Hitachi c10fs Handling Instructions
Hitachi c10fs - 940543 3/8 Box Wrench Manual
 |
View all Hitachi c10fs manuals
Add to My Manuals
Save this manual to your list of manuals |
Hitachi c10fs manual content summary:
- Hitachi c10fs | Handling Instructions - Page 1
Slide Compound Miter Saw Model C 10FSH (Laser Marker Equipment) C 10FSB Handling instructions NOTE: Before using this Power Tool, carefully read through these HANDLING INSTRUCTIONS to ensure efficient, safe operation. It is recommended that these INSTRUCTIONS be kept readily available as an - Hitachi c10fs | Handling Instructions - Page 2
for better and safer performance. Follow instructions for lubricating and changing accessories. Inspect tool cords periodically and if damaged have them repaired by an authorized service facility. Inspect extension cords periodically and replace if damaged. Keep handles dry, clean and free from oil - Hitachi c10fs | Handling Instructions - Page 3
be properly repaired or replaced by an authorized service center unless otherwise indicated in this handling instructions. Have defective switches replaced by an authorized service center. Do not use the tool if the switch does not turn it on and off. 21. Do not use power tools for applications - Hitachi c10fs | Handling Instructions - Page 4
PRECAUTION ON USING SLIDE COMPOUND MITER SAW 1. Review this Manual and familiarize yourself with the safety rules and operating instructions for this POWER TOOL before attempting to use it. 2. Always confirm that the POWER TOOL is clean before using it. 3. Always wear snug-fitting clothing, non-skid - Hitachi c10fs | Handling Instructions - Page 5
OF PARTS Dust Bag Hinge Holder (A) Sub Cover Indicator (For right bevel scale) Laser Marker (Only C10FSH) Saw Blade Motor Lever (A) Gear Case Head Handle Motor Spindle Cover (Only Model 240V) Washer (D) Lower Guard Rotation Direction Fence (A) Indicator (For miter scale) Vise Assembly Fence - Hitachi c10fs | Handling Instructions - Page 6
Wave length Laser medium Miter Bevel Compound Miter sawing range Bevel sawing range Compound sawing range Net weight Cord 6 C10FSH / C10FSB Series commutator motor Single-phase AC 50Hz (230V, 240V) 1450W - Hitachi c10fs | Handling Instructions - Page 7
20 (Fig. 28). STANDARD ACCESSORIES 1 262mm (10") TCT Saw blade (1 piece) 2 Dust bag (1 piece) 4 10mm BOX wrench (1 piece) 3 Vise Assembly w/knob bolt (1 piece) 5 Collar Outside Dia. 25.4mm (1") (1 piece) Outside Dia. 30mm (1-3/16") (1 piece) (Only model 240V) For how to use, refer to page 18 - Hitachi c10fs | Handling Instructions - Page 8
the thickness of the work bench. For example, use 65mm (2-9/16" ) or larger bolts for a 25mm (1") thick work bench. The holder attached to the rear of the base helps stabilize the power tool. Holder adjustment: Loosen the 6mm bolt with the supplied 10mm box wrench. Adjust the holder until its - Hitachi c10fs | Handling Instructions - Page 9
(The holder and stopper are optional accessories.) Attach the dust bag and vise assembly as indicated in Fig. 1 and Fig. 2. BEFORE USING 1. Make sure the power source is appropriate for the tool. WARNING: Never connect the power tool unless the available AC power source is of the same voltage as - Hitachi c10fs | Handling Instructions - Page 10
if it is faulty. 9. Confirm the tool's power cord is not damaged. Repair or replace the power cord if an inspection indicates that it is damaged. AFTER CONNECTING THE POWER PLUG TO AN APPROPRIATE AC POWER SOURCE, CHECK THE OPERATION OF THE TOOL AS FOLLOWS: 10. Trial Run After confirming that no one - Hitachi c10fs | Handling Instructions - Page 11
fence and the table surfaces, fix it with Workpiece the vise assembly. Fence (A) After the switch has been turned on and the saw blade has reached maximum speed, slowly lower the handle gap between the side surface of the table insert and the saw blade will be minimum. Before using the tool, - Hitachi c10fs | Handling Instructions - Page 12
you replace a saw blade with a new one, adjust the lower limit position so that the saw blade will not cut the turntable or complete cutting cannot be done. To adjust the lower limit position of the saw blade, follow the procedures (1) to (4) indicated below. Saw Blade (Fig. 10-b) Furthermore - Hitachi c10fs | Handling Instructions - Page 13
motor head and the top of the workpiece at the saw blade's lower limit position (where the head of the 8mm depth adjustment bolt contacts the gear case. (3) After adjustment, turn the 8mm wing nut until it contacts the Hinge (see Fig. 10-b), and fully tighten it. 5. Confirmation for use of sub fence - Hitachi c10fs | Handling Instructions - Page 14
6mm Knob Bolt (Optional accessory) and in place during the cutting operation. (1) As indicated in Fig. 13, use a steel square for aligning the upper edge of the holders with the base surface. Steel Square Loosen the 6mm wing nut. Turn a height adjustment bolt 6mm, and adjust the height of the - Hitachi c10fs | Handling Instructions - Page 15
blade or some part of the tool, causing in serious injury to operator. Sub Fence (A) Fig. 15 In the case of direct angle cutting and angle cutting, use the sub fence (A). The sub fence (A) can be installed on the right side of the guide fence. Insert the rods of the sub fence (A) into the holes - Hitachi c10fs | Handling Instructions - Page 16
in handling a switch trigger for the position adjustment of the laser line, as the power plug is plugged into the receptacle during operation. If the switch trigger is pulled inadvertently, the saw blade can rotate and result in unexpected accidents. * Do not remove the laser marker to be used for - Hitachi c10fs | Handling Instructions - Page 17
) or the ink line on the right side. The laser line is adjusted to the width of the saw blade at the time of factory shipment. Adjust the positions of the saw blade and the laser line taking the following steps to suit the use of your choice. (1) Light up the laser marker and make a groove of about - Hitachi c10fs | Handling Instructions - Page 18
the tool is turned on when the switch trigger is pulled and off when the trigger switch is released. 2. Using the Vise Assembly (Standard accessory) Screw Holder The vise assembly can be mounted on either the left fence (Fence (B)) or the right fence (Fence (A)), 6mm Knob Bolt Knob and can be - Hitachi c10fs | Handling Instructions - Page 19
motor head. For other compound cutting (left bevel + right miter, right bevel + left miter and right bevel + right miter), mount the vise assembly on the opposite side of the inclination of the motor head to avoid the contact of the vise assembly with the motor head. 3. Cutting Operation Adjusting - Hitachi c10fs | Handling Instructions - Page 20
10 minutes or so, and then restart your cutting operation. 4. Cutting narrow workpieces (Press cutting) Hinge Handle Slide the hinge down to holder (A), then tighten the slide securing knob (see Fig. 2) as indicated in Press Down Fig. 27. Lower the handle to cut the workpiece. Using the power - Hitachi c10fs | Handling Instructions - Page 21
operation in order to reduce the risk of injury. * Never put your hand on the side handle during the cutting operation because the saw blade comes close to the side handle when the motor head is lowered. 7. Bevel cutting procedures Fixing pin Holder (A) (1) Loosen the clamp lever and bevel - Hitachi c10fs | Handling Instructions - Page 22
properly aligned. * Operation of the saw with the miter scale and indicator out of alignment, or with the side handle not properly tightened, will result in poor cutting precision. 9. Compound cutting procedures Compound cutting can be performed by following the instructions in 7 and 8 above. For - Hitachi c10fs | Handling Instructions - Page 23
of the angles described, move the turntable adjusting side handle a little to the right and left to stabilize the position and to properly align the miter angle scale and the tip of the indicator before the operation starts. For bevel cut setting Move handle on bevel section to the left and check - Hitachi c10fs | Handling Instructions - Page 24
crown moldings: 33.9° ( mark) 3 Position the crown molding so that the lower surface (B in Fig. 34) contacts the fence as in Fig. 40. Head Bevel Angle Scale 2 1 4 Fence Fence Head Bevel Angle Scale 3 Miter Angle Scale Base Turntable Miter Angle Scale Base Turntable Fig. 37 24 Fig. 38 - Hitachi c10fs | Handling Instructions - Page 25
Fig. 34) contacts the fence as indicated Fig. 43. (4) Setting fence as in Fig. 44. Head 4 Bevel Angle Scale 1 Fence Head 3 Fence Bevel Angle Scale 2 Miter Angle Scale Base Turntable Fig.41 Turntable Base Miter Angle Scale Fig. 42 Fence B A Table on Base Fig. 43 Fence A B Table on Base - Hitachi c10fs | Handling Instructions - Page 26
cuts of crown molding without tilting the saw blade. Install them in the base both-sides side to be shown in Fig. 45-a. After inserting Tighten the 6mm 6mm Knob Bolt Knob Bolt knob bolts to secure the crown molding Stoppers. [Optional accessories used] • Crown molding Vise Ass'y (Include Crown - Hitachi c10fs | Handling Instructions - Page 27
of blade 4 Right 45° Save the left side of blade Use the sub fence (A) (optional accessories) to secure the crown molding more firmly. (see Fig. 15) 11. Groove cutting procedures 8mm Wing Nut Cut grooves with saw blade 8mm Depth a Adjustment Bolt b Gear Case b Fig. 46 Bottom Line of - Hitachi c10fs | Handling Instructions - Page 28
Vise Assembly Clamp Fence Wood Plate Fence Aluminum Sash 6mm Knob Bolt Wood Plate Fig. 48-a Wood Plate Wood Plate Aluminum Sash Fig. 48-b 13. How to use the dust bag (Standard accessory) (1) When the dust bag has become full of sawdust, Dust Bag dust will be blown out of the dust bag when - Hitachi c10fs | Handling Instructions - Page 29
trigger switch and disconnect the power plug from the receptacle before removing or installing a saw blade. If cutting work is saw blade (Fig. 50-a, Fig. 50-b and Fig. 50-c) (1) Use the accessory 10mm box wrench to loosen the 6mm bolt fastening the spindle cover and then remove the spindle cover - Hitachi c10fs | Handling Instructions - Page 30
to the left by standard accessorie's wrench (10mm box wrench) as indicated in Fig. 50-c. CAUTION:* A dust guide is installed inside behind the gear case. When removing or installing the saw blade, do not make contact with the dust guide. Contact may break or chip saw blade tips. * Confirm that the - Hitachi c10fs | Handling Instructions - Page 31
these adjustment. 3. Inspecting the carbon brushes For your continued safety and electrical shock protection, carbon brush inspection and replacement on this tool should ONLY be performed by a Hitachi Authorized Service Center. 4. About Handling the Motor (see Fig. 1) Winding of the motor is - Hitachi c10fs | Handling Instructions - Page 32
. Fig. 54 10. Lubrication Lubricate the following sliding surfaces once a month to keep the power tool in good operating condition for a long time (see Fig. 1 and Fig. 2). Use of machine oil is recommended. Oil supply points: * Rotary portion of hinge * Rotary portion of vise assembly * Rotary - Hitachi c10fs | Handling Instructions - Page 33
require servicing or replacement of parts because of wear from normal use. To assure that only authorized replacement parts will be used and that the double insulation system will be protected, all service (other than routine maintenance) must be performed by an AUTHORIZED HITACHI POWER TOOL REPAIR - Hitachi c10fs | Handling Instructions - Page 34
C10FSH 8 9 10 11 12 1 23 4 7 26 40 41 27 28 29 30 29 14 15 31 16 13 17 18 32 33 46 9 19 10 20 35 34 10 10 9 22 65 21 36 66 37 23 38 39 24 25 601 603 602 618 604 605 602 606 607 10 608 9 42 43 9 10 44 45 47 - Hitachi c10fs | Handling Instructions - Page 35
C10FSH 35 - Hitachi c10fs | Handling Instructions - Page 36
C10FSH 141 142 143 144 143 145 146 153 154 155 156 157 158 159 160 154 222 223 224 231 224 149 148 147 143 - Hitachi c10fs | Handling Instructions - Page 37
C10FSH A B 1 305-180 2 305-179 3 312-488 4 329-409 7 965-077 8 321-330 9 949-429 10 × 8 1 2 M8 × 25 1 "14-20" 1 M10 1 M6 × 12 1 1 1 1 M5 × 12 1 1 M6 × 17 4 M8 × 35 1 1 M6 × 10 1 1 9, 10, 27-34, 40, 41, 43, 44, 47-52, 54 1 1 2 M12 1 1 1 1 3 1 M6 1 1 1 "37" 1 M6 × 25 2 6 M6 × 16 1 1 1 - Hitachi c10fs | Handling Instructions - Page 38
C10FSH A 151 1 151 2 152 153 154 155 156 157 158 159 160 321-551 1 M10 × 54 604 998-836 1 M6 × 11 605 -------- 1 606 306-985 1 607 964-851 1 608 304-043 1 M4 × 10 609 960-017 1 M6 × 32 610 987-860 2 M6 × 6 611 321-552 2 612 -------- 1 613 321-387 1 "609-612" 614 960 - Hitachi c10fs | Handling Instructions - Page 39
C10FSB 8 9 10 11 12 1 23 4 7 26 40 41 27 28 29 30 29 14 15 31 16 13 32 17 33 18 9 19 10 20 35 34 10 10 22 9 64 21 36 65 37 38 23 39 24 25 601 603 602 618 604 605 602 606 607 10 608 9 42 43 9 10 44 45 46 47 - Hitachi c10fs | Handling Instructions - Page 40
C10FSB 40 - Hitachi c10fs | Handling Instructions - Page 41
C10FSB 121 122 123 129 130 131 132 133 134 135 130 199 200 201 208 201 123 128 127 126 125 124 139 138 137 - Hitachi c10fs | Handling Instructions - Page 42
C10FSB A B 1 305-180 2 305-179 3 312-488 4 329-409 7 965-077 8 321-330 9 949-429 10 8 1 2 M8 × 25 1 "14-20" 1 M10 1 M6 × 12 1 1 1 1 M5 × 12 1 1 M6 × 17 4 M8 × 35 1 1 M6 × 10 1 1 9, 10, 27-34, 40, 41, 43, 44, 46-51, 53 1 1 2 M12 1 1 1 1 3 1 M6 1 1 1 "37" 1 M6 × 25 2 6 M6 × 16 1 1 1 1 - Hitachi c10fs | Handling Instructions - Page 43
C10FSB A 149 2 150 151 152 1 152 2 153 154 155 156 157 158 159 160 161 "602, 618" 1 "603-608" 1 M10 × 54 1 M6 × 11 1 1 A B C D 607 964-851 1 608 304-043 1 M4 × 10 609 960-017 1 M6 × 32 610 987-860 2 M6 × 6 611 321-552 2 612 -------- 1 613 321-387 1 "609-612" 614 960-017 1 - Hitachi c10fs | Handling Instructions - Page 44
Hitachi Koki Co., Ltd. 005 Code No. C99115015 F Printed in China
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
 |
 |
Slide Compound Miter Saw
Model C 10FSH
(Laser Marker Equipment)
C 10FSB
Handling instructions
NOTE:
Before using this Power Tool, carefully read through these
HANDLING INSTRUCTIONS to ensure efficient, safe operation. It is
recommended that these INSTRUCTIONS be kept readily available
as an important reference when using this power tool.