Hitachi CP-X3014WN User Manual

Hitachi CP-X3014WN Manual

Get Hitachi CP-X3014WN PDF manuals and user guides View all Hitachi CP-X3014WN manuals
Add to My Manuals
Save this manual to your list of manuals

Hitachi CP-X3014WN manual content summary:

  • Hitachi CP-X3014WN | User Manual - Page 1
    Projector CP-X2514WN/CP-X3014WN/ CP-X4014WN/CP-WX3014WN User's Manual (detailed) Operating Guide Thank you for purchasing this projector. WARNING ►Before using this product, please read all manuals for this product. Be sure to read Safety Guide first. After reading them, store them in a safe place
  • Hitachi CP-X3014WN | User Manual - Page 2
    . . 18 USB TYPE B, LAMP TIME, FILTER TIME, Power on/off 19 MY BUTTON, MY SOURCE, SERVICE Turning on the power 19 NETWORK menu 63 Turning off the power 19 WIRELESS SETUP, WIRELESS INFORMATION, Operating 20 WIRED SETUP, WIRED INFORMATION, Adjusting the volume 20 PROJECTOR NAME, MY IMAGE
  • Hitachi CP-X3014WN | User Manual - Page 3
    wireless LAN connection. The built-in 16W speaker can deliver sufficient sound volume in a large space like a classroom without external speakers. Checking the contents of package Please see the Contents of package section in the User's Manual (concise) which is a book. Your projector should
  • Hitachi CP-X3014WN | User Manual - Page 4
    not open or remove any portion of the product, unless the manuals direct it. ►Do not subject the projector to unstable conditions. ►Do not apply a shock or pressure to lens and the openings on the projector while the lamp is on. CAUTION ►Do not touch around the lamp cover and the exhaust vents during
  • Hitachi CP-X3014WN | User Manual - Page 5
    Introduction Part names (continued) Control panel (1) STANDBY/ON button ( 19) (2) INPUT button ( 21) (3) MENU button ( 28) (4) LAMP indicator ( 101) (5) TEMP indicator ( 101) (6) POWER indicator ( 101) (5) (4) (1) (2) (3) (6) Rear panel ( 10 ~ 14) (1) LAN port (2) USB TYPE A port (3) HDMI
  • Hitachi CP-X3014WN | User Manual - Page 6
    Introduction Part names (continued) Remote control (1) VIDEO button ( 21) (2) COMPUTER button ( 21) (3) SEARCH button ( 22) (4) STANDBY/ON button ( 19) (5) ASPECT button ( 22) (6) AUTO button ( 24) (7) BLANK button ( 27) (8) MAGNIFY - ON button ( 26) (9) MAGNIFY - OFF button ( 26) (10) MY SOURCE/DOC
  • Hitachi CP-X3014WN | User Manual - Page 7
    installation in a special state such as ceiling mount, the specified mounting accessories ( Specifications in the User's Manual (concise)) and service may be required. Before installing the projector, consult your dealer about your installation. Arrangement Refer to tables T-1 and T-2 at the back of
  • Hitachi CP-X3014WN | User Manual - Page 8
    a wobbly table or cart, or a surface that is smaller than the projector. • Do not put the projector on its side, front or rear position. • Do not attach nor place anything on the projector unless otherwise specified in the manual. • Do not use any mounting accessories except the accessories specified
  • Hitachi CP-X3014WN | User Manual - Page 9
    and could be deposited in the projector causing image degradation or other problems. • Do not place the projector in a smoking area, kitchen, SERVICE in the OPTION menu according to the usage environment ( 57). If the projector is used with a wrong setting, it may cause damage to the projector
  • Hitachi CP-X3014WN | User Manual - Page 10
    the devices are turned off, perform the connection, according to the following instructions. Refer to the figures in subsequent pages. Before connecting the projector to a network system, be sure to read Network Guide too. WARNING ►Use only the appropriate accessories. Otherwise it could cause a fire
  • Hitachi CP-X3014WN | User Manual - Page 11
    manual and check the compatibility of the signal level, the synchronization methods and the display resolution output to the projector. - Some signal may need an adapter to input this projector. - Some computers have multiple screen display modes that may include some signals which are not supported
  • Hitachi CP-X3014WN | User Manual - Page 12
    secure your data ( 83). ►Do not use any extension cable or device when connecting the adapter to the projector. Before you insert or pull out the USB wireless adapter from the projector, turn off the power of the projector and pull out the power cord's plug from the outlet. Do not touch the USB
  • Hitachi CP-X3014WN | User Manual - Page 13
    39) NOTE • The HDMI port of this model is compatible with HDCP (High-bandwidth Digital Content Protection DVD players or the like. - The HDMI supports the following signals. Video signal : 480i@ to input 1080p@50/60 signal to the projector. - When the projector is connected with a device having DVI
  • Hitachi CP-X3014WN | User Manual - Page 14
    microphone, even while the sound from the projector is output. You can input line level signal to the MIC port from equipment such as wireless microphone. Select HIGH in the MIC LEVEL of the microphone and the projector ( 20). • This projector doesn't support plug-in power for the microphone. 14
  • Hitachi CP-X3014WN | User Manual - Page 15
    ON function activated ( 53), the connection of the power supply make the projector turn on. AC IN Power cord WARNING ►Please use extra caution when cord with a wet hand. • Only use the power cord that came with the projector. If it is damaged, consult your dealer to get a new one. Never modify the
  • Hitachi CP-X3014WN | User Manual - Page 16
    supplied adapter cover to prevent the USB wireless adapter from coming off easily. 1. wire can be attached to the security bar on the projector. Refer to the figure to choose an anti-theft slot for the Kensington lock. For details, see the manual of the security tool. 11.7mm Security slot 17.5mm
  • Hitachi CP-X3014WN | User Manual - Page 17
    replace HITACHI MAXELL, Part No.LR6 or R6P) according to their plus and minus terminals as indicated in the remote control. 3. Replace out the leakage and then replace a battery. If the leakage projector's remote sensor. This projector signals to the projector (Class 1 signal to the projector. • The
  • Hitachi CP-X3014WN | User Manual - Page 18
    in the SERVICE item of the OPTION menu ( 58) of the projector to be check your computer's manuals before connecting this computer's configurations and mouse drivers. This function can work with projector is working properly. This function is not available in any of the following cases: - While the lamp
  • Hitachi CP-X3014WN | User Manual - Page 19
    . The message "Power off?" will appear on the screen for about 5 seconds. 2. Press the STANDBY/ON button again while the message appears. The projector lamp will go off, and the POWER indicator will begin blinking in orange. Then POWER indicator will stop blinking and light in steady orange when the
  • Hitachi CP-X3014WN | User Manual - Page 20
    picture input port, the volume MY BUTTON KEYSTONE   MUTE adjustment is disabled. Please see AUDIO SOURCE item of AUDIO menu ( 45). ● Even if the projector is in the standby mode, the volume is adjustable when both of the following conditions are true: - An option other than is selected for
  • Hitachi CP-X3014WN | User Manual - Page 21
    seconds to project the images from the USB TYPE B port. 1. Press COMPUTER button on the remote control. Each time you press the button, the projector switches its input port from the current port as below. COMPUTER IN1 COMPUTER IN2 LAN USB TYPE B USB TYPE A COMPUTER button VIDEO COMPUTER MY
  • Hitachi CP-X3014WN | User Manual - Page 22
    button, the projector switches the mode for aspect ratio in turn. ASPECT button VIDEO COMPUTER MY SOURCE/ DOC.CAMERA For a computer signal CP-X2514WN, CP-X3014WN, CP-X4014WN: NORMAL 4:3 16:9 16:10 ASPECT AUTO SEARCH BLANK MAGNIFY FREEZE PAGE VOLUME ON UP 㧗 OFF DOWN ࡯ CP-WX3014WN: NORMAL
  • Hitachi CP-X3014WN | User Manual - Page 23
    4. After making sure that the elevator feet are locked, put the projector down gently. To finely 5. If necessary, the elevator feet can be manually adjust, twist the foot. twisted to make more precise adjustments. Hold the projector when twisting the feet. CAUTION ►Do not handle the elevator
  • Hitachi CP-X3014WN | User Manual - Page 24
    position and horizontal position will be automatically set to the default. The horizontal phase will be automatically adjusted. ● The automatic on the PC model. ● The items adjusted by this function may vary when the FINE or DISABLE is selected for the AUTO ADJUST item of the SERVICE item in the
  • Hitachi CP-X3014WN | User Manual - Page 25
    following. (1) AUTO executes automatic vertical keystone correction. (2) MANUAL displays a dialog for keystone correction. Use the ◄/► buttons is selected to the MIRROR item in the SETUP menu, if the projector screen is inclined or angled downward, automatic vertical keystone correction may not
  • Hitachi CP-X3014WN | User Manual - Page 26
    will appear on the screen. When the MAGNIFY ON button is pressed for the first time after the projector is turned on, the picture will be zoomed by 1.5 times. On the dialog, triangle marks to in the following cases: - A sync signal in the range not supported is input. - There is no input signal. 26
  • Hitachi CP-X3014WN | User Manual - Page 27
    If the projector continues projecting a still image for a long time, the LCD panel might possibly be burned in. Do not leave the projector in blank screen while the projector's lamp is on, use the BLANK function above. Taking any other action may cause the damage on the projector. NOTE • The sound
  • Hitachi CP-X3014WN | User Manual - Page 28
    of these menus is operated using the same methods. While the projector is displaying any menu, the MENU button on the projector works as the cursor buttons. The basic operations of these item will appear. (3) Use the buttons as instructed in the OSD to operate the item. (continued on next page) 28
  • Hitachi CP-X3014WN | User Manual - Page 29
    Operating Using the menu function (continued) 3. To close the MENU, press the MENU button again or select EXIT and press the ◄ cursor button or ENTER button. Even if you do not do anything, the dialog will automatically disappear after about 30 seconds. ● If you want to move the menu position, use
  • Hitachi CP-X3014WN | User Manual - Page 30
    ) DAYTIME WHITEBOARD BOARD(GREEN) PICTURE MODE NORMAL CINEMA DYNAMIC BOARD(BLACK) BOARD(GREEN) WHITEBOARD DAYTIME GAMMA 1 DEFAULT 2 DEFAULT 3 DEFAULT 4 DEFAULT 4 DEFAULT 5 DEFAULT 6 DEFAULT COLOR TEMP 2 MID 3 LOW 1 HIGH 4 Hi-BRIGHT-1 5 Hi-BRIGHT-2 2 MID 6 Hi-BRIGHT-3 • When the combination of
  • Hitachi CP-X3014WN | User Manual - Page 31
    EASY MENU Item Description ECO MODE Using the ◄/► buttons turns off/on the Eco mode. See the ECO MODE item in SETUP menu ( 43). MIRROR Using the ◄/► buttons switches the mode for mirror status. See the MIRROR item in SETUP menu ( 43). RESET Performing this item resets all of the EASY MENU
  • Hitachi CP-X3014WN | User Manual - Page 32
    buttons adjusts the contrast. Weak Strong Using the ▲/▼ buttons switches the gamma mode. 1 DEFAULT 1 CUSTOM 2 DEFAULT 2 CUSTOM 3 DEFAULT 6 CUSTOM 3 CUSTOM 6 DEFAULT 5 CUSTOM 5 DEFAULT 4 CUSTOM 4 DEFAULT GAMMA To adjust CUSTOM Selecting a mode whose name includes CUSTOM and then pressing the
  • Hitachi CP-X3014WN | User Manual - Page 33
    applies. (1) HDMI FORMAT item in the INPUT menu is set to VIDEO. (2) HDMI FORMAT item in the INPUT menu is set to AUTO, and the projector recognizes that it receives video signals. TINT Using the ◄/► buttons adjusts the tint. Reddish Greenish • This item can be selected only for a video, s-video
  • Hitachi CP-X3014WN | User Manual - Page 34
    : The active iris is always open. • The screen may flicker when the PRESENTATION or THEATER modes are selected. If this occurs select OFF. This projector has 4 memories for adjustment data (for all the items of the PICTURE menu). Selecting a function using the ▲/▼ buttons and pressing the ► or ENTER
  • Hitachi CP-X3014WN | User Manual - Page 35
    USB TYPE A or USB TYPE B port, or if there is no signal CP-X2514WN, CP-X3014WN, CP-X4014WN: 4:3 (fixed) CP-WX3014WN: 16:10 (fixed) • The NORMAL mode keeps the original aspect ratio of the menu is set to AUTO, and the projector recognizes that it receives video signals. (continued on next page) 35
  • Hitachi CP-X3014WN | User Manual - Page 36
    noise to appear on the screen. If this occurs, please reset the vertical position to the default setting. Pressing the RESET button when the V POSITION is selected will reset the V POSITION to the default setting. • When this function is performed on a video signal or an s-video signal, the range of
  • Hitachi CP-X3014WN | User Manual - Page 37
    set to the default. For a component video signal The vertical position and position will be automatically set to the default. The horizontal phase will be automatically adjusted the edge of the screen, depending on the PC model. • The items adjusted by this function may vary when the FINE or
  • Hitachi CP-X3014WN | User Manual - Page 38
    / Pb, Cr/Pr) and VIDEO ports will function as a SCART RGB port. A SCART adapter or SCART cable is required for a SCART RGB input to the projector. For details, contact your dealer. (continued on next page) 38
  • Hitachi CP-X3014WN | User Manual - Page 39
    INPUT menu Item VIDEO FORMAT Description The video format for S-VIDEO port and VIDEO port can be set. (1) Use the ▲/▼ buttons to select the input port. (2) Using the ◄/► buttons switches the mode for video format. AUTO NTSC PAL SECAM N-PAL M-PAL NTSC4.43 • This item is performed only for a video
  • Hitachi CP-X3014WN | User Manual - Page 40
    INPUT menu Item COMPUTER IN FRAME LOCK Description The computer input signal type for COMPUTER IN1 and IN2 ports can be set. (1) Use the ▲/▼ buttons to select the COMPUTER IN port to be set. (2) Use the ◄/► buttons to select the computer input signal type. AUTO SYNC ON G OFF • Selecting the AUTO
  • Hitachi CP-X3014WN | User Manual - Page 41
    COMPUTER IN1 and COMPUTER IN2 input signals can be set on this projector. (1) In the INPUT menu select the RESOLUTION using the ▲/▼ vertical (VERT) resolutions using CUSTOM ↓ the buttons. This function may not support all resolutions. (5) Move the cursor to OK on screen and press the
  • Hitachi CP-X3014WN | User Manual - Page 42
    For some input, this function may not work well. • When V:INVERT or H&V:INVERT is selected to the MIRROR item in the SETUP menu, if the projector screen is inclined or angled AUTO KEYSTONE downward, this function may not work correctly. • When the zoom adjustment is set to the TELE (telephoto focus
  • Hitachi CP-X3014WN | User Manual - Page 43
    at start-up regardless of the ECO MODE ( below) setting. An OSD message "AUTO ECO MODE" will be displayed for tens of seconds when the projector starts with this function activated. Using the ▲/▼ buttons turns off/on the Eco mode. NORMAL ECO ECO MODE • When the ECO is selected, acoustic noise
  • Hitachi CP-X3014WN | User Manual - Page 44
    with some functional restriction as below: • When SAVING is selected, the RS-232C communication control except to turn the projector on and the network function are disabled while the projector is in the standby mode. If the COMMUNICATION TYPE in the COMMUNICATION menu is set to NETWORK BRIDGE, all
  • Hitachi CP-X3014WN | User Manual - Page 45
    projected, the audio signal from the input port selected in step (2) is output to both the AUDIO OUT port and built-in speaker of this projector. However, the built-in speaker does not work when SPEAKER is set to OFF. (1) Choose a picture input port using the ▲/▼ buttons. Choose STANDBY to select
  • Hitachi CP-X3014WN | User Manual - Page 46
    AUDIO menu Item HDMI AUDIO MIC LEVEL MIC VOLUME Description Using the ▲/▼ buttons switches the mode for the HDMITM audio. Check each of the two modes provided and select the suitable one for your HDMITM audio device. 1 2 Using the ▲/▼ buttons switches the input level to match that of the
  • Hitachi CP-X3014WN | User Manual - Page 47
    . If also the BLANK screen is the MyScreen or ORIGINAL, the plain black screen is instead used. • When the ON is selected to the MyScreen PASSWORD item in the SECURITY menu ( 75), the START UP is fixed to MyScreen. (continued on next page) 47
  • Hitachi CP-X3014WN | User Manual - Page 48
    selected when the ON is selected to the MyScreen Lock item ( 49). • This function cannot be selected when the ON is selected to the MyScreen PASSWORD item in SECURITY menu ( 75). • This function is unavailable for a signal from the LAN, USB TYPE A, USB TYPE B or HDMI port. (continued on next page
  • Hitachi CP-X3014WN | User Manual - Page 49
    MyScreen is locked. Use this function for protecting the current MyScreen. • This function cannot be selected when the ON is selected to the MyScreen PASSWORD item in SECURITY menu ( 75). Using the ▲/▼ buttons turns on/off the message function. ON OFF When the ON is selected, the following message
  • Hitachi CP-X3014WN | User Manual - Page 50
    SCREEN menu Item SOURCE NAME Description Each input port for this projector can have a name applied to it. (1) Use the ▲/▼ buttons on the SCREEN menu to select SOURCE NAME and press the ► or ENTER button. The SOURCE
  • Hitachi CP-X3014WN | User Manual - Page 51
    SCREEN menu Item SOURCE NAME (continued) TEMPLATE Description (6) The current name will be displayed on the first line. Use the buttons and the ENTER or INPUT button to select and enter characters. To erase 1 character at one time, press the RESET button or press the ◄ and INPUT button at the same
  • Hitachi CP-X3014WN | User Manual - Page 52
    required to have NTSC format video or 480i@60 format component video source supporting C.C. feature to utilize this function. It may not work properly, depending on is for additional information such as news reports or a TV program guide. The information covers the entire screen. Not all of the C.C.
  • Hitachi CP-X3014WN | User Manual - Page 53
    not work as long as the power has been supplied to the projector while the lamp is off. • After turning the lamp on by the DIRECT POWER ON function, if neither input nor operation is detected for about 30 minutes, the projector is turned off, even though the AUTO POWER OFF function ( 54) is
  • Hitachi CP-X3014WN | User Manual - Page 54
    to 1 to 99, and when the passed time with no-signal or an unsuitable signal reaches at the set time, the projector lamp will be turned off. If one of the projector's buttons or the remote control buttons is pressed or one of the commands (except get commands) is transmitted to the CONTROL
  • Hitachi CP-X3014WN | User Manual - Page 55
    button of the projector displays a dialog. To reset the lamp time, select the OK using the ► button. CANCEL OK • Please reset the lamp time only when you have replaced the lamp, for a suitable indication about the lamp. • For the lamp replacement, see the section Replacing the lamp ( 94). The filter
  • Hitachi CP-X3014WN | User Manual - Page 56
    text displayed on the screen on/off ( 5. Messenger Function in the Network Guide). When there is no transferred text data to display, the message "NO DATA" appears. • INFORMATION: Displays SYSTEM_INFORMATION, INPUT_INFORMATION ( 62), WIRELESS INFORMATION ( 67), WIRED INFORMATION ( 69) or nothing. •
  • Hitachi CP-X3014WN | User Manual - Page 57
    SOURCE SERVICE Description TYPE B Selecting this item displays the SERVICE menu. Select an item using the ▲/▼ projector is used at an altitude of about 1600 m or higher, select HIGH. Otherwise, select NORMAL. Note that the projector cable to the projector, environment around the projector, etc., the
  • Hitachi CP-X3014WN | User Manual - Page 58
    or accidental operation. REMOTE FREQ. (1) Use the ▲/▼ button to change the projector's remote sensor frequency setting ( 4, 17). 1:NORMAL 2:HIGH (2) Use the ◄/► button to change the projector's remote sensor on or off. ON OFF The factory default setting is for both 1:NORMAL and 2:HIGH to be on. If
  • Hitachi CP-X3014WN | User Manual - Page 59
    projector using the CONTROL port. SERVICE WIRELESS or WIRED as your network connection mode. The CONTROL port doesn't accept RS-232C commands ( 6. Network Bridge Function in the Network Guide) OFF: Select this mode to receive RS-232C commands using the CONTROL port. • OFF is selected as the default
  • Hitachi CP-X3014WN | User Manual - Page 60
    port. BAUD RATE 4800bps 9600bps 19200bps 38400bps PARITY NONE ODD EVEN SERVICE (continued) • The BAUD RATE is fixed to 19200bps and PARITY method lets the projector make two way communication, transmitting and receiving data at the same time. • HALF-DUPLEX is selected as the default setting. • If
  • Hitachi CP-X3014WN | User Manual - Page 61
    the HALF-DUPLEX through the CONTROL port. OFF 1s 2s 3s SERVICE (continued) OFF: Select this mode if it is not required to check the responses from the device that the projector COMMUNICATION sends data to. In this mode, the projector can (continued) send out data from the computer continuously
  • Hitachi CP-X3014WN | User Manual - Page 62
    "INPUT_INFORMATION". It shows the information about the current input. SERVICE (continued) • The "FRAME LOCK" message on the dialog of menus will collectively return to the initial setting. Note that the items LAMP TIME, FILTER TIME, LANGUAGE, FILTER MESSAGE, NETWORK and SECURITY settings are not
  • Hitachi CP-X3014WN | User Manual - Page 63
    menu Remember that incorrect network settings on this projector may cause trouble on the network. Be sure to consult table. See the Network Guide for details of NETWORK operation. NOTE • To use the wireless network function of this projector, the designated USB wireless adapter that is sold as
  • Hitachi CP-X3014WN | User Manual - Page 64
    Item WIRELESS OFF. • The IP ADDRESS is the number that identifies this projector on the network. You cannot have two devices with the same IP ADDRESS . • The SUBNET MASK "0.0.0.0" is prohibited. DEFAULT GATEWAY Use the buttons to enter the DEFAULT GATEWAY (a node on a computer network that serves
  • Hitachi CP-X3014WN | User Manual - Page 65
    ( 3.1.8 Date/Time Settings in the Network Guide) • This setting will be reset if the projector is turned off while STANDBY MODE in the • The available channels would be various depending on a country. In addition, wireless network card might be required due to the standard. • This item can only
  • Hitachi CP-X3014WN | User Manual - Page 66
    NETWORK menu Item WIRELESS SETUP (continued) SSID (continued on next page) 66 Description Use the ▲/▼ buttons to select the SSID to display the SSID menu. #1 DEFAULT #2 DEFAULT #3 DEFAULT #5 CUSTOM #4 DEFAULT Select one of the DEFAULT (#1~#4) and press ► or ENTER button. To adjust CUSTOM
  • Hitachi CP-X3014WN | User Manual - Page 67
    settings. The second and subsequent pages display the signal information of wireless LAN connection devices. WIRELESS INFORMATION • For details of PASSCODE, refer to the manual for "LiveViewer". • Nothing (blank) is shown in the PROJECTOR NAME ( 70) and SSID ( 66) field until you setup those items
  • Hitachi CP-X3014WN | User Manual - Page 68
    server. • Auto IP function will be assigned an IP address if the projector could not obtain an IP address from server even if DHCP is "ON". OFF. • The SUBNET MASK "0.0.0.0" is prohibited. DEFAULT GATEWAY Use the buttons to enter the DEFAULT GATEWAY (a node on a computer network that serves
  • Hitachi CP-X3014WN | User Manual - Page 69
    same item in the WIRELESS SETUP menu is overwritten with Guide) • This setting will be reset if the projector manual for "LiveViewer". • Only the first 16 characters of the PROJECTOR NAME are displayed. • IP ADDRESS, SUBNET MASK and DEFAULT GATEWAY indicate "0.0.0.0" when DHCP is ON and the projector
  • Hitachi CP-X3014WN | User Manual - Page 70
    ▲/▼ buttons on the NETWORK menu to select the PROJECTOR NAME and press the ► button. The PROJECTOR NAME dialog will be displayed. (2) The current PROJECTOR NAME will be displayed on the first 3 lines. Particular projector name is pre-assigned by default. Use the buttons and the ENTER or INPUT button
  • Hitachi CP-X3014WN | User Manual - Page 71
    . It can be downloaded from the Hitachi web site. Use the ▲/▼ buttons to select an MY IMAGE ( 4. My Image Function in the Network Guide) and the ► or ENTER button to display the erase the image displayed and its source file in the projector. (1) Press the RESET button on the remote control while
  • Hitachi CP-X3014WN | User Manual - Page 72
    .com). For details of Network Presentation and instructions to install the "LiveViewer", refer to the manual for "LiveViewer". PRESENTATION QUIT PRESENTER MODE If you set a computer to the Presenter mode while its image is projected, the projector is occupied by the computer and access from
  • Hitachi CP-X3014WN | User Manual - Page 73
    . For details, refer to the manual for "LiveViewer". DISPLAY USER NAME Selecting this item displays the user name. This function helps you identify manual for "LiveViewer". Executing this item restarts and initializes the network functions. Choose the RESTART EXECUTE using the button ►. SERVICE
  • Hitachi CP-X3014WN | User Manual - Page 74
    to the SECURITY menu 1. Press the ► button. The ENTER PASSWORD box will be displayed. 2. Use the buttons to enter the registered password. The factory default password is as follows. CP-X2514WN, CP-X3014WN, CP-X4014WN: 3292 CP-WX3014WN: 1692 This password can be changed ( below). Move the cursor to
  • Hitachi CP-X3014WN | User Manual - Page 75
    or ► button on the projector will return to MyScreen PASSWORD on/off menu. When a password is set for MyScreen: • PASSWORD box (large). The 10 digit Inquiring Code will be displayed inside the box. 3-3 Contact your dealer with the 10 digit Inquiring Code. Your password will be sent after your user
  • Hitachi CP-X3014WN | User Manual - Page 76
    be displayed. • If there is no key input for about 5 minutes while the Inquiring Code is displayed, the projector will turn off. 3-2 Contact your dealer with the 10 digit Inquiring Code. Your PIN code will be sent after your user registration information is confirmed. (continued on next page) 76
  • Hitachi CP-X3014WN | User Manual - Page 77
    ENTER button on the remote control or the ► button on the projector will return to the TRANSITION DETECTOR on/off menu. • Please do not forget your TRANSITION DETECTOR password. • This function will activate only when the projector is started after turning off the AC power. • This feature may
  • Hitachi CP-X3014WN | User Manual - Page 78
    for about 30 seconds, then please make note of the password during this time. Pressing the ENTER button on the remote control or ► button on the projector will return to the MY TEXT PASSWORD on/off menu. 2 Turning off the MY TEXT PASSWORD 2-1 Follow the procedure in 1-1 to display the MY TEXT
  • Hitachi CP-X3014WN | User Manual - Page 79
    MY TEXT will be displayed on the START UP screen and the INPUT_ INFORMATION when the INFORMATION on the SERVICE menu is chosen. • This function is available only when the MY TEXT PASSWORD function is set to the OFF. (1) Use the ▲/▼ buttons on the SECURITY menu to select the MY TEXT WRITING
  • Hitachi CP-X3014WN | User Manual - Page 80
    Presentation tools Presentation tools The projector has the following two convenient tools that enable on-screen computer. - Thumbnail mode ( 81) - Full Screen mode ( 85) - Slideshow mode ( 87) [Supported storage media] • USB memory (USB memory type, USB hard disk and USB card reader type) NOTE
  • Hitachi CP-X3014WN | User Manual - Page 81
    NOTE • Files with a resolution larger than the following are not supported. CP-X2514WN, CP-X3014WN,CP-X4014WN: 1024 x 768 (Still)ɼ768 x 576 (Movie) CP-WX3014WN: 1280 x 800 (Still)ɼ768 x 576 (Movie) (* Some computers may not support 1280 x 800.) • Files with a resolution smaller than 36 x 36 are
  • Hitachi CP-X3014WN | User Manual - Page 82
    can control the images on the Thumbnail screen with the remote control, control panel or Web Remote Control. The following functions can be supported while the Thumbnail is displayed. Button operation The remote control Control panel Web Remote Control PAGE UP PAGE DOWN - [PAGE UP
  • Hitachi CP-X3014WN | User Manual - Page 83
    the Slideshow mode. Switches the input port. Displays the menu. Be sure to use this function before removing USB storage device from the projector. After that, the projector will not recognize a USB storage device until you insert it again into the USB TYPE A input port. Turns the sound on/off for
  • Hitachi CP-X3014WN | User Manual - Page 84
    Presentation (continued) NOTE • These operations are not accessible while the projector OSD is displayed. • The Thumbnail mode is able to display the Thumbnail. This file seems to be broken or not supported format. A file that cannot be displayed on the thumbnail screen is indicated by a file format icon.
  • Hitachi CP-X3014WN | User Manual - Page 85
    Presentation tools PC-LESS Presentation (continued) Full Screen Mode The Full Screen mode shows a full display image. To display in Full Screen mode, select an image in the Thumbnail screen. Then press the ENTER button on the remote control, the INPUT button on the control panel or click [ENTER] on
  • Hitachi CP-X3014WN | User Manual - Page 86
    -forward (REW) Fast-rewind (Stop), Displays Thumbnail. Shows the next file. Shows the previous file. NOTE • These operations are not accessible while the projector OSD is displayed. • It is not possible to change the input port by using the INPUT button when the Thumbnail screen, Slideshow, or Full
  • Hitachi CP-X3014WN | User Manual - Page 87
    ENTER Button operation Control panel Web Remote Control INPUT [ENTER] Functions Displays thumbnail NOTE • These operations are not accessible while the projector OSD is displayed. • It is not possible to change the input port by using the INPUT button when the Thumbnail screen, Slideshow
  • Hitachi CP-X3014WN | User Manual - Page 88
    Presentation tools PC-LESS Presentation (continued) You can play the Slideshow at your desired configuration. Configure the Slideshow items in the Thumbnail. 1) RETURN : Returns to the thumbnail mode. 2) PLAY : Play the Slideshow. 3) START : Set the beginning number of the Slideshow. 4) STOP
  • Hitachi CP-X3014WN | User Manual - Page 89
    Presentation tools PC-LESS Presentation (continued) Playlist The Playlist is a DOS format text file, which decides the order of displayed still image files in the Thumbnail or Slideshow. The playlist file name is "playlist.txt" and it can be edited on a computer. It is created in the folder that
  • Hitachi CP-X3014WN | User Manual - Page 90
    projector using a USB cable, the projector will be recognized as a CD-ROM drive on is not drive F on your computer, you will need to replace F with the correct drive letter assigned to your CD-ROM drive software and its manual. ( User's Manual (concise)) Follow the instructions that can be obtained at
  • Hitachi CP-X3014WN | User Manual - Page 91
    (refer to the Network Guide) and this application cannot be used at the same time. If you connect your computer to the projector by using a USB cable your computer, make the firwall function invalid with following the user's manual. • Some security software may block image transmission. Please change
  • Hitachi CP-X3014WN | User Manual - Page 92
    before the button is clicked is remained on the screen. You can revise the image data on your computer without showing it on the projector's screen. r Option button The Options window is displayed. t Minimize button The Floating menu is closed, and the icon reappears in the Windows notification
  • Hitachi CP-X3014WN | User Manual - Page 93
    over Speed. It makes JPEG compression rate lower. The screen on the projector is rewritten slower because the transferred data is larger, but the image may be faster. CP-X2514WN, CP-X3014WN, CP-X4014WN: 1024 x 768 (XGA) CP-WX3014WN: 1280 x 800 If your computer does not support the display resolution
  • Hitachi CP-X3014WN | User Manual - Page 94
    after you start using them. Preparation of a new lamp and early replacement are recommended. To prepare a new lamp, make contact with your dealer and tell the lamp type number. Type number : DT01021 Replacing the lamp lamp cover 3 1. Turn the projector off, and unplug the power cord. Allow the
  • Hitachi CP-X3014WN | User Manual - Page 95
    In addition, working in high places is dangerous, so ask your local dealer to have the lamp replaced even if the bulb is not broken. • Do not use the projector with the lamp cover removed. At the lamp replacing, make sure that the screws are screwed in firmly. Loose screws could result in damage or
  • Hitachi CP-X3014WN | User Manual - Page 96
    type will come together with a replacement lamp for this projector. 1. Turn the projector off, and unplug the power cord. Allow the projector to sufficiently cool down. Filter cover 2 2. Use a vacuum cleaner on and around the filter cover. 3. While supporting the projector with one hand, use your
  • Hitachi CP-X3014WN | User Manual - Page 97
    or the like, internal temperatures rise and could cause a fire, a burn or malfunction to the projector. NOTE • Please replace the air filter when it is damaged or heavily soiled. • When you replace the projection lamp, please replace the air filter. An air filter of specified type will come together with
  • Hitachi CP-X3014WN | User Manual - Page 98
    . CAUTION ►Please take right care of the projector according to the following. Incorrect care could cause not only an injury but adverse influence such as discoloration, peeling paint, etc. ►Do not use cleaners or chemicals other than those specified in this manual. ►Do not polish or wipe with hard
  • Hitachi CP-X3014WN | User Manual - Page 99
    Troubleshooting Troubleshooting If an abnormal operation should occur, stop using the projector contact to your dealer or service company. Otherwise if a problem occurs with the projector, the following checks and specs for your projector or the signal source specs. An improper signal is input. Please
  • Hitachi CP-X3014WN | User Manual - Page 100
    it may cause damage to the projector itself or the parts inside. A note of precaution when cleaning the air filter. Please immediately turn the power off, and clean or change the air filter referring to the Cleaning and replacing the air filter section of this manual. After you have cleaned or changed
  • Hitachi CP-X3014WN | User Manual - Page 101
    is displayed after the remedy, please change the lamp referring to the section Replacing the lamp. Blinking In Red or Lighting In Red Blinking In Red Turned off The lamp cover has not been properly fixed. Please turn the power off, and allow the projector to cool down at least 45 minutes. After
  • Hitachi CP-X3014WN | User Manual - Page 102
    Troubleshooting Regarding the indicator lamps (continued) POWER LAMP TEMP indicator indicator indicator Description state of the lamp and lamp cover, and then turn the power on again. If the projector is used at an altitude of about 1600 m or higher, set FAN SPEED of the SERVICE item in the
  • Hitachi CP-X3014WN | User Manual - Page 103
    Troubleshooting Resetting all settings When it is hard to correct some wrong settings, the FACTORY RESET function of SERVICE item in OPTION menu ( 62) can reset all settings (except settings such as LANGUAGE, LAMP TIME, FILTER TIME, FILTER MESSAGE, SECURITY and NETWORK) to the factory default. Be
  • Hitachi CP-X3014WN | User Manual - Page 104
    Troubleshooting Phenomena that may be easy to be mistaken for machine defects (continued level. Adjust BRIGHTNESS to a higher level using the menu 32 function. The computer cannot detect the projector as a plug No pictures are and play monitor. displayed. Make sure that the computer can detect
  • Hitachi CP-X3014WN | User Manual - Page 105
    level using the menu function. Pictures The projector is operating in Eco mode. appear dark. Set ECO MODE to NORMAL, and set AUTO ECO 43 MODE to OFF, in the SETUP menu. The lamp is approaching the end of its product lifetime. Replace the lamp. 94 ~ 95 Pictures appear blurry. Either the
  • Hitachi CP-X3014WN | User Manual - Page 106
    Troubleshooting Phenomena that may be easy to be mistaken for machine defects (continued) Phenomenon Cases not involving a machine defect Reference page When the projector is connected to the projector while the USB wireless adapter is connected to the projector, noise from the adapter
  • Hitachi CP-X3014WN | User Manual - Page 107
    Select NETWORK BRIDGE for COMMUNICATION TYPE item in the OPTION - SERVICE - COMMUNICATION 59 menu. The SAVING function is working. Select AND TIME setting for WIRELESS SETUP or WIRED SETUP in the NETWORK menu. 65, 69 Disconnect the LAN cable and check that the projector is working properly.
  • Hitachi CP-X3014WN | User Manual - Page 108
    Specifications Specifications Please see the Specifications in the User's Manual (concise) which is a book. End User License Agreement for the Projector Software • Software in the projector consists of the plural number of independent software modules and there exist our copyright or/and third party
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
1
Projector
CP-X2514WN/CP-X3014WN/
CP-X4014WN/CP-WX3014WN
User's Manual (detailed)
Operating Guide
Thank you for purchasing this projector.
►Before using this product, please read all manuals for this
product. Be sure to read
Safety Guide
first. After reading them, store them in a
safe place for future reference.
WARNING
• The information in this manual is subject to change without notice.
• The manufacturer assumes no responsibility for any errors that may appear in
this manual.
• The reproduction, transfer or copy of all or any part of this document is not
permitted without express written consent.
NOTE
Trademark acknowledgment
Various symbols are used in this manual. The meanings of these symbols are
described below.
About this manual
WARNING
CAUTION
This symbol indicates information that, if ignored, could possibly
result in personal injury or even death due to incorrect handling.
This symbol indicates information that, if ignored, could possibly
result in personal injury or physical damage due to incorrect
handling.
Please refer to the pages written following this symbol.
±
•
Mac
®
is a registered trademark of Apple Inc.
•
Windows
®
, DirectDraw
®
and Direct3D
®
are registered trademarks of Microsoft Corporation
in the U.S. and/or other countries.
•
VESA and DDC are trademarks of the Video Electronics Standard Association.
•
HDMI, the HDMI logo, and High-Definition Multimedia Interface are trademarks or registered
trademarks of HDMI Licensing LLC in the United States and other countries.
•
Trademark PJLink is a trademark applied for trademark rights
in Japan, the United States of America and other countries and
areas.
• Blu-ray Disc
TM
is a trademark.
All other trademarks are the properties of their respective owners.
NOTICE
This entry notices of fear of causing trouble.