Honeywell 191108AC Owner's Manual

Honeywell 191108AC Manual

Get Honeywell 191108AC PDF manuals and user guides View all Honeywell 191108AC manuals
Add to My Manuals
Save this manual to your list of manuals

Honeywell 191108AC manual content summary:

  • Honeywell 191108AC | Owner's Manual - Page 1
    T8095A/191108AJ; TS8095A/191108AC; T8095A/Q682 Heating-only Thermostat and Wallplate or Heating/Cooling Thermostat and Subbase OWNER'S MANUAL D.F. • Rev. 10-94 • • ©Honeywell Inc. 1994 • Form Number 69-0639-1 M3375
  • Honeywell 191108AC | Owner's Manual - Page 2
    Welcome to the world of energy savings with your new Honeywell thermostat. The Honeywell name is your assurance of accurate control and reliable operation for years to come. Your new thermostat will automatically lower and raise the temperature in your home one or more times every 24 hours. This
  • Honeywell 191108AC | Owner's Manual - Page 3
    Table of Contents Page Features of Your Thermostat ...4 Setting the Temperature ...7 Setting Subbase Switches ...8 Inserting Clock Batteries ...9 Setting the Clock ...10 Programming ...11 Troubleshooting ...15 Servicing the Thermostat ...23 Cycle Rate Adjustment ...23 Thermometer Adjustment ...24
  • Honeywell 191108AC | Owner's Manual - Page 4
    to set clock for energy savings and normal temperature periods. 2 THERMOSTAT COVER. Lift up and remove to adjust heat anticipator. 3 high) temperature setting in control on program index wheel. Also indicates time on 24-hour dial. 8 PROGRAM INDEX WHEEL. Controls high and low temperature
  • Honeywell 191108AC | Owner's Manual - Page 5
    24-hour clock dial slots to control program index wheel. 11 PIN SLOTS. Located on 24-hour dial at 10-minute intervals for program pin insertion. 12 PROGRAM DIAL. 24-hour dial with light band to indicate daytime and dark band to indicate nighttime. 13 MANUAL PROGRAM ADVANCE BUTTON. Allows change from
  • Honeywell 191108AC | Owner's Manual - Page 6
    wiring connections for heating- only or cooling-only thermostat. 18 Q682 SUBBASE (not included with thermostat; ordered separately). Provides mounting base, wiring connections and manual switching control for heating/cooling 17 thermostat. See Setting Subbase Switches section for additional
  • Honeywell 191108AC | Owner's Manual - Page 7
    Setting the Temperature (Fig. 1) For Heating: ■ Set the left lever (blue mark) to the energy savings temperature you want when you are sleeping or your home is unoccupied. ■ Set the right lever (red mark) to the temperature you want for normal comfort periods. NOTE: You may override the time
  • Honeywell 191108AC | Owner's Manual - Page 8
    by the plenum fan switch. In electric heat, heat pump and fan coil systems, the fan is controlled by the thermostat in heating and cooling. To switch positions, use thumb or index finger to slide lever to desired position. Switch lever must stop in detent over
  • Honeywell 191108AC | Owner's Manual - Page 9
    the 24 Vac transformer. Backup batteries (not included) may be installed to supply power to the clock when power is interrupted. Install batteries in thermostat as shown in Fig. 2. Once a year or when batteries are dead, replace with two new AAA alkaline batteries. We recommend Energizer batteries
  • Honeywell 191108AC | Owner's Manual - Page 10
    Setting the Clock ■ Lift thermostat flip-up cover to find the 24-hour program dial, slotted in 10-minute increments. Adjust the clock to the current time by moving the
  • Honeywell 191108AC | Owner's Manual - Page 11
    high-temperature (comfort period); a blue pin is inserted at 10:00 P.M. for low-temperature (energy saving PROGRAM PINS THERMOSTAT COVER PROGRAM PIN SLOT PROGRAM INDEX WHEEL MANUAL PROGRAM ADVANCE BUTTON PROGRAM PIN STORAGE TIME INDICATOR ARROW M7319 Fig. 4-Program Components. 11 69-0639-1
  • Honeywell 191108AC | Owner's Manual - Page 12
    period). Two additional sets of pins are located in the program pin storage area. You can set up to six temperature changes with the pins supplied. We recommend at least five hours for each energy saving period. ■ To change the pins or add a new energy saving period- • To insert a pin, push it
  • Honeywell 191108AC | Owner's Manual - Page 13
    WINTER SUMMER PROGRAM PROGRAM TEMPERATURE PIN IN TEMPERATURE PIN IN °F °C CONTROL °F °C CONTROL NIGHT BEGINS 58 14 BLUE 80 27 RED ENERGY 10:00 PM SAVING ENDS 68 20 RED 75 24 BLUE PERIOD 6:00 AM DAY BEGINS
  • Honeywell 191108AC | Owner's Manual - Page 14
    a 30-minute period before or after a program change. The manual program advance button enables immediate, one-time-only program changes to the normal setting. After pressing the button, check the program indicator on the thermostat cover to assure the system is in the desired mode. If the program
  • Honeywell 191108AC | Owner's Manual - Page 15
    Troubleshooting Your Honeywell thermostat requires little or no attention. Most problems can generally be traced to the following: Problem No heat. 2 flame. May be out. - thermostat connections. Relight pilot flame according to furnace manufacturer's instructions. Turn OFF power to furnace. Check
  • Honeywell 191108AC | Owner's Manual - Page 16
    Troubleshooting (Continued) Problem Check - other. Energy savings temperature program 12 hours time locations. - positions of thermostat set point levers. - position of subbase system switch (heating-cooling model). 16 Action Contact a qualified service technician for assistance. Turn clock
  • Honeywell 191108AC | Owner's Manual - Page 17
    Troubleshooting (Continued) Problem Room temperatures are not correct (continued). Check - thermostat circuits. 17 Action HEATING-ONLY SYSTEM-Move temperature setting levers 5° F [3° C] above room temperature. Heating system should start. If the system does not operate, call a qualified service
  • Honeywell 191108AC | Owner's Manual - Page 18
    Troubleshooting (Continued) Problem Room temperatures are not correct (continued). Check Burner-on time too short. system should start. If the system does not operate, call a qualified service technician. Increase anticipator setting by 0.05. Observe burner operation. Decrease anticipator setting
  • Honeywell 191108AC | Owner's Manual - Page 19
    Troubleshooting (Continued) Problem No cooling 1 (continued). Thermostat setting and thermometer reading disagree. Check - condenser switch position. (Located outdoors and may be turned OFF.) - thermostat connections. Check for correct terminal hookups. Repair any frayedor broken wires. Firmly
  • Honeywell 191108AC | Owner's Manual - Page 20
    Troubleshooting (Continued) Problem Thermostat setting and thermometer reading disagree. (continued). Clock does with index wheel may occur. - power. May be interrupted. Action See instructions on page 24. Remove thermostat from the wallplate or subbase and measure the voltage. Refer to the table
  • Honeywell 191108AC | Owner's Manual - Page 21
    Troubleshooting (Continued) Problem Clock loses time. (continued). Check -high limit control. If clockpowered through system in cooling-only system. If this Troubleshooting section has not solved the problem, call a qualified service technician or Honeywell Assistance Center, 1-800-468-1502,
  • Honeywell 191108AC | Owner's Manual - Page 22
    used to power the clock is inadequate. - Additional (separate) transformer used to power the clock has inadequate voltage. - Spring fingers on thermostat not making proper contact with subbase terminals. - Clock has failed. Action - Restore power. - Replace wiring. - Free or replace limit switch
  • Honeywell 191108AC | Owner's Manual - Page 23
    Servicing the Thermostat Cycle Rate Adjustment (T8095A only) The equipment should cycle on and off just enough to keep the room temperature close to the temperature lever settings. If the thermostat seems to cycle the heating system too fast or too slow, adjust the cycle rate by moving the
  • Honeywell 191108AC | Owner's Manual - Page 24
    are different, insert a small screwdriver in the thermometer slot, see Fig. 7, and turn it until both thermometers read the same. 6. Replace the thermostat cover and put the system into operation. THERMOMETER SLOT BACKSIDE OF FLIP-UP COVER INSERT AND TURN SCREWDRIVER M1810 Fig. 7-Thermometer
  • Honeywell 191108AC | Owner's Manual - Page 25
    If you have questions regarding the installation and programming of your Honeywell thermostat, please contact the Honeywell Customer Assistance Center at 1-800-468-1502, Monday-Friday, 7:30 a.m. to 4:00 p.m., Central time. Before you call, please have the following information available: make and
  • Honeywell 191108AC | Owner's Manual - Page 26
    26
  • Honeywell 191108AC | Owner's Manual - Page 27
    or materials, under normal use and service, for a period of one (1) year from the date of purchase by the consumer. If, at any time during the warranty period, the product is defective or malfunctions, Honeywell shall repair or replace it (at Honeywell's option) within a reasonable period of time
  • Honeywell 191108AC | Owner's Manual - Page 28
    Automation and Control Solutions Honeywell International Inc. Honeywell Limited-Honeywell Limitée 1985 Douglas Drive North 35 Dynamic Drive Golden Valley, MN 55422 Scarborough, Ontario M1V 4Z9
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
D.F.
•
Rev. 10-94
•
•
©Honeywell Inc. 1994
•
Form Number 69-0639—1
T8095A/191108AJ; TS8095A/191108AC; T8095A/Q682
Heating-only Thermostat and Wallplate or
Heating/Cooling Thermostat and Subbase
OWNER’S
MANUAL