procedures,
precautions, and hazards associated with AC power products.
WARNING:
To prevent personal injury from earth conductor
leakage current:
•
Do not operate a UPS that is disconnected from the utility
power source.
•
Disconnect protected devices from the UPS before
disconnecting the UPS from utility power.
•
Use the Test/Alarm Reset button to test the batteries rather
than unplugging the UPS. Refer to the UPS user guide for
more information on the operation of the UPS.
Regulatory Compliance
Identification Numbers
For the purpose of regulatory compliance certifications and
identification, the UPS models are assigned series numbers, also
identified on the Regulatory Compliance label located on the rear
of the UPS. For certification information, refer to the series
number:
•
T700 NA series number:
EO3016
•
T700 JPN series number:
EO3016j
•
T700 H INT’L series number:
EO3016i
NOTE:
The rating label on the device provides the class (A or B) of the
equipment. Class B devices have a Federal Communications Commission
(FCC) logo or FCC ID on the label. Class A devices do not have an FCC logo
or FCC ID on the label. After you determine the class of the device, refer to
the UPS user guide for complete regulatory compliance notices.
Weight
12 kg
27 lb
WARNING:
The UPS weighs 12 kg (27 lb) when fully
assembled. To prevent personal injury or damage to
the equipment:
•
Observe local occupational health and safety
requirements and guidelines for manual material
handling.
•
Obtain adequate assistance to lift and stabilize the
UPS during installation or removal.