Hitachi CP-X2514WN User Manual

Hitachi CP-X2514WN Manual

Get Hitachi CP-X2514WN PDF manuals and user guides View all Hitachi CP-X2514WN manuals
Add to My Manuals
Save this manual to your list of manuals

Hitachi CP-X2514WN manual content summary:

  • Hitachi CP-X2514WN | User Manual - Page 1
    Projector CP-X2514WN/CP-X3014WN/ CP-X4014WN/CP-WX3014WN User's Manual (detailed) Operating Guide Thank you for purchasing this projector. WARNING ►Before using this product, please read all manuals for this product. Be sure to read Safety Guide first. After reading them, store them in a safe place
  • Hitachi CP-X2514WN | User Manual - Page 2
    . . . 18 Usb type b, Lamp time, Filter time, Power on/off 19 My button, My source, Service Turning on the power 19 NETWORK menu 63 Turning off the power 19 Wireless setup, Wireless information, Operating 20 Wired setup, Wired information, Adjusting the volume 20 Projector name, My image
  • Hitachi CP-X2514WN | User Manual - Page 3
    . ü This projector has a variety of I/O ports that supposedly cover for any business scene. The HDMI port can support various image equipment projector can be controlled and monitored via LAN connection. Furthermore, you can use the designated USB wireless adapter (optional) to establish wireless
  • Hitachi CP-X2514WN | User Manual - Page 4
    Projector (1) Lamp cover (&94) The lamp unit is inside. (2) Speaker (&20, 45) (3) Filter cover (&96) (9) The air filter and intake vent are inside. (4) Elevator feet (x2) (&23) (5) Elevator buttons (x2) (&23) (6) Remote unless the manuals direct it. ►Do not subject the projector to unstable
  • Hitachi CP-X2514WN | User Manual - Page 5
    Introduction Part names (continued) Control panel (1) STANDBY/ON button (&19) (2) INPUT button (&21) (3) MENU button (&28) (4) LAMP indicator (&101) (5) TEMP indicator (&101) (6) POWER indicator (&101) (5) (4) (1) (2) (3) (6) Rear panel (&10 ~ 14) (1) LAN port (2) USB TYPE A port (3) HDMI
  • Hitachi CP-X2514WN | User Manual - Page 6
    Introduction Part names (continued) Remote control (1) VIDEO button (&21) (2) COMPUTER button (&21) (3) SEARCH button (&22) (4) STANDBY/ON button (&19) (5) ASPECT button (&22) (6) ENTER ESC RESET (10) (4) (3) (7) (12) (14) (11) (13) (15) (18) (21) (23) (25) Back of the remote control (26) 6
  • Hitachi CP-X2514WN | User Manual - Page 7
    . For the case of installation in a special state such as ceiling mount, the specified mounting accessories (Specifications in the User's Manual (concise)) and service may be required. Before installing the projector, consult your dealer about your installation. Arrangement Refer to tables T-1 and
  • Hitachi CP-X2514WN | User Manual - Page 8
    the accessories specified by the manufacturer. Read and keep the manuals of the accessories used. • For special installation such as ceiling mounting, be sure to consult your dealer beforehand. ►Do not install the projector near thermally conductive or flammable things. Such things when heated
  • Hitachi CP-X2514WN | User Manual - Page 9
    and could be deposited in the projector causing image degradation or other problems. • Do not place the projector in a smoking area, kitchen, passageway or by the window. NOTICE • Position the projector to prevent light from directly hitting the projector's remote sensor. • Do not place the product
  • Hitachi CP-X2514WN | User Manual - Page 10
    and the devices are turned off, perform the connection, according to the following instructions. Refer to the figures in subsequent pages. Before connecting the projector to a network system, be sure to read Network Guide too. WARNING ►Use only the appropriate accessories. Otherwise it could cause
  • Hitachi CP-X2514WN | User Manual - Page 11
    the projector to a computer, consult the computer's manual and check projector. - Some signal may need an adapter to input this projector. - Some computers have multiple screen display modes that may include some signals which are not supported by this projector. - Although the projector
  • Hitachi CP-X2514WN | User Manual - Page 12
    to secure your data (&83). ►Do not use any extension cable or device when connecting the adapter to the projector. Before you insert or pull out the USB wireless adapter from the projector, turn off the power of the projector and pull out the power cord's plug from the outlet. Do not touch the USB
  • Hitachi CP-X2514WN | User Manual - Page 13
    signal from HDCP compatible DVD players or the like. - The HDMI supports the following signals. Video signal : 480i@60, 480p@60, 576i@ Category 2-certified HDMITM cable to input 1080p@50/60 signal to the projector. - W hen the projector is connected with a device having DVI connector, use a DVI
  • Hitachi CP-X2514WN | User Manual - Page 14
    the sound from the projector is output. You can input line level signal to the MIC port from equipment such as wireless microphone. Select HIGH in button on the remote control works on the sounds of the microphone and the projector (&20). • This projector doesn't support plug-in power for the
  • Hitachi CP-X2514WN | User Manual - Page 15
    function activated (&53), the connection of the power supply make the projector turn on. AC IN Power cord WARNING ►Please use extra caution when cord with a wet hand. • Only use the power cord that came with the projector. If it is damaged, consult your dealer to get a new one. Never modify the
  • Hitachi CP-X2514WN | User Manual - Page 16
    wireless adapter from coming off easily. 1. Loosen the screw (marked with triangle) on the bottom left of the 1 USB TYPE A port. 2. Insert the tab of the cover into the hole at the upper right of the USB TYPE A port in the direction of the arrow. 3 3. Align the screw holes on the projector
  • Hitachi CP-X2514WN | User Manual - Page 17
    that could block the remote control's signal to the projector. • The remote control may not work correctly if strong light (such as direct sun light) or light from an extremely close range (such as from an inverter fluorescent lamp) shines on the remote sensor of the projector. Adjust the position
  • Hitachi CP-X2514WN | User Manual - Page 18
    REMOTE FREQ. in the SERVICE item of the OPTION menu (58) of the projector to be controlled should be set to the same mode as the remote check your computer's manuals before connecting this projector is working properly. This function is not available in any of the following cases: - While the lamp
  • Hitachi CP-X2514WN | User Manual - Page 19
    that the POWER indicator is steady orange (101). Then remove the lens cover. 3. Press STANDBY/ON button on the projector or the remote control. The projection lamp will light up and POWER COMPUTER MDYOSCO.CUARMCEER/ A BLANK VIDEO ASPECT SEARCH AUTO PAGEUP FREEZE VOLUME 㧗 MAGNIFY DOWN ON
  • Hitachi CP-X2514WN | User Manual - Page 20
    volume of the microphone is adjustable with the VOLUME +/- buttons on the remote control, in synchronization with the volume of the projector. Temporarily muting the sound MUTE button 1. Press MUTE button on the remote control. A dialog will appear on the screen indicating that you have muted
  • Hitachi CP-X2514WN | User Manual - Page 21
    . ● It may take several seconds to project the images from the USB TYPE B port. 1. Press COMPUTER button on the remote control. Each time you press the button, the projector switches its input port from the current port as below. COMPUTER IN1  COMPUTER IN2  LAN USB TYPE B USB TYPE A COMPUTER
  • Hitachi CP-X2514WN | User Manual - Page 22
    TYPE B port. Selecting an aspect ratio 1. Press ASPECT button on the remote control. Each time you press the button, the projector switches the mode for aspect ratio in turn.  F or a computer signal CP-X2514WN, CP-X3014WN, CP-X4014WN: NORMAL  4:3  16:9  16:10 ASPECT button VIDEO COMPUTER MY
  • Hitachi CP-X2514WN | User Manual - Page 23
    4. After making sure that the elevator feet are locked, put the projector down gently. To finely 5. If necessary, the elevator feet can be manually adjust, twist the foot. twisted to make more precise adjustments. Hold the projector when twisting the feet. CAUTION ►Do not handle the elevator
  • Hitachi CP-X2514WN | User Manual - Page 24
    VIDEO COMPUTER MYSOURCE/ DOC.CAMERA for the AUTO ADJUST item of the SERVICE item in the OPTION menu (57). ASPECT AUTO SEARCH BLANK Adjusting the reset the operation, press RESET button on ENTER ESC RESET the remote control during the operation. To complete this operation, press POSITION button
  • Hitachi CP-X2514WN | User Manual - Page 25
    remote control. A dialog will appear on the screen to aid you in correcting the distortion. 2. Use the ▲/▼ cursor buttons to select AUTO or MANUAL is selected to the MIRROR item in the SETUP menu, if the projector screen is inclined or angled downward, automatic vertical keystone correction may not
  • Hitachi CP-X2514WN | User Manual - Page 26
    button on the remote control. The picture will be magnified, and the MAGNIFY dialog will appear on the screen. When the MAGNIFY ON button is pressed for the first time after the projector is turned on cases: - A sync signal in the range not supported is input. - There is no input signal. 26
  • Hitachi CP-X2514WN | User Manual - Page 27
    a long time, the LCD panel might possibly be burned in. Do not leave the projector in the FREEZE mode for too long. ● Images might appear degraded when this function is operated, but it is not a malfunction. Temporarily blanking the screen 1. Press BLANK button on the remote control. The BLANK
  • Hitachi CP-X2514WN | User Manual - Page 28
    of these menus is operated using the same methods. While the projector is displaying any menu, the MENU button on the projector works as the cursor buttons. The basic operations of these item will appear. (3) Use the buttons as instructed in the OSD to operate the item. (continued on next page) 28
  • Hitachi CP-X2514WN | User Manual - Page 29
    ● When you want to reset the operation, press RESET button on the remote control during the operation. Note that some items (ex. LANGUAGE, VOLUME) previous display, press the ◄ cursor button or ESC button on the remote control. Indication in OSD (On Screen Display) The meanings of the general
  • Hitachi CP-X2514WN | User Manual - Page 30
    EASY MENU EASY MENU From the EASY MENU, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons. Then perform it according to the following table. Item Description ASPECT Using the ◄/► buttons switches the mode for aspect ratio. See the ASPECT item in IMAGE
  • Hitachi CP-X2514WN | User Manual - Page 31
    EASY MENU Item Description ECO MODE Using the ◄/► buttons turns off/on the Eco mode. See the ECO MODE item in SETUP menu (43). MIRROR Using the ◄/► buttons switches the mode for mirror status. See the MIRROR item in SETUP menu (43). RESET Performing this item resets all of the EASY MENU
  • Hitachi CP-X2514WN | User Manual - Page 32
    PICTURE menu PICTURE menu From the PICTURE menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following table. Item BRIGHTNESS CONTRAST Description
  • Hitachi CP-X2514WN | User Manual - Page 33
    . (1) HDMI FORMAT item in the INPUT menu is set to VIDEO. (2) H DMI FORMAT item in the INPUT menu is set to AUTO, and the projector recognizes that it receives video signals. TINT Using the ◄/► buttons adjusts the tint. Reddish ó Greenish • This item can be selected only for a video, s-video
  • Hitachi CP-X2514WN | User Manual - Page 34
    The active iris is always open. • The screen may flicker when the PRESENTATION or THEATER modes are selected. If this occurs select OFF. This projector has 4 memories for adjustment data (for all the items of the PICTURE menu). Selecting a function using the ▲/▼ buttons and pressing the ► or ENTER
  • Hitachi CP-X2514WN | User Manual - Page 35
    LAN, USB TYPE A or USB TYPE B port, or if there is no signal CP-X2514WN, CP-X3014WN, CP-X4014WN: 4:3 (fixed) CP-WX3014WN: 16:10 (fixed) • The NORMAL mode keeps the original aspect ratio of menu is set to AUTO, and the projector recognizes that it receives video signals. (continued on next page) 35
  • Hitachi CP-X2514WN | User Manual - Page 36
    IMAGE menu Item V POSITION H POSITION Description Using the ◄/► buttons adjusts the vertical position. Down ó Up • Over-adjusting the vertical position may cause noise to appear on the screen. If this occurs, please reset the vertical position to the default setting. Pressing the RESET button when
  • Hitachi CP-X2514WN | User Manual - Page 37
    correctly. In such a case, please reset the adjustment by pressing the RESET button on the remote control during this operation. • Images might appear degraded when this function is operated, but it is DISABLE is selected for the AUTO ADJUST item of the SERVICE item in the OPTION menu (57). 37
  • Hitachi CP-X2514WN | User Manual - Page 38
    • When TV or FILM is selected, the screen image will be sharp. FILM adapts to the 2-3 Pull-Down conversion system. But these may cause a certain defect as a SCART RGB port. A SCART adapter or SCART cable is required for a SCART RGB input to the projector. For details, contact your dealer. (continued
  • Hitachi CP-X2514WN | User Manual - Page 39
    INPUT menu Item VIDEO FORMAT Description The video format for S-VIDEO port and VIDEO port can be set. (1) Use the ▲/▼ buttons to select the input port. (2) Using the ◄/► buttons switches the mode for video format. AUTO ó NTSC ó PAL ó SECAM N-PAL ó M-PAL ó NTSC4.43 • This item is performed only
  • Hitachi CP-X2514WN | User Manual - Page 40
    INPUT menu Item COMPUTER IN FRAME LOCK Description The computer input signal type for COMPUTER IN1 and IN2 ports can be set. (1) Use the ▲/▼ buttons to select the COMPUTER IN port to be set. (2) U se the ◄/► buttons to select the computer input signal type. AUTO ó SYNC ON G OFF • Selecting the
  • Hitachi CP-X2514WN | User Manual - Page 41
    COMPUTER IN1 and COMPUTER IN2 input signals can be set on this projector. (1) In the INPUT menu select the RESOLUTION using the ▲/▼ and vertical (VERT) resolutions using CUSTOM ↓ the buttons. This function may not support all resolutions. (5) Move the cursor to OK on screen and press the
  • Hitachi CP-X2514WN | User Manual - Page 42
    to the (forward/backward) setup angle by itself. This function will be executed only once when selected in the menu. When the slant of the projector is changed, execute this function again. • The adjustable range of this function will vary among inputs. For some input, this function may not work
  • Hitachi CP-X2514WN | User Manual - Page 43
    at start-up regardless of the ECO MODE (below) setting. An OSD message "AUTO ECO MODE" will be displayed for tens of seconds when the projector starts with this function activated. ECO MODE Using the ▲/▼ buttons turns off/on the Eco mode. NORMAL ó ECO • When the ECO is selected, acoustic noise
  • Hitachi CP-X2514WN | User Manual - Page 44
    with some functional restriction as below: • When SAVING is selected, the RS-232C communication control except to turn the projector on and the network function are disabled while the projector is in the standby mode. If the COMMUNICATION TYPE in the COMMUNICATION menu is set to NETWORK BRIDGE, all
  • Hitachi CP-X2514WN | User Manual - Page 45
    projected, the audio signal from the input port selected in step (2) is output to both the AUDIO OUT port and built-in speaker of this projector. However, the built-in speaker does not work when SPEAKER is set to OFF. (1) C hoose a picture input port using the ▲/▼ buttons. Choose STANDBY to select
  • Hitachi CP-X2514WN | User Manual - Page 46
    AUDIO menu Item HDMI AUDIO MIC LEVEL MIC VOLUME Description Using the ▲/▼ buttons switches the mode for the HDMITM audio. Check each of the two modes provided and select the suitable one for your HDMITM audio device. 1 ó 2 Using the ▲/▼ buttons switches the input level to match that of the
  • Hitachi CP-X2514WN | User Manual - Page 47
    or INPUT button to save the language setting. Using the buttons adjusts the menu position. To quit the operation, press the MENU button on the remote control or keep no operation for about 10 seconds. Using the ▲/▼ buttons switches the mode for the blank screen. The blank screen is a screen for
  • Hitachi CP-X2514WN | User Manual - Page 48
    for capturing will appear. To stop performing, press the RESET button on the remote control. 2. Using the buttons adjusts the frame position. Please move the frame to the previous dialog, press the RESET button on the remote control. Registration may take several minutes. When the registration
  • Hitachi CP-X2514WN | User Manual - Page 49
    SCREEN menu Item MyScreen Lock MESSAGE Description Using the ▲/▼ buttons turns on/off the MyScreen lock function. ON ó OFF When the ON is selected, the item MyScreen is locked. Use this function for protecting the current MyScreen. • This function cannot be selected when the ON is selected to the
  • Hitachi CP-X2514WN | User Manual - Page 50
    SCREEN menu Item SOURCE NAME Description Each input port for this projector can have a name applied to it. (1) Use the ▲/▼ buttons on the SCREEN menu to select SOURCE NAME and press the ► or ENTER button. The SOURCE
  • Hitachi CP-X2514WN | User Manual - Page 51
    scroll it horizontally when MAP1 or MAP2 is selected. To invert or scroll the map, display the guidance by pressing the RESET button on the remote three seconds or more when MAP1 or MAP2 appears. (continued on next page) 51
  • Hitachi CP-X2514WN | User Manual - Page 52
    required to have NTSC format video or 480i@60 format component video source supporting C.C. feature to utilize this function. It may not work properly, depending is for additional information such as news reports or a TV program guide. The information covers the entire screen. Not all of the C.C.
  • Hitachi CP-X2514WN | User Manual - Page 53
    from the ceiling this feature will not function properly so select the OFF. • This function will be unavailable when the Transition Detector is on (77). Using the ▲/▼ buttons turns on/off the DIRECT POWER ON function. ON  OFF When set to the ON, the lamp in projector will be automatically
  • Hitachi CP-X2514WN | User Manual - Page 54
    99, and when the passed time with no-signal or an unsuitable signal reaches at the set time, the projector lamp will be turned off. If one of the projector's buttons or the remote control buttons is pressed or one of the commands (except get commands) is transmitted to the CONTROL port during the
  • Hitachi CP-X2514WN | User Manual - Page 55
    button on the remote control or the ► button of the projector displays a dialog. To reset the lamp time, select the OK using the ► button. CANCEL  OK • Please reset the lamp time only when you have replaced the lamp, for a suitable indication about the lamp. • For the lamp replacement, see the
  • Hitachi CP-X2514WN | User Manual - Page 56
    of the following functions to MY BUTTON 1/2 on the remote control (6). (1)Use the ▲/▼ buttons on the MY on/off (5. Messenger Function in the Network Guide). When there is no transferred text data Displays SYSTEM_INFORMATION, INPUT_INFORMATION (62), WIRELESS INFORMATION (67), WIRED INFORMATION (
  • Hitachi CP-X2514WN | User Manual - Page 57
    on the remote control. You SERVICE menu. Select an item using the ▲/▼ buttons, and press the ► button or the ENTER button on the remote projector is used at an altitude of about 1600 m or higher, select HIGH. Otherwise, select NORMAL. Note that the projector projector, environment around the projector
  • Hitachi CP-X2514WN | User Manual - Page 58
    OPTION menu Item SERVICE (continued) Description GHOST Adjust the settings using the ▲/▼ accidental operation. REMOTE FREQ. (1)Use the ▲/▼ button to change the projector's remote sensor frequency setting (4, 17). 1:NORMAL ó 2:HIGH (2)Use the ◄/► button to change the projector's remote sensor on
  • Hitachi CP-X2514WN | User Manual - Page 59
    of the projector using the CONTROL port. SERVICE (continued) Guide. COMMUNICATION COMMUNICATION TYPE Select the communication type for transmission via the CONTROL port. NETWORK BRIDGE (WIRELESS network terminal, via this projector from the computer. Select WIRELESS or WIRED as your network
  • Hitachi CP-X2514WN | User Manual - Page 60
    RATE 4800bps ó 9600bps ó 19200bps ó 38400bps PARITY NONE ó ODD ó EVEN SERVICE (continued) • The BAUD RATE is fixed to 19200bps and PARITY is fixed . HALF-DUPLEX ó FULL-DUPLEX HALF-DUPLEX: This method lets the projector make two way communication, but only one direction, either transmitting or
  • Hitachi CP-X2514WN | User Manual - Page 61
    through the CONTROL port. OFF ó 1s ó 2s ó 3s SERVICE (continued) OFF: Select this mode if it is not required to check the responses from the device that the projector COMMUNICATION (continued) sends data to. In this mode, the projector can send out data from the computer continuously. 1s /2s
  • Hitachi CP-X2514WN | User Manual - Page 62
    "INPUT_INFORMATION". It shows the information about the current input. SERVICE (continued) • The "FRAME LOCK" message on the dialog of menus will collectively return to the initial setting. Note that the items LAMP TIME, FILTER TIME, LANGUAGE, FILTER MESSAGE, NETWORK and SECURITY settings are not
  • Hitachi CP-X2514WN | User Manual - Page 63
    settings on this projector may cause trouble on the network remote control to execute the item. Then perform it according to the following table. See the Network Guide for details of NETWORK operation. NOTE • To use the wireless network function of this projector, the designated USB wireless adapter
  • Hitachi CP-X2514WN | User Manual - Page 64
    NETWORK menu Item WIRELESS SETUP (continued) Description Use the ▲/▼ buttons to turn DHCP on/off. can only be used when DHCP is set to OFF. • The IP ADDRESS is the number that identifies this projector on the network. You cannot have two devices with the same IP ADDRESS on the same network. • The
  • Hitachi CP-X2514WN | User Manual - Page 65
    . (3.1.8 Date/Time Settings in the Network Guide) • This setting will be reset if the projector is turned off while STANDBY MODE in the • The available channels would be various depending on a country. In addition, wireless network card might be required due to the standard. • This item can only
  • Hitachi CP-X2514WN | User Manual - Page 66
    NETWORK menu Item WIRELESS SETUP (continued) SSID (continued on next page) 66 Description Use the ▲/▼ buttons to select the SSID to display the SSID menu. #1 DEFAULT  #2 DEFAULT  #3 DEFAULT #5 CUSTOM  #4
  • Hitachi CP-X2514WN | User Manual - Page 67
    wireless LAN connection devices. WIRELESS INFORMATION • For details of PASSCODE, refer to the manual for "LiveViewer". • Nothing (blank) is shown in the PROJECTOR condition. (1) The USB wireless adapter is not inserted into the projector. (2) DHCP is ON and the projector does not get address from
  • Hitachi CP-X2514WN | User Manual - Page 68
    ▲/▼ buttons to select an item, and the ► or ENTER button on the remote control to perform the item. WIRED SETUP Use the ▲/▼ buttons to turn DHCP is set to OFF. • The IP ADDRESS is the number that identifies this projector on the network. You cannot have two devices with the same IP ADDRESS on
  • Hitachi CP-X2514WN | User Manual - Page 69
    item in the WIRELESS SETUP menu is overwritten with the same setting (65). • The projector will override this Settings in the Network Guide) • This setting will be reset if the projector is turned off while STANDBY the manual for "LiveViewer". • Only the first 16 characters of the PROJECTOR NAME
  • Hitachi CP-X2514WN | User Manual - Page 70
    ENTER or INPUT button, 1 character or all characters will be erased.The PROJECTOR NAME can be input up to 64 characters. (3) To change an already and press the ►, ENTER or INPUT button. To revert to the previous PROJECTOR NAME without saving changes, move the cursor to the CANCEL on screen and press
  • Hitachi CP-X2514WN | User Manual - Page 71
    It can be downloaded from the Hitachi web site. Use the ▲/▼ buttons to select an MY IMAGE (4. My Image Function in the Network Guide) and the ► or ENTER button to display remote control. To erase the image displayed and its source file in the projector. (1) P ress the RESET button on the remote
  • Hitachi CP-X2514WN | User Manual - Page 72
    .com). For details of Network Presentation and instructions to install the "LiveViewer", refer to the manual for "LiveViewer". PRESENTATION QUIT PRESENTER MODE If you set a computer to the Presenter mode while its image is projected, the projector is occupied by the computer and access from
  • Hitachi CP-X2514WN | User Manual - Page 73
    can set user names for each computer on "LiveViwer". For details, refer to the manual for "LiveViewer". Executing this item restarts and initializes the network functions. Choose the RESTART EXECUTE using the button ►. SERVICE Then use the button ► to execute. Network will be once cut off when
  • Hitachi CP-X2514WN | User Manual - Page 74
    registered password. The factory default password is as follows. CP-X2514WN, CP-X3014WN, CP-X4014WN: 3292 CP-WX3014WN: 1692 This password can be changed (below). this time. Pressing the ENTER button on the remote control or ► button on the projector will close the NOTE NEW PASSWORD box. • Please do
  • Hitachi CP-X2514WN | User Manual - Page 75
    PASSWORD box for about 30 seconds, please make note of the password during this time. Pressing the ENTER button on the remote control or ► button on the projector will return to MyScreen PASSWORD on/off menu. When a password is set for MyScreen: • The MyScreen registration function (and menu
  • Hitachi CP-X2514WN | User Manual - Page 76
    the Enter PIN code box is displayed. This function will activate only when the projector is started after AC power is turned off. • Please do not forget your LOCK function off. If an incorrect PIN code is input 3 times, the projector will turn off. 3 If you have forgotten your PIN code 3-1 While
  • Hitachi CP-X2514WN | User Manual - Page 77
    projector will not display the input signal. • To display the signal again, set this function OFF. • After about 5 minutes of displaying the TRANSITION DETECTOR ON alarm, the lamp Pressing the ENTER button on the remote control or the ► button on the projector will return to the TRANSITION DETECTOR
  • Hitachi CP-X2514WN | User Manual - Page 78
    NEW PASSWORD box for about 30 seconds, then please make note of the password during this time. Pressing the ENTER button on the remote control or ► button on the projector will return to the MY TEXT PASSWORD on/off menu. 2 Turning off the MY TEXT PASSWORD 2-1 Follow the procedure in 1-1 to
  • Hitachi CP-X2514WN | User Manual - Page 79
    When it is set ON, the MY TEXT will be displayed on the START UP screen and the INPUT_ INFORMATION when the INFORMATION on the SERVICE menu is chosen. • This function is available only when the MY TEXT PASSWORD function is set to the OFF. (1) U se the ▲/▼ buttons on the SECURITY
  • Hitachi CP-X2514WN | User Manual - Page 80
    Presentation tools Presentation tools The projector has the following two convenient tools that enable on- mode (85) - Slideshow mode (87) [Supported storage media] • USB memory (USB memory type, USB hard disk and USB card reader type) NOTE • USB readers (adapters) that have more than one USB slot
  • Hitachi CP-X2514WN | User Manual - Page 81
    NOTE • Files with a resolution larger than the following are not supported. CP-X2514WN, CP-X3014WN,CP-X4014WN: 1024 x 768 (Still)，768 x 576 (Movie) CP-WX3014WN: 1280 x 800 (Still)，768 x 576 (Movie) (* Some computers may not support 1280 x 800.) • Files with a resolution smaller than 36 x 36 are
  • Hitachi CP-X2514WN | User Manual - Page 82
    the images on the Thumbnail screen with the remote control, control panel or Web Remote Control. The following functions can be supported while the Thumbnail is displayed. Button operation The remote control Control panel Web Remote Control PAGE UP PAGE DOWN - [PAGE UP] [PAGE
  • Hitachi CP-X2514WN | User Manual - Page 83
    the Slideshow mode. Switches the input port. Displays the menu. Be sure to use this function before removing USB storage device from the projector. After that, the projector will not recognize a USB storage device until you insert it again into the USB TYPE A input port. Turns the sound on/off for
  • Hitachi CP-X2514WN | User Manual - Page 84
    Presentation (continued) NOTE • These operations are not accessible while the projector OSD is displayed. • The Thumbnail mode is able to display the Thumbnail. This file seems to be broken or not supported format. A file that cannot be displayed on the thumbnail screen is indicated by a file format icon.
  • Hitachi CP-X2514WN | User Manual - Page 85
    still images The following operations are enabled in the Full Screen mode while a still image is displayed. Button operation The remote control Control panel Web Remote Control ▼ ► or PAGE DOWN ▼ or ► [▼] [►] or [PAGE DOWN] ▲ ◄ or PAGE UP ▲ or ◄ [▲] [◄] or [PAGE UP] ENTER INPUT [ENTER
  • Hitachi CP-X2514WN | User Manual - Page 86
    are enabled while the remote control icon and progress bar are displayed. Button operation The remote control Control panel Web Remote Control ▲ ▲ [▲] the previous file. NOTE • These operations are not accessible while the projector OSD is displayed. • It is not possible to change the input
  • Hitachi CP-X2514WN | User Manual - Page 87
    Full Screen mode are enabled when movies are displayed. The remote control ENTER Button operation Control panel Web Remote Control INPUT [ENTER] Functions Displays thumbnail NOTE • These operations are not accessible while the projector OSD is displayed. • It is not possible to change the
  • Hitachi CP-X2514WN | User Manual - Page 88
    Presentation tools PC-LESS Presentation (continued) You can play the Slideshow at your desired configuration. Configure the Slideshow items in the Thumbnail. 1) RETURN : Returns to the thumbnail mode. 2) PLAY : P lay the Slideshow. 3) START : Set the beginning number of the Slideshow. 4)
  • Hitachi CP-X2514WN | User Manual - Page 89
    Presentation tools PC-LESS Presentation (continued) Playlist The Playlist is a DOS format text file, which decides the order of displayed still image files in the Thumbnail or Slideshow. The playlist file name is "playlist.txt" and it can be edited on a computer. It is created in the folder that
  • Hitachi CP-X2514WN | User Manual - Page 90
    USB TYPE B port on the projector using a USB cable, the projector will be recognized as a CD-ROM drive on your computer. Then, the software for the latest version of the software and its manual. (&User's Manual (concise)) Follow the instructions that can be obtained at the site for updating. (continued
  • Hitachi CP-X2514WN | User Manual - Page 91
    " (refer to the Network Guide) and this application cannot be used at the same time. If you connect your computer to the projector by using a USB cable computer, make the firwall function invalid with following the user's manual. • Some security software may block image transmission. Please change
  • Hitachi CP-X2514WN | User Manual - Page 92
    the button is clicked is remained on the screen. You can revise the image data on your computer without showing it on the projector's screen.  Option button The Options window is displayed.  Minimize button The Floating menu is closed, and the icon reappears in the Windows notification
  • Hitachi CP-X2514WN | User Manual - Page 93
    over Speed. It makes JPEG compression rate lower. The screen on the projector is rewritten slower because the transferred data is larger, but the image be faster. CP-X2514WN, CP-X3014WN, CP-X4014WN: 1024 x 768 (XGA) CP-WX3014WN: 1280 x 800 If your computer does not support the display resolution
  • Hitachi CP-X2514WN | User Manual - Page 94
    number. Type number : DT01021 Replacing the lamp lamp cover 3 1. Turn the projector off, and unplug the power cord. Allow the projector to cool for at least 45 minutes. 2. Prepare a new lamp. If the projector is mounted on a ceiling, or if the lamp has broken, also ask the dealer to replace
  • Hitachi CP-X2514WN | User Manual - Page 95
    • Never unscrew except the appointed (marked by an arrow) screws. • Do not open the lamp cover while the projector is suspended from a ceiling. This is dangerous, since if the lamp's bulb has broken, the shards will fall out when the cover is opened. In addition, working in high places is dangerous
  • Hitachi CP-X2514WN | User Manual - Page 96
    will come together with a replacement lamp for this projector. 1. Turn the projector off, and unplug the power cord. Allow the projector to sufficiently cool down. Filter cover 2 2. Use a vacuum cleaner on and around the filter cover. 3. While supporting the projector with one hand, use your
  • Hitachi CP-X2514WN | User Manual - Page 97
    the air filter when it is damaged or heavily soiled. • When you replace the projection lamp, please replace the air filter. An air filter of specified type will come together with a replacement lamp for this projector. • Please reset the filter time only when you have cleaned or replaced the air
  • Hitachi CP-X2514WN | User Manual - Page 98
    not touch the lens directly with your hand. Caring for the cabinet and remote control Incorrect care could have adverse influence such as discoloration, peeling paint, etc. 1. Turn the projector off, and unplug the power cord. Allow the projector to cool sufficiently. 2. After making sure that the
  • Hitachi CP-X2514WN | User Manual - Page 99
    Troubleshooting Troubleshooting If an abnormal operation should occur, stop using the projector contact to your dealer or service company. Otherwise if a problem occurs with the projector, the following checks and specs for your projector or the signal source specs. An improper signal is input
  • Hitachi CP-X2514WN | User Manual - Page 100
    Troubleshooting Related messages (continued) Message Description The internal temperature is rising. Please turn the power off, and allow the projector FAN SPEED of SERVICE in the OPTION menu (57). If the projector is used with a wrong setting, it may cause damage to the projector itself or the
  • Hitachi CP-X2514WN | User Manual - Page 101
    Troubleshooting Regarding the indicator lamps When operation of the LAMP, TEMP and POWER indicators differs from usual, check and cope with it according to the following table. POWER LAMP TEMP indicator indicator indicator Description Lighting Turned Turned The projector is in a standby state.
  • Hitachi CP-X2514WN | User Manual - Page 102
    Troubleshooting Regarding the indicator lamps (continued) POWER indicator Blinking In Red or Lighting In Red LAMP TEMP indicator indicator the lamp and lamp cover, and then turn the power on again. If the projector is used at an altitude of about 1600 m or higher, set FAN SPEED of the SERVICE item
  • Hitachi CP-X2514WN | User Manual - Page 103
    Troubleshooting Resetting all settings When it is hard to correct some wrong settings, the FACTORY RESET function of SERVICE item in OPTION menu (62) can reset all settings (except settings such as LANGUAGE, LAMP TIME, FILTER TIME, FILTER MESSAGE, SECURITY and NETWORK) to the factory default. Be
  • Hitachi CP-X2514WN | User Manual - Page 104
    Troubleshooting 32 function. No pictures are displayed. The computer cannot detect the projector as a plug and play monitor. Make sure that the computer play monitor. The BLANK screen is displayed. Press BLANK button on the remote control. 27 The USB TYPE B port is selected as the picture input
  • Hitachi CP-X2514WN | User Manual - Page 105
    Troubleshooting Phenomena that may be easy to be mistaken for machine defects (continued) Phenomenon No pictures are displayed. (continued) Cases not involving a machine defect The projector the SETUP menu. The lamp is approaching the end of its product lifetime. Replace the lamp. 94 ~ 95
  • Hitachi CP-X2514WN | User Manual - Page 106
    . 21, 45 Noise can be heard when the MIC port is connected. If a microphone is connected to the projector while the USB wireless adapter is connected to the projector, noise from the adapter caused by interference is output from the speakers. Input the signal at line level using a preamp, etc. or
  • Hitachi CP-X2514WN | User Manual - Page 107
    Select NETWORK BRIDGE for COMMUNICATION TYPE item in the OPTION - SERVICE - COMMUNICATION 59 menu. The SAVING function is working. Select AND TIME setting for WIRELESS SETUP or WIRED SETUP in the NETWORK menu. 65, 69 Disconnect the LAN cable and check that the projector is working properly.
  • Hitachi CP-X2514WN | User Manual - Page 108
    Specifications Specifications Please see the Specifications in the User's Manual (concise) which is a book. End User License Agreement for the Projector Software • Software in the projector consists of the plural number of independent software modules and there exist our copyright or/and third party
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
1
Projector
CP-X2514WN/CP-X3014WN/
CP-X4014WN/CP-WX3014WN
User's Manual (detailed)
Operating Guide
Thank you for purchasing this projector.
►Before using this product, please read all manuals for this
product. Be sure to read
Safety Guide
first. After reading them, store them in a
safe place for future reference.
WARNING
• The information in this manual is subject to change without notice.
• The manufacturer assumes no responsibility for any errors that may appear in
this manual.
• The reproduction, transfer or copy of all or any part of this document is not
permitted without express written consent.
NOTE
Trademark acknowledgment
Various symbols are used in this manual. The meanings of these symbols are
described below.
About this manual
WARNING
CAUTION
This symbol indicates information that, if ignored, could possibly
result in personal injury or even death due to incorrect handling.
This symbol indicates information that, if ignored, could possibly
result in personal injury or physical damage due to incorrect
handling.
Please refer to the pages written following this symbol.
• Mac
®
is a registered trademark of Apple Inc.
• Windows
®
, DirectDraw
®
and Direct3D
®
are registered trademarks of Microsoft Corporation
in the U.S. and/or other countries.
• VESA and DDC are trademarks of the Video Electronics Standard Association.
•
HDMI, the HDMI logo, and High-Definition Multimedia Interface are trademarks or registered
trademarks of HDMI Licensing LLC in the United States and other countries.
• Trademark PJLink is a trademark applied for trademark rights
in Japan, the United States of America and other countries and
areas.
• Blu-ray Disc
TM
is a trademark.
All other trademarks are the properties of their respective owners.
NOTICE
This entry notices of fear of causing trouble.