HP Workstation x2000 hp workstation x2000 - Accessory Installation Guide
HP Workstation x2000 Manual
View all HP Workstation x2000 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP Workstation x2000 manual content summary:
- HP Workstation x2000 | hp workstation x2000 - Accessory Installation Guide - Page 1
hp x2000 workstation accessory installation guide - HP Workstation x2000 | hp workstation x2000 - Accessory Installation Guide - Page 2
- HP Workstation x2000 | hp workstation x2000 - Accessory Installation Guide - Page 3
Accessory Installation Guide HP x2000 Workstation Manufacturing Part Number: A7218-90010 Edition E0501 © Copyright 2001 Hewlett-Packard Company. - HP Workstation x2000 | hp workstation x2000 - Accessory Installation Guide - Page 4
particular purpose. Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in , Direct RDRAM and RIMM are trademarks of Rambus, Inc. Printing History The manual printing date and part number indicate its current edition. The printing date will - HP Workstation x2000 | hp workstation x2000 - Accessory Installation Guide - Page 5
Drives 19 Verifying Your IDE Drive 20 Installing SCSI Drives 20 Before Installing a SCSI Hard Disk 21 Verifying Your SCSI Drive 22 Additional Guide Rails 23 Removing and Replacing a Hard Disk Drive 24 Removing the Old Drive 24 Installing the New Drive 25 Installing a Second Hard Disk Drive - HP Workstation x2000 | hp workstation x2000 - Accessory Installation Guide - Page 6
Contents Replacing the Processor 33 Removing the Existing Processor 33 Installing the New Processor 34 Replacing the Battery 35 System Board Connector Diagram 37 4 - HP Workstation x2000 | hp workstation x2000 - Accessory Installation Guide - Page 7
disk drive Secondary Hard Disk Drive Shelf Primary Hard Disk Drive Shelf Chassis Beam Contact your dealer for an up-to-date list of supported devices or check the HP web site: www.hp.com/workstations. WARNING To avoid electrical shock, do not open the power supply. There are no user-serviceable - HP Workstation x2000 | hp workstation x2000 - Accessory Installation Guide - Page 8
information only • x2000 Getting Started Guide - basic information only • The x2000 Technical Reference -- for complete information on the web at www.hp.com/workstations/support Go to www.hp.com/workstations/support - for downloadable documentation, drivers & utilities, service & support options 6 - HP Workstation x2000 | hp workstation x2000 - Accessory Installation Guide - Page 9
Characteristics Weight (configuration with one CD-ROM drive, excluding keyboard and display) Dimensions Footprint Acoustic noise emission (ISO 7779) Operating (idle): Power Supply Input voltage Input frequency: Maximum output power: Power consumption Storage Humidity HP X2000 Workstation 14 - HP Workstation x2000 | hp workstation x2000 - Accessory Installation Guide - Page 10
8 - HP Workstation x2000 | hp workstation x2000 - Accessory Installation Guide - Page 11
1 Installing and Replacing Accessories Chapter 1 9 - HP Workstation x2000 | hp workstation x2000 - Accessory Installation Guide - Page 12
your computer using its on/off switch, then remove its power cord before removing the Workstation's cover. Remove the Power Protection Device cables before any servicing operation. Always replace the cover before switching the Workstation on again. Removing the Cover 1. Switch off the display and - HP Workstation x2000 | hp workstation x2000 - Accessory Installation Guide - Page 13
Figure 1-1 Installing and Replacing Accessories Removing and Replacing the Cover and Front Bezel Removing the Cover 4 3 2 WARNING NOTE Parts inside the computer may be hot, wait for them to cool before touching them. Removing the Front Bezel The front bezel is divided into two sections: • The - HP Workstation x2000 | hp workstation x2000 - Accessory Installation Guide - Page 14
the Workstation, lower the cover onto the chassis (aligning the guide rail on the guides on the top of the cover slide into the rails at the top of the chassis. 5. Slide the cover forward, then tighten the two thumbscrews. 6. If required, lock the cover using the key provided. Reconnect all the power - HP Workstation x2000 | hp workstation x2000 - Accessory Installation Guide - Page 15
BB2 B1 A2 A1 Power Supply Connector Processor Secondary IDE Primary IDE Floppy If only two RDRAM modules are installed, use the sockets marked A1 and B1. The other two sockets (A2 and B2) must contain continuity modules. Use only HP memory modules designed for your Workstation model. For other - HP Workstation x2000 | hp workstation x2000 - Accessory Installation Guide - Page 16
and Upgrading Memory Removing and Replacing a Memory Module 1. Switch off the display and Workstation. Disconnect all power cables and any LAN or telecommunications cables. 2. Remove the Workstation's cover (refer to page 10 for instructions). To ease installation, place the Workstation on its - HP Workstation x2000 | hp workstation x2000 - Accessory Installation Guide - Page 17
HP x2000 Workstation has five 32-bit 33 MHz Workstation (Workstation 2.2) accessory card slots and one AGP PRO slot on the system board. x2000 models support the following AGP graphics cards: • 1.5V AGP graphics cards (≤ 25W) • 1.5V AGP PRO graphics cards (≤ 50W) The x2000 does not support high power - HP Workstation x2000 | hp workstation x2000 - Accessory Installation Guide - Page 18
that holds the old card in place and carefully pull it out. NOTE Some cards may have preferred locations and special installation instructions detailed in their manuals. 5. Aligning the new card carefully, slide it into position, then press it firmly into the slot and tighten the retaining screw - HP Workstation x2000 | hp workstation x2000 - Accessory Installation Guide - Page 19
to for the location of the system board connectors). 8. Install any other accessories before replacing the cover (refer to page 12). Reconnect all cables and power cords. Chapter 1 17 - HP Workstation x2000 | hp workstation x2000 - Accessory Installation Guide - Page 20
to two hard disk drives in the x2000 chassis. The internal hard disk shelves support up to two 15 Krpm drives. Identifying Cables and Connectors (all models) If you add an IDE Zip drive, hard disk drive, DVD drive, CD-ROM drive, CD-RW drive, or tape drive, you need to connect it to power and data - HP Workstation x2000 | hp workstation x2000 - Accessory Installation Guide - Page 21
Before installing an IDE Hard disk, refer to the drive's installation guide to check jumper settings or if there is a special installation procedure to follow. There are three or four data cables inside your Workstation. Two of these are for IDE devices. • The ATA IDE cable supports two IDE devices - HP Workstation x2000 | hp workstation x2000 - Accessory Installation Guide - Page 22
Drive 1. Switch on the computer. 2. To verify the configuration of your hard disk drive, press F2 to enter Setup when the HP BIOS will detect that the device is missing. Press F4 to confirm that you want to remove the device. The system configuration will be updated automatically. Installing SCSI Drives - HP Workstation x2000 | hp workstation x2000 - Accessory Installation Guide - Page 23
Workstation SCSI Card in WorkstationI Slot Secondary IDE Connector Cable with one 34-pin connector for 3.5-inch Floppy Disk Drive Floppy Disk Drive for wide 16-bit SCSI. SCSI ID 0 is used by the first SCSI hard disk drive and SCSI ID 7 is reserved for the integrated SCSI controller (the default for - HP Workstation x2000 | hp workstation x2000 - Accessory Installation Guide - Page 24
Configuration Utility press Ctrl-C when prompted during the Workstation's start-up routine. 3. Verify or modify the configuration of your new SCSI hard disk drive. For more information on configuring a SCSI hard disk drive, refer to the SCSI User's Guide. 4. When configuration is complete, exit the SCSI - HP Workstation x2000 | hp workstation x2000 - Accessory Installation Guide - Page 25
Additional Guide Rails Extra guide rails are supplied for the installation of additional mass storage devices. These are inside the Workstation, three 3.5-inch device (2nd hard disk drive) 5.25-inch device (CD-ROM, DVD, etc.) 3.5-inch device (zip drive or second floppy disk drive ) Location 3.5-inch - HP Workstation x2000 | hp workstation x2000 - Accessory Installation Guide - Page 26
1. Switch off the display and Workstation. Disconnect all power cables and any LAN or telecommunications cables. 2. Remove the Workstation's cover (refer to page 11 for instructions). 3. Disconnect the data and power cables from the hard disk drive. 4. Remove the drive. To do this, press the two - HP Workstation x2000 | hp workstation x2000 - Accessory Installation Guide - Page 27
cable to the new hard disk drive. The connectors are shaped to go in one way only. If you are not sure which connector to use, refer to "Mass Storage and Optical Device Overview" on page 18. 5. Replace the Workstation's cover (refer to page 12). Reconnect all the power and telecommunications cables - HP Workstation x2000 | hp workstation x2000 - Accessory Installation Guide - Page 28
drive, can support two 3.5-inch devices. To install a second hard disk drive: 1. Switch off the display and Workstation. Disconnect all power cables and any LAN or telecommunications cables. 2. Remove the Workstation's cover (refer to page 11 for instructions). 3. If the boot IDE hard disk drive - HP Workstation x2000 | hp workstation x2000 - Accessory Installation Guide - Page 29
Device in a Front Access Bay 1. Switch off the display and Workstation. Disconnect all power cables and any LAN or telecommunications cables. 2. Remove the Workstation's cover and front upper bezel (refer to page 10 for instructions). 3. Depending on the device to be installed, either: a. Remove the - HP Workstation x2000 | hp workstation x2000 - Accessory Installation Guide - Page 30
Access Bay Attaching the Rails and Installing the Drive 4 5 Figure 1-10 5. Connect the power and data cables to the installed device. The Filler 7. Replace the front upper bezel and Workstation's cover (refer to page 12). Reconnect all the power and telecommunications cables. 8. Turn to page 29 - HP Workstation x2000 | hp workstation x2000 - Accessory Installation Guide - Page 31
Configuration Utility press Ctrl-C when prompted during the Workstation's start-up routine. 2. Verify or modify the configuration of your new SCSI hard disk drive. For more information on configuring a SCSI hard disk drive, refer to the SCSI User's Guide. 3. When configuration is complete, exit the SCSI - HP Workstation x2000 | hp workstation x2000 - Accessory Installation Guide - Page 32
Workstation's cover and front upper bezel (refer to page 10 for instructions). 3. Disconnect the power and data cables from the old drive. 4. Remove the drive. To do this, press the two front clips inward and, pushing from the rear, slide out the drive. See Figure 1-11. 5. Remove the two green guide - HP Workstation x2000 | hp workstation x2000 - Accessory Installation Guide - Page 33
software for the 12X/8X/32X CD-RW drive that is installed in your HP x2000 Workstation is not included in the pre-loaded software. You must install the Direct CD and Easy CD Creator applications manually from the Applications CD-ROM (provided with the Workstation or as an accessory kit) before you - HP Workstation x2000 | hp workstation x2000 - Accessory Installation Guide - Page 34
Installing and Replacing Accessories Replacing the CD-ROM Drive (or DVD-Drive) use the full functionality of the CD-RW drive. If you do not install these two software packages, you can only use the CD-RW drive's read functionality. 32 Chapter 1 - HP Workstation x2000 | hp workstation x2000 - Accessory Installation Guide - Page 35
heatsink may become too hot to touch. Switch off the display and Workstation. 2. Disconnect all power cables and any LAN or telecommunications cables and remove the Workstation's cover (refer to page 10 for instructions). 3. Place the Workstation on its side for better access. 4. Remove the heatsink - HP Workstation x2000 | hp workstation x2000 - Accessory Installation Guide - Page 36
Figure 1-13 Installing and Replacing Accessories Replacing the Processor 6. Open the Zero Insertion Force (ZIF) lever, located at the side of the processor socket, until it is in the vertical position (depending on the socket design, the handle may need to go past vertical), then carefully lift out - HP Workstation x2000 | hp workstation x2000 - Accessory Installation Guide - Page 37
power connector to the system board. 6. Replace the Workstation's cover (refer to page 12 for instructions). Reconnect all the power and telecommunications cables. When the Workstation the dealer from whom you purchased your Workstation, or to HP, so that they can be either recycled or disposed of in - HP Workstation x2000 | hp workstation x2000 - Accessory Installation Guide - Page 38
with a CR2032 coin type manganese/lithium battery, available from most Workstation stores. To change the battery: 1. Disconnect the Workstation's power supply cord and any connection to a telecommunications network. 2. Remove the Workstation's cover (refer to page 10). 3. Remove the old battery by - HP Workstation x2000 | hp workstation x2000 - Accessory Installation Guide - Page 39
Accessories System Board Connector Diagram Main Power Supply Figure 1-17 System Board Connector Diagram Memory slots System Board Connectors Main chassis fan BB22 B1 A2 A1 Auxiliary power Processor Processor fan CD-ROM audio in Chassis intrusion ATX12V power AGP Slot Secondary IDE Primary - HP Workstation x2000 | hp workstation x2000 - Accessory Installation Guide - Page 40
Installing and Replacing Accessories System Board Connector Diagram 38 Chapter 1 - HP Workstation x2000 | hp workstation x2000 - Accessory Installation Guide - Page 41
- HP Workstation x2000 | hp workstation x2000 - Accessory Installation Guide - Page 42
Part Number A7218-90010 Printed in U.S.A. E0501
hp x2000 workstation
accessory installation guide