Hunter 28676 Owner's Manual
Hunter 28676 Manual
 |
View all Hunter 28676 manuals
Add to My Manuals
Save this manual to your list of manuals |
Hunter 28676 manual content summary:
- Hunter 28676 | Owner's Manual - Page 1
For Your Records and Warranty Assistance For reference, also attach your receipt or a copy of your receipt to the manual. Model Name Model No. Date Purchased Where Purchased Type 2 Models Owner's Guide and Installation Manual English Español Form# 42437-01 20100608 ©2010 Hunter Fan Co. - Hunter 28676 | Owner's Manual - Page 2
Cleaning Your Ceiling Fan 14 9 • Troubleshooting 15 Welcome Your new Hunter® ceiling fan is an addition to your home or office that will provide comfort and performance for many years. This installation and operation manual gives you complete instructions for installing and operating your fan. We - Hunter 28676 | Owner's Manual - Page 3
and safe for your new Hunter fan. If you cannot check off every item, prepare a new fan site as described on this page. Fan Support System • Fan attaches directly to building structure. • Fan support system will hold full weight of the fan and light kit. Ceiling Hole • e outlet box clearance hole - Hunter 28676 | Owner's Manual - Page 4
any hardware store or electrical supply house. 5-4. Make certain the wiring meets all national and local standards and ANSI/NFPA 70. You have now successfully prepared your ceiling fan site. For instructions to install your ceiling fan, go to your fan manual and continue with Section 2 • Installing - Hunter 28676 | Owner's Manual - Page 5
, follow the instructions included with each product. For quiet and optimum performance of your Hunter fan, use only Hunter speed controls. Support Brace Ceiling Outlet Box For ceilings higher than 8 feet, you can purchase Hunter extension downrods. All Hunter fans use sturdy 3/4" diameter - Hunter 28676 | Owner's Manual - Page 6
sure you can do the following: • Locate the ceiling joist or other suitable support in ceiling. • Drill holes for and install wood screws. • Identify and connect electrical wires. • Lift 40 pounds. If you need help installing the fan, your Hunter fan dealer can direct you to a licensed installer or - Hunter 28676 | Owner's Manual - Page 7
service panel. 2-1. Drill two pilot holes into the wood support structure through the outermost holes in the outlet box. The pilot holes should be 9/64" in diameter. For Angled Ceilings: Be sure to orient the ceiling plate so that the two tabs are pointing toward the ceiling peak. 2-2. Your fan - Hunter 28676 | Owner's Manual - Page 8
and Hanging the Fan WARNING: Fan may fall if not assembled as directed in these installation instructions. 3-1. Unbundle the wires from the fan. For Standard or Angled mounting: 3-2. Insert the downrod through the canopy and canopy trim ring. Feed the wires from the fan through the downrod - Hunter 28676 | Owner's Manual - Page 9
back through the ceiling plate into the outlet box. 4-7. Spread the wires apart, with the grounded wires on one side of the outlet box and the ungrounded wires on the other side of the outlet box. 9 42437-01 • 06/08/10 • Hunter Fan Company Wire Connector Dual Switch Wiring Single Switch Wiring - Hunter 28676 | Owner's Manual - Page 10
hanger ball groove. Note: Your fan may have multiple tabs and grooves that must be aligned. 5-2. Swing the fan up to align the canopy screw holes with the mounting holes on the ceiling plate. WARNING: The slots in 5-3 Canopy Canopy Trim Ring Canopy Screw 10 42437-01 • 06/08/10 • Hunter Fan Company - Hunter 28676 | Owner's Manual - Page 11
the Blades Our blade assembly enables you to lock the blades in place without tools and to separated from the blade iron. 3. Carefully remove the blade. Note: The blades on this fan have been treated with Hunter's Dust Armor protection, making the blades less likely to attract dust and dirt. Use a - Hunter 28676 | Owner's Manual - Page 12
Screw Plug Connector WARNING: Use only the light fixture supplied with this fan model. 7-1. To attach the lower switch housing assembly to the fan, partially install two housing assembly screws into the upper switch housing. 7-2. Connect the upper plug connector from the motor to the lower - Hunter 28676 | Owner's Manual - Page 13
7-8. Install B10 candelabra-based light bulbs (40 Watt maximum each). Shade Note: In compliance with US federal energy regulations, this Bulb ceiling fan contains a device that restricts its light Thumbscrews output. Exceeding the wattage limit marked on the MAX wattage sticker affixed to the - Hunter 28676 | Owner's Manual - Page 14
the light fixture. The chain has two settings: ON and OFF. 8-4. Ceiling fans work best by blowing air downward (counterclockwise blade rotation) in warm weather to cool the room with a direct breeze. In winter, having the fan draw air upward (clockwise blade rotation) will distribute the warmer air - Hunter 28676 | Owner's Manual - Page 15
9 • Troubleshooting Problem: Nothing happens; fan does not move 1. Turn power on, replace fuse, or reset breaker. 2. Loosen canopy, check all connections according to the wiring the fan section. 3. Check the plug connection in the switch housing. 4. Push motor reversing switch firmly left or right
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
 |
 |
Type 2 Models
Type 2 Models
Type 2 Models
Form# 42437-01
20100608
©2010 Hunter Fan Co.
For Your Records and
Warranty Assistance
For reference, also attach your receipt or a copy
of your receipt to the manual.
__________________________________________
Model Name
__________________________________________
Model No.
__________________________________________
Date Purchased
__________________________________________
Where Purchased
English
Español
Owner’s Guide and Installation Manual