Hikvision DS-2CD2083G0-I User Manual

Hikvision DS-2CD2083G0-I Manual

Get Hikvision DS-2CD2083G0-I PDF manuals and user guides View all Hikvision DS-2CD2083G0-I manuals
Add to My Manuals
Save this manual to your list of manuals

Hikvision DS-2CD2083G0-I manual content summary:

  • Hikvision DS-2CD2083G0-I | User Manual - Page 1
    Network Camera User Manual Network Camera User Manual UD09650B 0
  • Hikvision DS-2CD2083G0-I | User Manual - Page 2
    written permission of Hikvision. Unless otherwise stipulated, Hikvision does not make any warranties, guarantees or representations, express or implied, regarding to the Manual. About this Manual This Manual is applicable to Network Camera. The Manual includes instructions for using and managing
  • Hikvision DS-2CD2083G0-I | User Manual - Page 3
    OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED. SURVEILLANCE LAWS VARY BY set up camera time manually. Visit the camera and enter system setting interface for time setting. Safety Instruction These instructions are intended to ensure
  • Hikvision DS-2CD2083G0-I | User Manual - Page 4
    User Manual The convenient supply interruption.  Please make sure that the ceiling can support more than 50(N) Newton gravities if the camera is fixed to the nearest service center. Never attempt to disassemble the camera yourself. (We shall not assume any responsibility for problems caused by
  • Hikvision DS-2CD2083G0-I | User Manual - Page 5
    Network Camera User Manual  Make sure the power supply voltage is correct before using the in hazard of explosion. Please use the manufacturer recommended battery type. Notes: For the camera supports IR, you are required to pay attention to the following precautions to prevent IR reflection: 
  • Hikvision DS-2CD2083G0-I | User Manual - Page 6
    Network Camera User Manual body so that the foam ring and the dome cover are attached seamlessly. 5
  • Hikvision DS-2CD2083G0-I | User Manual - Page 7
    Network Camera User Manual Table of Contents Chapter 1 System Requirement 10 Chapter 2 Network Connection Live View 35 Live View Page 35 Starting Live View 36 Recording and Capturing Pictures Manually 37 Operating PTZ Control 37 PTZ Control Panel...37 Setting/Calling a Preset 39 Setting/
  • Hikvision DS-2CD2083G0-I | User Manual - Page 8
    Network Camera User Manual Maintenance 51 Upgrade & Maintenance 51 Log ...52 System Service ...53 Security Settings 54 Authentication ...54 IP Address Filter ...55 Security Service...56 User Management 57 User Management ...57 Security Question ...59 Online Users...60 Chapter 7 Network Settings
  • Hikvision DS-2CD2083G0-I | User Manual - Page 9
    Network Camera User Manual Configuring Display Settings 95 Day/Night Auto-Switch 95 Day/Night Scheduled-Switch 99 Configuring OSD Settings 100 Configuring Privacy Mask 102 Configuring Picture Overlay
  • Hikvision DS-2CD2083G0-I | User Manual - Page 10
    Network Camera User Manual Chapter 12 Playback 169 Chapter 13 Picture 171 Chapter 14 Application 172 Face Capture Statistics 172 People Counting Statistics 172 Heat Map Statistics 173 Counting
  • Hikvision DS-2CD2083G0-I | User Manual - Page 11
    Network Camera User Manual Chapter 1 System Requirement Operating System Microsoft Windows XP SP1 and above version CPU 2.0 GHz or higher RAM 1G or higher Display 1024×768 resolution or
  • Hikvision DS-2CD2083G0-I | User Manual - Page 12
    Network Camera User Manual Chapter 2 Network Connection Note:  You shall acknowledge that the recommend you to have the network camera assessed and maintained termly. You can contact us if you need such service. Before you start:  If you want to set the network camera via a LAN (Local Area Network
  • Hikvision DS-2CD2083G0-I | User Manual - Page 13
    Network Camera User Manual computer with a network cable as shown in Figure 2-1.  Refer to the use the camera. Activation via Web Browser, Activation via SADP, and Activation via Client Software are all supported.  Activation via Web Browser Steps: 1. Power on the camera, and connect the camera to
  • Hikvision DS-2CD2083G0-I | User Manual - Page 14
    Network Camera User Manual to search the IP address. Activation via Web Browser 3. Create and via SADP Software SADP software is used for detecting the online device, activating the camera, and resetting the password. Get the SADP software from the supplied disk or the official website, and install
  • Hikvision DS-2CD2083G0-I | User Manual - Page 15
    Note: The SADP software supports activating the camera in batch. Refer to the user manual of SADP software for reset your password regularly, especially in the high security system, resetting the password monthly or weekly can better protect your product. Note: You can enable the Hik-Connect service
  • Hikvision DS-2CD2083G0-I | User Manual - Page 16
    Input the admin password and click Modify to activate your IP address modification. The batch IP address modification is supported by the SADP. Refer to the user manual of SADP for details.  Activation via Client Software The client software is versatile video management software for multiple kinds
  • Hikvision DS-2CD2083G0-I | User Manual - Page 17
    the figure below. Network Camera User Manual Control Panel 2. Click the Device Management icon to enter the Device Management interface, as shown in the figure below. 16
  • Hikvision DS-2CD2083G0-I | User Manual - Page 18
    Network Camera User Manual Device Management Interface 3. Check the device status from the device to increase the security of your product. We recommend you reset your password regularly, especially in the high security system, resetting the password monthly or weekly can better protect your product
  • Hikvision DS-2CD2083G0-I | User Manual - Page 19
    Network Camera User Manual Activation Interface (Client Software) 6. Click OK button to start activation. 7. Click to the same subnet with your computer by either modifying the IP address manually or checking the checkbox of Enable DHCP. 9. Input the password to activate your IP address modification.
  • Hikvision DS-2CD2083G0-I | User Manual - Page 20
    Network Camera User Manual (Optional) Setting Security Question Security question is used to reset the admin Static IP Connection Before you start: Please apply a static IP from an ISP (Internet Service Provider). With the static IP address, you can connect the network camera via a router or
  • Hikvision DS-2CD2083G0-I | User Manual - Page 21
    Network Camera User Manual 5. Visit the network camera through a web browser or the client software over the internet. Accessing the Camera through Router with Static IP  Connecting the network
  • Hikvision DS-2CD2083G0-I | User Manual - Page 22
    Network Camera User Manual with port mapping. Note: applied domain name.  Connecting the network camera via a modem Purpose: This camera supports the PPPoE auto dial-up function. The camera gets a public IP address by problem.  Normal Domain Name Resolution Steps: Normal Domain Name Resolution
  • Hikvision DS-2CD2083G0-I | User Manual - Page 23
    Network Camera User Manual 1. Apply a domain name from a domain name provider. 2. Configure the DDNS settings in the DDNS Settings interface of the network camera. Refer to Section 7.1.2 Configuring DDNS Settings for detailed configuration. 3. Visit the camera via the applied domain name. 22
  • Hikvision DS-2CD2083G0-I | User Manual - Page 24
    Network Camera User Manual Chapter 3 Access to the Network Camera Accessing by Web Browsers Note: For certain camera models, HTTPS is enabled by default and the camera creates an
  • Hikvision DS-2CD2083G0-I | User Manual - Page 25
    Network Camera User Manual 4. Click Login. 5. (Optional) Install the plug-in before viewing the live video and operating the camera. Follow the installation prompts to install the plug-in
  • Hikvision DS-2CD2083G0-I | User Manual - Page 26
    Network Camera User Manual iVMS-4200 Main View 25
  • Hikvision DS-2CD2083G0-I | User Manual - Page 27
    Network Camera User Manual Chapter 4 Wi-Fi Settings Purpose: By connecting to the wireless -Fi module. Configuring Wi-Fi Connection in Manage and Ad-hoc Modes Purpose: Two connection modes are supported. Choose a mode as desired and perform the steps to configure the Wi-Fi. Wireless Connection in
  • Hikvision DS-2CD2083G0-I | User Manual - Page 28
    Network mode as Manage, and the Security mode of the network is automatically shown when you select the wireless network, please don't change it manually. Note: These parameters are exactly identical with those of the router. 5. Enter the key to connect the wireless network. The key should be that
  • Hikvision DS-2CD2083G0-I | User Manual - Page 29
    Network Camera User Manual 2. Customize a SSID for the camera. 3. Choose the Security Mode of the wireless connection. 4. Enable the wireless connection function for your PC. 5. On the PC side,
  • Hikvision DS-2CD2083G0-I | User Manual - Page 30
    Network Camera User Manual WEP Mode  Authentication - Select Open or Shared Key types available depend on the access point being used. The following options are available: HEX - Allows you to manually enter the hex key. ASCII - In this method the string must be exactly 5 characters for 64-bit
  • Hikvision DS-2CD2083G0-I | User Manual - Page 31
    Network Camera User Manual Choose the type of client/server authentication being used by the access point; EAP-TLS or EAP-PEAP. EAP-TLS EAP-TLS  Identity - Enter the
  • Hikvision DS-2CD2083G0-I | User Manual - Page 32
    Network Camera User Manual strongly recommend the use of strong passwords for all functions and network devices. The password should be something of your own choosing (using a minimum of 8
  • Hikvision DS-2CD2083G0-I | User Manual - Page 33
    Manual of to enable WPS. 2. Choose the connection mode as PBC. Note: Support of this mode is mandatory for both the Access Points and the connecting devices of the router is enabled. For detailed operation, please see the user guide of the router. 4. Push the WPS button to enable the function
  • Hikvision DS-2CD2083G0-I | User Manual - Page 34
    Network Camera User Manual Use PIN Code If the PIN code is generated from the router side, you should enter the PIN code you get from the router side
  • Hikvision DS-2CD2083G0-I | User Manual - Page 35
    Network Camera User Manual Setting WLAN Parameters 3. Customize the IPv4 address, the IPv4 Subnet Mask and the Default Gateway. The setting procedure is the same with that of LAN. If you want to be assigned the IP address you can check the checkbox to enable the DHCP. 34
  • Hikvision DS-2CD2083G0-I | User Manual - Page 36
    Network Camera User Manual Chapter 5 Live View Live View Page Purpose: The live view page allows you to view the real-time video, capture images, realize PTZ control, set/
  • Hikvision DS-2CD2083G0-I | User Manual - Page 37
    Network Camera User Manual For IE (Internet Explorer) users, plug-ins as webcomponents and quick time are selectable. And for Non-IE users, webcomponents, quick time, VLC or MJPEG are selectable if they are supported by the web browser. Note: If you are using Google Chrome 45 and its above version
  • Hikvision DS-2CD2083G0-I | User Manual - Page 38
    microphone. / Start/stop digital zoom function. Note: The icons vary according to the different camera models. Recording and Capturing Pictures Manually Note: To realize PTZ control, the camera connected to the network must support the PTZ function or have a pan/tilt unit installed to the
  • Hikvision DS-2CD2083G0-I | User Manual - Page 39
    Network Camera User Manual PTZ Control Panel Click the zoom/focus/iris buttons to realize lens control. Notes:  There are eight direction arrows in the control panel. Click the arrows to realize adjustment in the relative positions.  For the cameras which support lens movements only, the
  • Hikvision DS-2CD2083G0-I | User Manual - Page 40
    Network Camera User Manual Setting/Calling a Preset  Setting a Preset: 1. In the PTZ control panel, the preset.  Calling a Preset: This feature enables the camera to point to a specified preset scene manually or when an event takes place. For the defined preset, you can call it at any time to
  • Hikvision DS-2CD2083G0-I | User Manual - Page 41
    Network Camera User Manual Calling a Preset Setting/Calling a Patrol Note: No less than 2 presets have to be configured before you set a patrol. Steps: 1. Click to enter the patrol configuration
  • Hikvision DS-2CD2083G0-I | User Manual - Page 42
    Network Camera User Manual Chapter 6 Network Camera Configuration Configuring Local Parameters Purpose: The local configuration refers to the parameters of the live view, record files and captured pictures. The
  • Hikvision DS-2CD2083G0-I | User Manual - Page 43
    the recorded video files. Valid for the record files you recorded with the web browser.  Record File Size: Select the packed size of the manually recorded and downloaded video files to 256M, 512M or 1G. After the selection, the maximum record file size is the value you selected.  Save record files
  • Hikvision DS-2CD2083G0-I | User Manual - Page 44
    in live view to: Set the saving path of the manually captured pictures in live view mode.  Save snapshots when System Settings Purpose: Follow the instructions below to configure the system settings the Update button that appears on the right of Firmware Version text field to see if there is a new
  • Hikvision DS-2CD2083G0-I | User Manual - Page 45
    User Manual the firmware for the camera. Online Upgrade Note: When the camera is upgrading, don't power off the camera. During upgrading, the camera may not be accessible. You need to wait 1 or 2 minutes before the upgrade finishes. Configuring Time Settings Purpose: You can follow the instructions
  • Hikvision DS-2CD2083G0-I | User Manual - Page 46
    customized network, NTP software can be used to establish a NTP server for time synchronization.  Configure the manual time synchronization. (1) Check the Manual Time Sync. item to enable the manual time synchronization function. (2) Click the icon to select the date, time from the pop-up calendar
  • Hikvision DS-2CD2083G0-I | User Manual - Page 47
    Network Camera User Manual Time Sync Manually  Click Save to save the settings. Configuring RS232 Settings The RS232 port can be used in two ways:  Parameters Configuration: Connect a computer to the camera
  • Hikvision DS-2CD2083G0-I | User Manual - Page 48
    Network Camera User Manual RS232 Settings Note: If you want to connect the camera by the RS232 port, the parameters of the RS232 should be exactly the same with
  • Hikvision DS-2CD2083G0-I | User Manual - Page 49
    Network Camera User Manual RS-485 Settings 2. Set the RS485 parameters and click Save to save the settings. By default, the Baud Rate is set as 9600 bps, the
  • Hikvision DS-2CD2083G0-I | User Manual - Page 50
    Network Camera User Manual DST Settings 2. Select the start time and the end time. 3. Select the DST Bias. 4. Click Save to activate the settings. Configuring External Devices Purpose: For the device supported external devices, including the wiper on the housing or the LED light, you can control
  • Hikvision DS-2CD2083G0-I | User Manual - Page 51
    Network Camera User Manual the Start Time and End Time. Set Schedule  Auto: The LED will be turned on according to the environment illumination. 5. Click Save to save the
  • Hikvision DS-2CD2083G0-I | User Manual - Page 52
    Network Camera User Manual the others are hidden. • The function may not be supported by some camera models. Open Source > Maintenance > Upgrade & Maintenance.  Reboot: Restart the device.  Restore: Reset all the parameters, except the IP parameters and user information, to the default settings.
  • Hikvision DS-2CD2083G0-I | User Manual - Page 53
    Network Camera User Manual encryption password is required when you import the file to other cameras. Diagnose Information: click to download log and : 1. Select firmware or firmware directory to locate the upgrade file. Firmware: Locate the exact path of the upgrade file. Firmware Directory: Only
  • Hikvision DS-2CD2083G0-I | User Manual - Page 54
    Network Camera User Manual Log Searching Interface 2. Set the log search conditions to specify , click Export to save the log files. System Service Purpose: System service settings refer to the hardware service the camera supports. Supported functions vary according to the different cameras. For the
  • Hikvision DS-2CD2083G0-I | User Manual - Page 55
    Network Camera User Manual ABF (Auto Back Focus), Auto Defog, or Status LED, you can select to enable or disable the corresponding service according to the , including Authentication, IP Address Filter, and Security Service from security interface. Authentication Purpose: You can specifically
  • Hikvision DS-2CD2083G0-I | User Manual - Page 56
    Network Camera User Manual Digest is the recommended authentication method for better data security. You must be aware of the risk if you adopt basic as the authentication method. 3.
  • Hikvision DS-2CD2083G0-I | User Manual - Page 57
    Network Camera User Manual Add an IP (3) Click the OK to finish adding.  Modify an IP Address Steps: the IP address(es) and click Delete. 5. Click Save to save the settings. Security Service To enable the remote login, and improve the data communication security, the camera provides the security
  • Hikvision DS-2CD2083G0-I | User Manual - Page 58
    Network Camera User Manual Security Service 2. Check the checkbox of Enable Illegal Login Lock. Illegal Login Lock: it is used to limit the user login attempts. Login attempt from the IP
  • Hikvision DS-2CD2083G0-I | User Manual - Page 59
    Network Camera User Manual accounts. The admin user cannot be deleted and you can only change increase the security of your product. And we recommend you reset your password regularly, especially in the high security system, resetting the password monthly or weekly can better protect your product.
  • Hikvision DS-2CD2083G0-I | User Manual - Page 60
    Network Camera User Manual 4. Click OK to finish the user modification.  Deleting a User Steps: 1. Old password is required for this action. Security Question Purpose: Security question is used to reset the admin password when admin user forgets the password. Set Security Question: You can set the
  • Hikvision DS-2CD2083G0-I | User Manual - Page 61
    Network Camera User Manual 2. Click Forget Password. 3. Answer security question. 4. Create new password. Note: User IP address is locked for 30 minutes after 7 failed attempts of answering security questions.
  • Hikvision DS-2CD2083G0-I | User Manual - Page 62
    IP, DDNS, PPPoE, Port, and NAT, etc., by following the instructions in this section. Configuring TCP/IP Settings Purpose: TCP/IP settings must be properly configured before you operate the camera over network. The camera supports both the IPv4 and IPv6. Both versions can be configured simultaneously
  • Hikvision DS-2CD2083G0-I | User Manual - Page 63
    Network Camera User Manual TCP/IP Settings 2. Configure the basic network settings, including the NIC Type, IPv4 or IPv6 Address, IPv4 or IPv6 Subnet Mask, IPv4 or IPv6 Default
  • Hikvision DS-2CD2083G0-I | User Manual - Page 64
    Network Camera User Manual multicast group address. Before utilizing this function, you have to enable the Multicast function of your router.  A reboot is required for the settings to take
  • Hikvision DS-2CD2083G0-I | User Manual - Page 65
    Network Camera User Manual Figure 7-2 DynDNS Settings  NO-IP: Steps: (1)Choose the DDNS Type as NO-IP. Figure 7-3 NO-IP DNS Settings (2) Enter the Server Address as www.noip.
  • Hikvision DS-2CD2083G0-I | User Manual - Page 66
    Network Camera User Manual Configuring PPPoE Settings Steps: 1. Enter the PPPoE Settings interface: Configuration > Network > Basic Settings > PPPoE PPPoE Settings 2. Check the Enable PPPoE checkbox to enable this feature. 3.
  • Hikvision DS-2CD2083G0-I | User Manual - Page 67
    Network Camera User Manual You can set the port No. of the camera, e.g., HTTP port, RTSP port and HTTPS port. Steps: 1. Enter the Port Settings interface, Configuration > Network > Basic
  • Hikvision DS-2CD2083G0-I | User Manual - Page 68
    Network Camera User Manual Note: WebSocket and WebSockets protocol are used for plug-in free live view. For detailed information, see 7.2.11. 3. Click Save to save the settings. Note: A
  • Hikvision DS-2CD2083G0-I | User Manual - Page 69
    and complete port mapping settings on router manually. 5. Click Save to save the settings. Configure Advanced Settings Purpose: You can configure the parameters, including SNMP, FTP, Email, HTTPS, QoS, 802.1x, etc., by following the instructions in this section. Configuring SNMP Settings Purpose
  • Hikvision DS-2CD2083G0-I | User Manual - Page 70
    Network Camera User Manual strongly recommend the use of strong passwords for all functions and network devices. The password should be something of your own choosing (using a minimum of 8
  • Hikvision DS-2CD2083G0-I | User Manual - Page 71
    Network Camera User Manual SNMP Settings 2. Check the checkbox of Enable SNMPv1, Enable SNMP v2c, Enable SNMPv3 to enable the feature correspondingly. 3. Configure the SNMP settings. Note: The settings of the SNMP software should be the same as the settings you 70
  • Hikvision DS-2CD2083G0-I | User Manual - Page 72
    Network Camera User Manual configure here. 4. Click Save to save and finish the settings. Notes: • A reboot is required for the settings to take effect. • To lower the risk of
  • Hikvision DS-2CD2083G0-I | User Manual - Page 73
    FTP server login. Network Camera User Manual  For your privacy and to better protect your system against security risks, we strongly recommend the use of strong passwords for all functions and network
  • Hikvision DS-2CD2083G0-I | User Manual - Page 74
    Network Camera User Manual anonymous access to the FTP server. Note: The anonymous access function must be supported by the FTP server. 6. Click Save to save the settings. 7.2.3 Configuring Email Settings Purpose: The system can be configured to send an Email notification to
  • Hikvision DS-2CD2083G0-I | User Manual - Page 75
    Network Camera User Manual The SMTP port should be set as 465 for this you want to use STARTTLS, make sure that the protocol is supported by your e-mail server. If you check the Enable STARTTLS checkbox when the protocol is not supported by your e-mail sever, your e-mail will not be encrypted
  • Hikvision DS-2CD2083G0-I | User Manual - Page 76
    Network Camera User Manual 4. Click Save to save the settings. Email Settings Platform Access Purpose: Platform access provides you an option to manage the devices via platform. Steps: 1. Enter
  • Hikvision DS-2CD2083G0-I | User Manual - Page 77
    Network Camera User Manual If you select Platform Access Mode as Hik-Connect, 1) Click and read "Terms of Service" and "Privacy Policy" in pop-up wireless dial function may not be supported by some camera models. • Camera that supports wireless dial does not support PPPoE. Steps: 1. Click Wireless
  • Hikvision DS-2CD2083G0-I | User Manual - Page 78
    . Auto, 3G and 4G are selectable. If Auto is selected, the network selection priority comes as: 4G > 3G > Wired Network. 4) Input the offline time if Manual is selected as the dial mode. 5) Input the UIM Number (Mobile Phone Number). 6) Click the Edit button to set the arming schedule if Auto is
  • Hikvision DS-2CD2083G0-I | User Manual - Page 79
    Network Camera User Manual 4) (Optional) You can click Send Test SMS to send a message to the mobile phone for test. 5) Click Save to save the settings. HTTPS Settings Purpose:
  • Hikvision DS-2CD2083G0-I | User Manual - Page 80
    Network Camera User Manual Create Self-signed Certificate  Create the self-signed certificate (1) certificate request. Fill in the required information in the popup window. (3) Click Download to download the certificate request and submit it to the trusted certificate authority for signature. (4)
  • Hikvision DS-2CD2083G0-I | User Manual - Page 81
    Network Camera User Manual Import the Certificate (1) b) Select Create the certificate request first and continue the installation. Click Browse and Install to import the certificate to the device. Import
  • Hikvision DS-2CD2083G0-I | User Manual - Page 82
    Network Camera User Manual QoS (Quality of Service) can help solve the network delay and network congestion by settings to take effect. Configuring 802.1X Settings Purpose: The IEEE 802.1X standard is supported by the network cameras, and when the feature is enabled, the camera data is secured
  • Hikvision DS-2CD2083G0-I | User Manual - Page 83
    Network Camera User Manual  For your privacy and to better protect your system against security risks, we strongly recommend the use of strong passwords for all functions and network
  • Hikvision DS-2CD2083G0-I | User Manual - Page 84
    Network Camera User Manual Integration Protocol Purpose: If you need to access to the camera through the third party platform, you can enable CGI function. And if you need
  • Hikvision DS-2CD2083G0-I | User Manual - Page 85
    Network Camera User Manual Network Service You can control the ON/OFF status of certain protocol that the camera supports. Note: • Keep unused function OFF for security concern. • The function is supported by certain camera model. WebSocket or WebSockets protocol are used for plug-in-free live view.
  • Hikvision DS-2CD2083G0-I | User Manual - Page 86
    Network Camera User Manual Chapter 8Video/Audio Settings Purpose: Follow the instructions below to configure the video setting, audio settings, ROI, Display info. on Stream, etc. Configuring Video Settings For certain camera models, you can configure parameters
  • Hikvision DS-2CD2083G0-I | User Manual - Page 87
    Network Camera User Manual Video Settings 2. Select the Stream Type. Supported stream types are listed in the drop-down list. Notes: • For some models, the Third Stream is not enabled by default. Go to System > Maintenance > System Service> Software to enable the function is required. • The main
  • Hikvision DS-2CD2083G0-I | User Manual - Page 88
    Network Camera User Manual When bitrate type is selected as Variable, 6 levels of video quality is 8192 Kbps or 12288 Kbps. Video Encoding: The camera supports multiple video encodings types, such as H.264, H.265, MJPEG, and MPEG4. Supported encoding type for different stream types may differ. H.265
  • Hikvision DS-2CD2083G0-I | User Manual - Page 89
    out. • With H.264+/H.265+ enabled, some functions are not supported. For those functions, corresponding interfaces will be hidden. • H.264+/H. the Max. Average Bitrate box. You can also set the maximum average bitrate manually from 32 Kbps to the value of the set maximum bitrate. Profile: When
  • Hikvision DS-2CD2083G0-I | User Manual - Page 90
    Network Camera User Manual bandwidth is insufficient. Smoothing: It refers to the smoothness can live view them, but cannot record or playback them. Notes: • Custom video function requires the support of the camera. • After a camera restore action (not restore to default setting), quantity of custom
  • Hikvision DS-2CD2083G0-I | User Manual - Page 91
    Network Camera User Manual Steps: Custom Video Settings 1. Click to add a stream. 2. Change the stream name if needed. Note: Up to 32 letters and symbols (except or ") are allowed
  • Hikvision DS-2CD2083G0-I | User Manual - Page 92
    Network Camera User Manual Audio Settings 2. Configure the following settings. Note: Audio settings vary Sampling Rate can be set. Audio Input: MicIn and LineIn are selectable for the connected microphone and pickup respectively. Input Volume: 0-100 adjustable. Environmental Noise Filter: Set it as
  • Hikvision DS-2CD2083G0-I | User Manual - Page 93
    Network Camera User Manual Region of Interest Settings Steps: 1. Enter the ROI settings interface: Configuration > Video/Audio > ROI. 2. Select the Stream Type for ROI encoding. 3. Check the checkbox of
  • Hikvision DS-2CD2083G0-I | User Manual - Page 94
    Network Camera User Manual (3) Click Drawing. Click and drag the mouse on the view checkbox to enable Face Tracking. Note: To enable face tracking function, the face detection function should be supported and enabled. (2) Select the ROI level. 6. Click Save to save the settings. Note: ROI level
  • Hikvision DS-2CD2083G0-I | User Manual - Page 95
    Network Camera User Manual Configuring Target Cropping Purpose: You can specify a target area on the live video, and then the specified video area can be displayed via the third
  • Hikvision DS-2CD2083G0-I | User Manual - Page 96
    Network Camera User Manual Chapter 9 Image Settings Purpose: Follow the instructions in this chapter to configure the image parameters, including display settings, OSD settings, privacy mask, and picture overlay. Configuring Display Settings Purpose: Configure the image
  • Hikvision DS-2CD2083G0-I | User Manual - Page 97
    the brighter would the image be, and the noise would also be amplified to a larger extent. Exposure Settings  Focus For camera support motor-driven lens, you can set the focus mode as Auto, Manual or Semi-auto. Auto: Camera focus is adjusted automatically according to the actual monitoring scenario
  • Hikvision DS-2CD2083G0-I | User Manual - Page 98
    by alarm input. You can set the triggered mode to day or night. Smart Supplement Light: Set the supplement light as ON, and Auto and Manual are selectable for light mode. Select Auto, and the supplement light changes according to the actual luminance. E.g., if the current scene is bright enough
  • Hikvision DS-2CD2083G0-I | User Manual - Page 99
    Network Camera User Manual if the object is near the camera, the device adjusts the supplement light to lower power, and the light is in higher power if the
  • Hikvision DS-2CD2083G0-I | User Manual - Page 100
    Network Camera User Manual and the image is misty. It enhances the subtle details so that appear distorted to some extent. Turn on this function to correct the distortion.  Others Some camera models support CVBS, SDI, or HDMI output. Set the local output ON or OFF according to the actual device.
  • Hikvision DS-2CD2083G0-I | User Manual - Page 101
    illumination. Network Camera User Manual Day/Night Scheduled-Switch Configuration Interface Steps: 1. Click the calendar icon to select the start time and the end time of the switch. Notes: • The
  • Hikvision DS-2CD2083G0-I | User Manual - Page 102
    Network Camera User Manual OSD Settings Steps: 1. Enter the OSD Settings interface: Configuration > Image > OSD Settings. 2. Check the corresponding checkbox to select the display of camera name, date or
  • Hikvision DS-2CD2083G0-I | User Manual - Page 103
    Network Camera User Manual 8. Click Save to save the settings. Configuring Privacy Mask Purpose: Privacy mask enables you to cover certain areas on the live video to prevent certain
  • Hikvision DS-2CD2083G0-I | User Manual - Page 104
    Network Camera User Manual you set without saving them. 6. Click Save to save the settings. Configuring Picture Overlay Purpose: Picture overlay enables you to overlay a picture on the image.
  • Hikvision DS-2CD2083G0-I | User Manual - Page 105
    128*128. Network Camera User Manual 104
  • Hikvision DS-2CD2083G0-I | User Manual - Page 106
    Network Camera User Manual Chapter 10 Event Settings This section explains how to configure the network camera to respond to alarm events, including basic event and smart event. Basic Events You can configure the basic events by following the instructions in this section, including motion detection,
  • Hikvision DS-2CD2083G0-I | User Manual - Page 107
    Network Camera User Manual 3. Check the checkbox of Enable Dynamic Analysis for Motion if you want to mark the detected objects with green rectangles. Note: Select Disable for rules
  • Hikvision DS-2CD2083G0-I | User Manual - Page 108
    Network Camera User Manual Task 2: Set the Arming Schedule for Motion Detection Arming Schedule Steps: 1. Click Arming Schedule to edit the arming schedule. 2. Click on the time bar and
  • Hikvision DS-2CD2083G0-I | User Manual - Page 109
    Network Camera User Manual save the settings. 4. Move the mouse to the end of each day, to the different camera models.  Audible Warning Trigger the audible warning locally. And it only supported by the device that have the audio output.  Notify Surveillance Center Send an exception or alarm
  • Hikvision DS-2CD2083G0-I | User Manual - Page 110
    Network Camera User Manual complete Email setup in advance.  Upload to FTP/Memory Card/NAS Capture the image when an alarm is triggered and upload the picture to a FTP
  • Hikvision DS-2CD2083G0-I | User Manual - Page 111
    Network Camera User Manual Expert Mode of Motion Detection  Day/Night Switch OFF Steps: 1. Draw the detection area as in the normal configuration mode. Up to 8 areas are supported. 2. Select OFF for Switch Day and Night Settings. 3. Select the area by clicking the area No. 4. Slide the cursor to
  • Hikvision DS-2CD2083G0-I | User Manual - Page 112
    Network Camera User Manual 6. Set the arming schedule and linkage method as in the normal configuration mode. 7. Click Save to save the settings.  Day/Night Scheduled-Switch Steps: 1. Draw the detection area as in the normal configuration mode. Up to 8 areas are supported. 2. Select Scheduled-
  • Hikvision DS-2CD2083G0-I | User Manual - Page 113
    Network Camera User Manual 2. Check Enable Video Tampering checkbox to enable the video tampering detection. 3. Click Edit to edit the arming schedule for video tampering. The arming schedule configuration
  • Hikvision DS-2CD2083G0-I | User Manual - Page 114
    Network Camera User Manual Alarm Input Settings 3. Click Arming Schedule to set the arming schedule for the alarm input. Refer to Task 2: Set the Arming Schedule for Motion Detection
  • Hikvision DS-2CD2083G0-I | User Manual - Page 115
    Network Camera User Manual 10.1.4 Configuring Alarm Output Alarm Output Settings Steps: 1. Enter the ). 3. The Delay time can be set to 5sec, 10sec, 30sec, 1min, 2min, 5min, 10min or Manual. The delay time refers to the time duration that the alarm output remains in effect after alarm occurs. 4.
  • Hikvision DS-2CD2083G0-I | User Manual - Page 116
    Network Camera User Manual 6. Click Save to save the settings. 10.1.5 Handling Exception The to save the settings. Exception Settings 10.1.6 Configuring Other Alarm Note: Some certain cameras support Wireless Alarm, PIR (passive infrared sensor) Alarm or Emergency Alarm.  Wireless Alarm Purpose
  • Hikvision DS-2CD2083G0-I | User Manual - Page 117
    Network Camera User Manual Configuration > Advanced Configuration> Basic Event> Wireless Alarm Setting Wireless Alarm 2. Select the wireless alarm number. Up to 8 channels of external wireless alarm input are supported. 3. Check the checkbox of Enable Wireless Alarm to activate the wireless alarm.
  • Hikvision DS-2CD2083G0-I | User Manual - Page 118
    Network Camera User Manual A PIR (Passive Infrared) alarm is triggered when an intruder moves within the detector's field of view. The heat energy dissipated by a person, or any other
  • Hikvision DS-2CD2083G0-I | User Manual - Page 119
    Network Camera User Manual Figure 10-13 Arming PIR Alarm  Emergency Alarm Purpose: You can press the save the settings. Smart Events You can configure the smart events by following the instructions in this section, including audio exception detection, defocus detection, scene change detection, 118
  • Hikvision DS-2CD2083G0-I | User Manual - Page 120
    Network Camera User Manual intrusion detection, and line crossing detection, etc. These events can trigger the linkage methods, such as Notify Surveillance Center, Send Email, Trigger Alarm Output, etc.
  • Hikvision DS-2CD2083G0-I | User Manual - Page 121
    Network Camera User Manual the sound steep rise in the surveillance scene. You can set the detection sensitivity and threshold for sound steep rise. 4. Check the checkbox of Sudden
  • Hikvision DS-2CD2083G0-I | User Manual - Page 122
    Network Camera User Manual Configuring Defocus Detection 2. Check the checkbox of Enable to enable the function. 3. Click-and-drag the slider to set the detection sensitivity. The sensitivity value
  • Hikvision DS-2CD2083G0-I | User Manual - Page 123
    Network Camera User Manual Scene Change Detection 2. Check the checkbox of Enable to enable the function. 3. Click-and-drag the slider to set the detection sensitivity. The sensitivity value
  • Hikvision DS-2CD2083G0-I | User Manual - Page 124
    Network Camera User Manual 1. Enter the Face Detection settings interface, Configuration > Event > Smart Event > Face Detection. 2. Check the Enable Face Detection checkbox to enable the function. 3. Check the checkbox
  • Hikvision DS-2CD2083G0-I | User Manual - Page 125
    Network Camera User Manual 7. Click Save to save the settings. Configuring Intrusion Detection Purpose: Intrusion detection function detects people, vehicle or other objects which enter and loiter in a pre-
  • Hikvision DS-2CD2083G0-I | User Manual - Page 126
    Network Camera User Manual 2. Check the checkbox of Enable to enable the function. 3. Select a region number from the drop-down list of only when 40 percent body part enters the region. Note: The Sensitivity of the detection is supported by certain models. Refer to actual display for details. 125
  • Hikvision DS-2CD2083G0-I | User Manual - Page 127
    Network Camera User Manual 10. Repeat the above steps to configure other regions. Up to 4 regions can be set. You can click the Clear button to clear all pre-
  • Hikvision DS-2CD2083G0-I | User Manual - Page 128
    Network Camera User Manual Line Crossing Detection 2. Check the checkbox of Enable to enable the function. 3. Select the line from the drop-down list. 4. Click Area Settings tab and
  • Hikvision DS-2CD2083G0-I | User Manual - Page 129
    Network Camera User Manual Max. Size: The maximum size of a valid target. Targets with when 40 percent or more body part goes across the line. Note: The Sensitivity of the detection is supported by certain models. Refer to actual display for details. 10. Repeat the above steps to configure other
  • Hikvision DS-2CD2083G0-I | User Manual - Page 130
    Network Camera User Manual Configuring Region Entrance Detection Purpose: Region entrance detection function detects people, vehicle or other objects which enter a pre-defined virtual region from the outside place,
  • Hikvision DS-2CD2083G0-I | User Manual - Page 131
    Network Camera User Manual 4. Click Area Settings and click Draw Area button to entrance action only when 40 percent body part enters the region. Note: The Sensitivity of the detection is supported by certain models. Refer to actual display for details. 9. Repeat the above steps to configure other
  • Hikvision DS-2CD2083G0-I | User Manual - Page 132
    Network Camera User Manual from a pre-defined virtual region, and some certain actions can be taken when the alarm is triggered. Steps: 1. Enter the Region Exiting Detection settings interface,
  • Hikvision DS-2CD2083G0-I | User Manual - Page 133
    Network Camera User Manual not trigger detection. Min. Size: The minimum size of a valid action only when 40 percent body part exits the region. Note: The Sensitivity of the detection is supported by certain models. Refer to actual display for details. 9. Repeat the above steps to configure other
  • Hikvision DS-2CD2083G0-I | User Manual - Page 134
    Network Camera User Manual Unattended Baggage Detection 2. Check Enable checkbox to enable the function. 3. Select the Region from the drop-down list for detection settings. 4. Click Area Settings and
  • Hikvision DS-2CD2083G0-I | User Manual - Page 135
    Network Camera User Manual Threshold: Range [5-100s], the threshold for the time of when 40 percent body part of the target enters the region. Note: The Sensitivity of the detection is supported by certain models. Refer to actual display for details. 10. Repeat the above steps to configure other
  • Hikvision DS-2CD2083G0-I | User Manual - Page 136
    Network Camera User Manual Object Removal Detection 2. Check Enable checkbox to enable the function. 3. Select the Region from the drop-down list for detection settings. 4. Click Area Settings and
  • Hikvision DS-2CD2083G0-I | User Manual - Page 137
    Network Camera User Manual disappears from the region for 10s. 9. Drag the slider when 40 percent body part of the target leaves the region. Note: The Sensitivity of the detection is supported by certain models. Refer to actual display for details. 10. Repeat the above steps to configure other
  • Hikvision DS-2CD2083G0-I | User Manual - Page 138
    Network Camera User Manual Behavior Analysis  Overlay & Capture Display information includes the display on picture and display on stream. Display VCA info. on Stream: The green frames will be
  • Hikvision DS-2CD2083G0-I | User Manual - Page 139
    Input Basic Data or Draw on Live View Video. Input Basic Data: Input the mounting height, viewing angle, and horizon ratio of the camera manually. Draw on Live View Video: Click Draw Verification Line (Horizontal) / (Vertical) to draw a horizontal/vertical line in the live view, and input the actual
  • Hikvision DS-2CD2083G0-I | User Manual - Page 140
    Network Camera User Manual 4. You can click to delete the drawn lines. 5. Click Save to save the settings.  Shield Region The shield region allows you to set the specific region in which the behavior analysis will not function. Up to 4 shield regions are supported. Steps: 1. Click Shield Region tab
  • Hikvision DS-2CD2083G0-I | User Manual - Page 141
    Network Camera User Manual Configure the Rule Filter type: Pixels and Actual Size are selectable. If Pixels is selected, draw the area of maximum size and minimum size on
  • Hikvision DS-2CD2083G0-I | User Manual - Page 142
    Network Camera User Manual to left click on the live video to set the end rules and 2 combined rules are configurable. And the line crossing, intrusion, region exiting and region entrance are supported for the combined rules. 6. Click Save to save the settings. 7. Click Arming Schedule tab to set the
  • Hikvision DS-2CD2083G0-I | User Manual - Page 143
    Network Camera User Manual Advanced Configuration Detection Sensitivity [0~4]: Refers to the sensitivity of the camera detects a target. The higher the value, the easier a target be recognized, and the higher
  • Hikvision DS-2CD2083G0-I | User Manual - Page 144
    Network Camera User Manual 1. Check the checkbox of Global Size Filter to enable the function. 2. Select the Filter Type as Actual Size or Pixel. Actual Size: Input the length
  • Hikvision DS-2CD2083G0-I | User Manual - Page 145
    Network Camera User Manual if in a live view or playback. Display Target info. on Alarm to set the specific region in which the face capture will not function. Up to 4 shield regions are supported. Steps: 1. Click the hexagons sign to draw shield area by left click end-points in the live view
  • Hikvision DS-2CD2083G0-I | User Manual - Page 146
    Network Camera User Manual 1. Check the checkbox of Rule to enable rules of face capture. live view window, and right click to finish the area drawing. Notes:  Polygon area (4~10 sides) sides is supported.  If the live view is stopped, there is no way to draw the configured area. 4. Click Save to
  • Hikvision DS-2CD2083G0-I | User Manual - Page 147
    Network Camera User Manual faster the target will be recognized. Setting the value quite low minute. Note: If the face exposure is enabled, please make sure the WDR function is disabled, and the manual iris is selected. Enable Face ROI: If the camera captures a face, the face area will be treated as
  • Hikvision DS-2CD2083G0-I | User Manual - Page 148
    Network Camera User Manual People Counting Purpose: People function is used to calculate the number of object entered or exited a certain configured area and it is widely applied to
  • Hikvision DS-2CD2083G0-I | User Manual - Page 149
    Network Camera User Manual 3. Set the detection line. An orange line, named as detection line can be set on the live video, and the object entering or exiting through
  • Hikvision DS-2CD2083G0-I | User Manual - Page 150
    the real-time counting data, check the Real-Time Upload Data checkbox. 4) If you want manually set the counting cycle, select the desired time period from the Data Statistics Cycle dropdown list. 5) To reset the counter, click the button on the left of the live view image. 6. Click Arming Schedule
  • Hikvision DS-2CD2083G0-I | User Manual - Page 151
    Network Camera User Manual Counting Counting function helps to calculate the number of people entered or exited a certain configured area and is widely applied to the entrances or exits. Compared with the people counting function supported by iDS camera, counting function needs no camera calibration
  • Hikvision DS-2CD2083G0-I | User Manual - Page 152
    Network Camera User Manual people entered and exited is displayed on the live video. 4. Set the detection line. An orange line, named as detection line can be set on
  • Hikvision DS-2CD2083G0-I | User Manual - Page 153
    Network Camera User Manual Heat Map Configuration 2. Check Enable Heat Map checkbox to enable the function. 3. Go to Area Settings to draw detection area. Draw area by left click
  • Hikvision DS-2CD2083G0-I | User Manual - Page 154
    Network Camera User Manual camera treats the cabinet (on which the good removed) as a new scene. The default value of 50 is recommended. Scene Change Level [0~100]: It refers
  • Hikvision DS-2CD2083G0-I | User Manual - Page 155
    Network Camera User Manual Note: Road traffic function varies according to different camera models.  Detection Configuration Steps: 1. Select the detection type from the list. Vehicle Detection and Mixed-traffic
  • Hikvision DS-2CD2083G0-I | User Manual - Page 156
    Network Camera User Manual • Upload to FTP/Memory Card/NAS: Capture the image when an alarm queue management, go to Application. Note: Queue management is only supported by certain camera models. Rule Settings The camera supports Regional People Queuing-Up and Waiting Time Detection. Check checkbox
  • Hikvision DS-2CD2083G0-I | User Manual - Page 157
    Network Camera User Manual is that his/her head and shoulder enter the region. Steps: i. Click Add Region. ii. (Optional) Select a color for a region from the color drop-down list. iii. Draw a region by right click to determine the region boundary. Up to 10 edges are supported for a region. Move the
  • Hikvision DS-2CD2083G0-I | User Manual - Page 158
    Network Camera User Manual Alarm Interval: In the set alarm interval, alarms of an alarm is triggered. c) Repeat above steps to set up other regions if needed. Up to 3 regions are supported. 2. Arming Schedule. Set the arming schedule for the function. In the armed periods, the function is active.
  • Hikvision DS-2CD2083G0-I | User Manual - Page 159
    device configured. Configuring Record Schedule Purpose: There are two kinds of recording for the cameras: manual recording and scheduled recording. In this section, you can follow the instructions to configure the scheduled recording. By default, the record files of scheduled recording are stored
  • Hikvision DS-2CD2083G0-I | User Manual - Page 160
    Network Camera User Manual Record Parameters  Pre-record: The time you set to start recording before the scheduled time or the event. For example, if an alarm triggers recording
  • Hikvision DS-2CD2083G0-I | User Manual - Page 161
    Network Camera User Manual please refer to the Task 1: Set the Motion Detection Area in the Section 10.1.1.  Record Triggered by Alarm If you select Alarm, the video will
  • Hikvision DS-2CD2083G0-I | User Manual - Page 162
    Network Camera User Manual Configure Capture Schedule Purpose: You can configure the scheduled snapshot and event-triggered snapshot. The captured picture can be stored in the local storage or
  • Hikvision DS-2CD2083G0-I | User Manual - Page 163
    Network Camera User Manual 4. Click Save to save the settings. 5. Go to Capture Parameters tab to configure the capture parameters. (1) Check the Enable Timing Snapshot checkbox to enable continuous
  • Hikvision DS-2CD2083G0-I | User Manual - Page 164
    Network Camera User Manual Configuring Net HDD Before you start: The network disk should and password to guarantee the security if SMB/CIFS is selected. Note: Please refer to the NAS User Manual for creating the file path.  For your privacy and to better protect your system against security risks,
  • Hikvision DS-2CD2083G0-I | User Manual - Page 165
    Network Camera User Manual responsibility of the installer and/or end-user. (4) Click Save to add the network disk. 2. Initialize the added network disk. (1) Enter the HDD Settings interface,
  • Hikvision DS-2CD2083G0-I | User Manual - Page 166
    Network Camera User Manual Quota Settings Note: Up to 8 NAS disks can be connected to and receive notification when your memory card is detected abnormal. Note: Memory card detection function is only supported by certain types of memory cards and camera models. If this tab page doesn't show on your
  • Hikvision DS-2CD2083G0-I | User Manual - Page 167
    Network Camera User Manual Memory Card Detection 2. View the memory card status on Status Detection tab. Remaining Lifespan: It shows the percentage of the remaining lifespan. The lifespan of a
  • Hikvision DS-2CD2083G0-I | User Manual - Page 168
    (2) If you use the memory card (with a lock) on a different camera, you can go to HDD Management interface to unlock the memory card manually. Select the memory card, and click the Unlock button shown next to the Format button. Then input the correct password to unlock it. Notes: • The
  • Hikvision DS-2CD2083G0-I | User Manual - Page 169
    Network Camera User Manual 2. Check the Checkbox of Enable to enable the lite storage function. 3. Input the storage time in the text field. You can view the available space of the SD card on the page. 4. Click Save to save the settings. 168
  • Hikvision DS-2CD2083G0-I | User Manual - Page 170
    Network Camera User Manual Chapter 12 Playback Purpose: This section explains how to view the remotely recorded video files stored in the network disks or SD cards. Steps: 1. Click
  • Hikvision DS-2CD2083G0-I | User Manual - Page 171
    Network Camera User Manual The toolbar on the bottom of Playback interface can be used to Operation Capture a picture Start/Stop clipping video files Audio on and adjust volume/Mute Speed down Download Speed up Playback by frame Enable/Disable / digital zoom Note: You can choose the file paths
  • Hikvision DS-2CD2083G0-I | User Manual - Page 172
    Network Camera User Manual Chapter 13 Picture Click Picture to enter the picture searching interface. You can search, view, and download the pictures stored in the local storage or network storage. Notes:  Make sure HDD, NAS or memory card are properly configured before you process the
  • Hikvision DS-2CD2083G0-I | User Manual - Page 173
    Network Camera User Manual Chapter 14 Application Click Application to enter the statistics counting interface. You can search, view, and download the counting data stored in the local storage or network storage. Note: Application function varies according to the different camera models. Face
  • Hikvision DS-2CD2083G0-I | User Manual - Page 174
    Network Camera User Manual counting data from application tab. To get more intuitional results, file. People Counting Heat Map Statistics After you enable the heat map function, you can view and download the heat map data from application tab. To get more intuitional results, you can display the data
  • Hikvision DS-2CD2083G0-I | User Manual - Page 175
    Network Camera User Manual Note: Daily report calculates the data on the date you selected; weekly report degree. Counting Statistics After you enable the counting function, you can view and download the counting data from application tab. To get more intuitional results, you can display the data in
  • Hikvision DS-2CD2083G0-I | User Manual - Page 176
    Network Camera User Manual different charts. Steps: 1. Select the report type. Daily report, button to export the data in an excel file. Queue Management Statistics Purpose: Queue management supports data analysis and report output from multiple dimensions. Commonly Used Data Analysis • To see
  • Hikvision DS-2CD2083G0-I | User Manual - Page 177
    Network Camera User Manual • To compare the time and duration that a queue stays a certain length of different waiting time levels. Regional comparison and multiple waiting time level comparison are supported. Steps: 1. Select Statistic Type. Regional Comparison: Compares queuing-up people number of
  • Hikvision DS-2CD2083G0-I | User Manual - Page 178
    Network Camera User Manual 2. Select Report Type. Daily report, weekly report, and monthly report are supported. 3. Select Statistics Time. 4. length. Regional comparison and multiple queue length level comparison are supported. Steps: 1. Select Statistic Type. Regional Comparison: Compares the
  • Hikvision DS-2CD2083G0-I | User Manual - Page 179
    Network Camera User Manual 3. Select Statistics Time. 4. Click Counting to generate the report. 5. (Optional) Click Export in the upper right corner to export the data in desired format (.txt
  • Hikvision DS-2CD2083G0-I | User Manual - Page 180
    Network Camera User Manual Appendix Appendix 1 SADP Software Introduction  Description of SADP SADP (Search Active Devices Protocol) is a kind of user-friendly and installation-free online device search tool.
  • Hikvision DS-2CD2083G0-I | User Manual - Page 181
    can also click to refresh the online device list manually. The newly searched devices will be added to the list. You can click or on each column heading to order the information; you can click
  • Hikvision DS-2CD2083G0-I | User Manual - Page 182
    Network Camera User Manual Figure A.1.2 Modify Network Parameters 181
  • Hikvision DS-2CD2083G0-I | User Manual - Page 183
    Network Camera User Manual Appendix 2 Port Mapping The following settings are for TP-LINK router (TL-WR641G). The settings vary depending on different models of routers. Steps: 1. Select the
  • Hikvision DS-2CD2083G0-I | User Manual - Page 184
    Network Camera User Manual another camera as 81, 8001, 555, 8201 with IP 192.168.1.24. Refer to the steps as below: Steps: 1. As the settings mentioned above, map
  • Hikvision DS-2CD2083G0-I | User Manual - Page 185
    Network Camera User Manual 184
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
Network Camera User Manual
0
User Manual
UD09650B
Network Camera