Hitachi CP-X4021N Instant Stack Guide
Hitachi CP-X4021N Manual
 |
View all Hitachi CP-X4021N manuals
Add to My Manuals
Save this manual to your list of manuals |
Hitachi CP-X4021N manual content summary:
- Hitachi CP-X4021N | Instant Stack Guide - Page 1
Projector CP-X4021N/CP-X5021N CP-WX4021N User's Manual (detailed) Instant Stack Guide Thank you for purchasing this product. This manual is intended to explain only Instant Stack feature. Other than what is mentioned in this manual, please see other manuals of this product. Features This projector - Hitachi CP-X4021N | Instant Stack Guide - Page 2
Main projector 30 5.4 Setting on menu 31 Inputting image to Sub from Main - Computer signal 31 Inputting image to Sub from Main - Video signal (either COMPONENT or VIDEO).... 32 Inputting image of Sub and Main individually 31 6. Restriction on Schedule function.........34 7. Troubleshooting 36 - Hitachi CP-X4021N | Instant Stack Guide - Page 3
entry notices of fear of causing trouble. 1.2 Important safety instruction The followings are important instructions for safely using the product in the projectors on a ceiling. • Do not touch the stacked projectors except when instructions are given in this manual. Do not hit the projectors with - Hitachi CP-X4021N | Instant Stack Guide - Page 4
1.2 Important safety instruction - For Instant Stack feature (continued) Introduction WARNING ► projectors, use LAN connection that can be connected with one of the projectors. • When you use Intellectual Stack, the operations or setting of some functions are restricted. Refer to this manual for - Hitachi CP-X4021N | Instant Stack Guide - Page 5
manufacturer. Read and keep the manuals of the accessories used. • For special installation such as ceiling mounting, be sure to consult your dealer beforehand. Specific mounting accessories and services may be required. ► Do not install the projector near thermally conductive or flammable things - Hitachi CP-X4021N | Instant Stack Guide - Page 6
should disable the remote control by KEY LOCK. (Operating Guide → OPTION menu) Installation styles There are following two styles to install two projectors. Instant Stack can support both of them. Style 1 : Piling them up vertically Style 2 : Lining them up horizontally This manual is mainly - Hitachi CP-X4021N | Instant Stack Guide - Page 7
control and to operate the other by the control panel on the projector or wired remote. In this case the other projector should disable the remote control by KEY LOCK. (Operating Guide → OPTION menu) ● Even if the images of Set A and Set B are fully superimposed once, it may shift over time. Adjust - Hitachi CP-X4021N | Instant Stack Guide - Page 8
set over the other may slide down. Deciding installation position Decide the position of Set A and its projection angle. (User's Manual (concise) → Arrangement and Adjusting the projector's elevator.) NOTE • The angle of gradient of Set A to the horizontal line should be within 12 degrees. • Keep - Hitachi CP-X4021N | Instant Stack Guide - Page 9
. (User's Manual (concise) → Displaying the picture) If necessary, also use KEYSTONE and PERFECT FIT to set the image position. (Operating Guide → , go to Installation of the second projector (Set B). (11) 4. Display a menu with MENU button. (Operating Guide → Using the menu function) 5. Using - Hitachi CP-X4021N | Instant Stack Guide - Page 10
Installation of the first projector (Set A) - Setting up Set A (continued) Installation 6. Use the the ► button to complete the setting. (23) 8. Disable the remote control by KEY LOCK if you use Intellectual Stack. (Operating Guide → OPTION menu) NOTE • During the installation, Set A will not - Hitachi CP-X4021N | Instant Stack Guide - Page 11
Make sure that the feet are reached to the bottom of the stack pockets on Set A. CAUTION ►Be careful that when you pile up two projectors, a projector set over the other may slide down. 3. Make the feet of Set B rotate two revolutions counterclockwise to keep about 1 mm space between a protrusion at - Hitachi CP-X4021N | Instant Stack Guide - Page 12
the remote control. (Operating Guide → OPTION menu) • If you use Simple Stack, go to For Simple Stack users. (16) 4. Display a menu with MENU button. (Operating Guide → Using the menu function) 5. Using the buttons, go down the menu tree as below. ADVANCED MENU > OPTION > SERVICE > COMMUNICATION - Hitachi CP-X4021N | Instant Stack Guide - Page 13
the second projector (Set B) - Setting up Set B (continued) 6. Use the ▲/▼ buttons to point at STACK MODE, and press the ► button to display STACK MODE dialog. Point at MAIN with the ▲/▼ buttons, and press the ◄ button to return to the previous menu. 7. Use the ▲/▼ buttons to point at LAMP MODE, and - Hitachi CP-X4021N | Instant Stack Guide - Page 14
2.4 Confirmation of Main & Sub setting 1. Press MENU button on the remote control to Main (Set B). NOTE • In use of Intellectual Stack, the remote control signal can be received by the Main only, and the Sub ignores the remote control signal. 2. The MENU dialogs appear on the lower right of screen - Hitachi CP-X4021N | Instant Stack Guide - Page 15
B) is finely adjusted with PERFECT FIT. For Intellectual Stack users 1. Press MENU button on the remote control or control panel on Main (Set B) to display (Set B) to fully superimpose to the image of Sub (Set A). (Operating Guide → EASY MENU or OP- TION menu) It is recommended to adjust it by - Hitachi CP-X4021N | Instant Stack Guide - Page 16
the following measures. - Press AUTO button of the remote control or execute AUTO ADJUST EXECUTE (Operating Guide → IMAGE menu) on each of the projectors. - Adjust H POSITION and V POSITION (Operating Guide → IMAGE menu) on each of the projectors. - Check RESOLUTION setting on INPUT menu, and if - Hitachi CP-X4021N | Instant Stack Guide - Page 17
this chapter, jump to 3.3 Selecting lamp working mode. (19) • Read carefully projectors. Otherwise, STACK menu on the projectors cannot be operated. (7) - STANDBY MODE in SETUP menu: NORMAL (Operating Guide → SETUP menu) - COMMUNICATION TYPE in COMMUNICATION in SERVICE menu: OFF (Operating Guide - Hitachi CP-X4021N | Instant Stack Guide - Page 18
. (23) NOTE • After setting Main or Sub, the setting information can be monitored on Web Control. (Network Guide → Web Control) Select Projector Status on the main menu of web control. Stack Mode item shows whether your projector is set to Main or Sub, even though STACK MODE is set to OFF. 18 - Hitachi CP-X4021N | Instant Stack Guide - Page 19
► button to com- plete the setting. (23) NOTE • If DUAL is selected for the LAMP MODE, a menu to select MAIN or SUB may be displayed on screen first when a button on the control panel of the projector or remote control is pressed. If displayed, select one of them which you want to operate - Hitachi CP-X4021N | Instant Stack Guide - Page 20
operates in different way from normal use. (Operating Guide → Troubleshooting) When Main and Sub projectors are in standby mode, if STANDBY/ON button on the remote control or control panel of Main projector is pressed, Main projector will decide projectors to turn on in accordance with STACK MODE - Hitachi CP-X4021N | Instant Stack Guide - Page 21
the ▲/▼ buttons in the dialog to point at AUTO or NORMAL. AUTO : for turning on one projector that has the lamp which usage time is shorter than the other's one. NORMAL : for turning on one projector that was not used last time. 3. Press the ◄ button to turn back to previous menu, or the - Hitachi CP-X4021N | Instant Stack Guide - Page 22
IN 1) is selected, either COMPUTER IN 1 or IN 2 port can be selected as an input source on Main projector. When COMPUTER or VIDEO button on the remote control or INPUT button on the projector is pressed, MAIN INPUT SOURCE dialog will be displayed on screen. Select COMPUTER IN 1 or IN 2 with the - Hitachi CP-X4021N | Instant Stack Guide - Page 23
wait for a while. ● Pressing the ◄ button (as NO) in the dialog returns to the COMMUNICATION menu without saving the setting. (Operating Guide → OPTION menu → SERVICE) In a dialog from the STACK menu When you press the ► button (as EXIT) with any setting change, the confirmation dialog will appear - Hitachi CP-X4021N | Instant Stack Guide - Page 24
network communication to Sub and by Web control on Sub. Sub projector should be controlled though Main projector. ● Remote Control function on Web Control of Sub projector is disabled. (Network Guide → 3.11 Remote Control) ● If the projectors are tried to turn on with using Power on & Display on - Hitachi CP-X4021N | Instant Stack Guide - Page 25
has a problem. Temp Error: Temperature in projector is too high. Air Flow Error: Check exhaust vent that may be blocked, since temperature in projectore is too high. Filter Error: Filter timer counts hours more than the setting hours on Filter Message menu. (Operating Guide → OPTION menu → SERVICE - Hitachi CP-X4021N | Instant Stack Guide - Page 26
Input security code for Main first and Sub next. If ALTERNATE mode is selected, one of the projectors will be turned off automatically. (Operating Guide → SECURITY menu) ● If SECURITY function on one of projectors are set to on, it is required to input security code as below, when turning on. - In - Hitachi CP-X4021N | Instant Stack Guide - Page 27
So, be aware that Main read as a projector and Sub does as the other in this chapter. • For detail of input port, specs, connections and so on, refer to Connecting with your devices (← Operating Guide) and Connection to the ports (← Operating Guide - Technical) 4.1 Connecting RS-232C cable If you - Hitachi CP-X4021N | Instant Stack Guide - Page 28
, input it to COMPUTER IN1 and IN2. Main - If you wish to input a video signal, input it to Y pin of component signal on COMPUTER IN1 and IN2. NOTE for Simple Stack • As an input port on the projector that is connected a computer cable to the ports MONITOR OUT, COMPUTER IN1 and IN2 - Hitachi CP-X4021N | Instant Stack Guide - Page 29
input port that you connect the cables to, pressing COMPUTER or VIDEO button on the remote control or INPUT button on the control panel on both projectors. For setting of the MONITOR OUT, refer to SETUP menu in the Operating Guide. Then, the setting is finished. If you use Intellectual Stack with - Hitachi CP-X4021N | Instant Stack Guide - Page 30
, this section shows you how you can switch from Sub projector to Main. 1. Using the buttons, go down the menu tree as below. ADVANCED MENU > OPTION > SERVICE > COMMUNICATION > STACK STACK menu will appear on screen. (Operating Guide → OPTION menu) 2. Check ALTERNATE MODE setting in the menu. If - Hitachi CP-X4021N | Instant Stack Guide - Page 31
as below. ADVANCED MENU > OPTION > SERVICE > COMMUNICATION > STACK STACK menu will appear on screen. (Operating Guide → OPTION menu) 3. Use the (23) 5. Press COMPUTER or VIDEO button on the remote control or INPUT button on the control panel on Main projector, MAIN INPUT SOURCE dialog is displayed - Hitachi CP-X4021N | Instant Stack Guide - Page 32
Press MENU button on the remote control or control panel on Main projector. Then, using the buttons, open COMPUTER IN dialog. (Operating Guide → INPUT menu) 3. If you input video signal on either COMPUTER IN 1 or IN 2 port, set VIDEO at the port. If it is necessary to select a video format, use - Hitachi CP-X4021N | Instant Stack Guide - Page 33
point at FOLLOW MAIN UNIT, and press the ► button to complete the setting. (23) 5. Press COMPUTER or VIDEO button on the remote control or INPUT button on the control panel on Main projector, MAIN INPUT SOURCE dialog is displayed on screen. Use the ▲/▼ buttons to point at the source you connected - Hitachi CP-X4021N | Instant Stack Guide - Page 34
on Schedule function This model supports schedule function on Web Control feature. (Network Guide → 3. Web Control LAMP MODE ALTERNATE ON OFF 1) X *3) OFF ON *1) X *2) X *2) X *3) DUAL/ ALTERNATE OFF OFF *1) X *2) X *2) X *3) Restriction on Sub projector Functions Projector - Hitachi CP-X4021N | Instant Stack Guide - Page 35
Stack or by STANDBY/ON button on the remote control or control panel of Main projector, and is in standby mode. • The projectors cannot be turned on by the schedule function on Sub projector. Set it on Main projector if necessary. • When Sub projector is turned off in ALTERNATE mode, the schedule - Hitachi CP-X4021N | Instant Stack Guide - Page 36
Troubleshooting Stack feature, supply Main in User's and Sub projectors with AC power. If one Manual of the projector is not supplied, Intellectual (concise are matched. Guide Main and Sub do not work collaboratively. RS-232C cable is not connected to Main and Sub projector correctly. Connect - Hitachi CP-X4021N | Instant Stack Guide - Page 37
COMMUNICATION TYPE in COMMUNICATION in SERVICE menu: OFF - STACK LOCK in SECURITY menu: OFF The remote control points at Sub projector. When the projector is working on Intellectual Stack, only Main projector can receive the 6 remote control signal. So, point at Main projector when you use the
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
 |
 |
1
Projector
CP-X4021N/CP-X5021N
CP-WX4021N
User's Manual (detailed)
Instant Stack Guide
Thank you for purchasing this product.
This manual is intended to explain only
Instant Stack
feature. Other than what is
mentioned in this manual, please see other manuals of this product.
WARNING
►Before using this product, be sure to read all manuals for this
product.
After reading them, store them in a safe place for future reference.
►Follow all the instructions in the manuals or on the product.
The manufacturer
assumes no responsibility for any damage caused by mishandling that is beyond
normal usage defined in the manuals.
NOTE
• The information in this manual is subject to change without notice.
• The manufacturer assumes no responsibility for any errors that may appear in
this manual.
• The reproduction, transfer or copy of all or any part of this document is not
permitted without express written consent.
Trademark acknowledgment
All the trademarks in this manual are the properties of their respective owners
.
Features
This projector can be used with one more same type projector to make one image
on one screen with
Instant Stack
feature.
The two projectors can work simultaneously to make the image brighter.
Moreover, if you connect two projectors with RS-232C cross-over cable, it turns to
a kind of intellectual stacking system.
The two projectors can work alternately by
themselves, and once one projector has an accident the other voluntarily starts to
work to keep your presentation going.
These features, generically called
Instant Stack
, provide you with the broad use.