Husqvarna Z246i Owners Manual

Husqvarna Z246i Manual

Get Husqvarna Z246i PDF manuals and user guides View all Husqvarna Z246i manuals
Add to My Manuals
Save this manual to your list of manuals

Husqvarna Z246i manual content summary:

  • Husqvarna Z246i | Owners Manual - Page 1
    Operator Manual Z 246i Zero Turn Mower / 967323901-00 Please read the operator manual carefully and make sure you understand the instructions before using the machine. Gasoline containing up to 10% ethanol (E10) is acceptable for use in this machine.The use of any gasoline exceeding 10%
  • Husqvarna Z246i | Owners Manual - Page 2
    . The use of other parts voids the warranty. Do not modify or install non-standard equipment to the unit without consent from the manufacturer. Modifications to the unit may cause unsafe operations or damage the unit. WARNING! Battery posts, terminals and related accessories contain lead and lead
  • Husqvarna Z246i | Owners Manual - Page 3
    Belt Removal 28 Adjusting the Mower Deck 29 Leveling deck 29 Cutting Blades 30 Blade replacement 30 Cleaning 30 LUBRICATION 31 Transmission 31 Wheel and Deck Zerks 31 Front Wheel Mount 31 Front Wheel Bearings 31 Deck Spindles 31 TROUBLESHOOTING 32 STORAGE 33 Winter Storage 33 Service
  • Husqvarna Z246i | Owners Manual - Page 4
    dealer for service. General In this operator manual, left and right, backward and forward are used in relation to the machine's normal driving direction. Continuous dedication to improve our products require that specifications and design are subject to change without notice. Driving and Transport
  • Husqvarna Z246i | Owners Manual - Page 5
    adjusted by your retailer. See the certificate in the Service Journal in this operator manual. When you need spare parts or support in service questions, warranty issues, etc., please consult the following professional: This Manual belongs to the machine with the manufacturing number: Manufacturing
  • Husqvarna Z246i | Owners Manual - Page 6
    should neglect to follow instructions given in the manual. Used also when there is a potential for misuse or misassembly. Cold Weather Fuel Warning! Park Brake Start Cut Height Low Cut Height High Blades Steering Controls Headlights Battery Do not stand here Battery acid is corrosive
  • Husqvarna Z246i | Owners Manual - Page 7
    . Always turn off blades, move the steering control lever outward to the park brake position and stop the engine before dismounting. • Never carry passengers. The machine is only intended for use by one person. • Disengage blades when not mowing. Shut off engine and wait for all parts to come
  • Husqvarna Z246i | Owners Manual - Page 8
    10 degrees. Do not drive across any slopes. • Choose a low ground speed so that you will not have to stop while on the slope. • Do not mow on wet grass. Tires may lose traction. • Avoid starting, stopping, or turning on a slope. If the tires lose traction, disengage the blades and proceed slowly
  • Husqvarna Z246i | Owners Manual - Page 9
    the blade attachments, are properly tightened and torqued. • Maintain or replace safety and instruction labels mower deck's drive belt is removed. • Check grass catcher components and the discharge guard frequently and replace with manufacturer's recommended parts when necessary. • Do not change
  • Husqvarna Z246i | Owners Manual - Page 10
    SAFETY Safety System The machine is equipped with a safety system that prevents starting or driving under the following conditions. The engine can only be started when: • The mower blades are disengaged. • The motion control levers are in neutral. After the machine is started, the engine will
  • Husqvarna Z246i | Owners Manual - Page 11
    drive system. • Do not tow any trailers, etc. with this mower. They may jackknife or overturn, causing damage to the mower or others in or on towed equipment.. Make wide turns to avoid jack-knifing. Travel slowly and allow extra available through your authorized Husqvarna dealer. WARNING! Engine
  • Husqvarna Z246i | Owners Manual - Page 12
    manual describes the Husqvarna Zero Turn Rider. The rider is fitted with a Briggs & Stratton four-stroke overhead valve engine. Transmission from the engine is made via a belt valve 7. Fuel tank 8. Throttle control 9. Service meter 10. Ignition switch 11. Blade switch 12. Seat adjustment lever 12
  • Husqvarna Z246i | Owners Manual - Page 13
    The rotation of the right wheel is reduced and the machine turns to the right. Zero turn can be achieved by moving one control backward (behind the brake before dismounting. Release the park brake before moving the mower. Ignition Switch The ignition switch is placed on the control panel and is
  • Husqvarna Z246i | Owners Manual - Page 14
    plugs. USE FULL THROTTLE WHEN MOWING, for best mower performance and battery charging. The service meter displays the total number of hours the engine has run and indicates when the engine and mower need servicing. After every 50 hours of operation, an oil can icon will appear and stay on for two
  • Husqvarna Z246i | Owners Manual - Page 15
    Off Valve Transaxle bypass linkages must be engaged when pushing or pulling the mower. The release levers are located on each side of the rear of the rear of the seat. The valve is off when the handle tab is turned perpendicular to the fuel line. 15 WARNING! Bypass linkages are located close to
  • Husqvarna Z246i | Owners Manual - Page 16
    To avoid engine problems, the fuel system oil or fuel. Do not store, spill or use gasoline near an open flame. Read the safety instructions weather starting. If the mower is not tracking straight, driving it at full throttle and the full forward position on both motion control levers. Gradually turn
  • Husqvarna Z246i | Owners Manual - Page 17
    zero turn mowers are far more maneuverable than typical riding mowers. This section should be reviewed in its entirety prior to attempting to move the mower under its own power. When first operating the mower blades. As long as the control levers have not been moved forward or backwards, the mower
  • Husqvarna Z246i | Owners Manual - Page 18
    full throttle position. NOTE: There is a detent at the full throttle position to aid in setting the control. 3. Disengage the mower blades by pressing the blade switch downwards. If the temperature is below 32OF, move the throttle lever up to the cold weather (snowflake) starting position. When
  • Husqvarna Z246i | Owners Manual - Page 19
    SmartSwitch Ignition is programmed to warn when any part of the safety system is not being followed are resolved. The blade switch fault light will blink if the blade control switch has not one slow green blink if the code is accepted and will change to a rapid green blink. If the S/S button has
  • Husqvarna Z246i | Owners Manual - Page 20
    switch. Make sure the work area is free from objects that could be thrown by the rotating blades. 4. Raise the mower deck to the highest position. If the engine has been worked hard, allow it to idle at least 60 seconds to attain a normal operating temperature
  • Husqvarna Z246i | Owners Manual - Page 21
    until finished. Operating On Hills Read the Safety Instructions Driving on Slopes in the Safety section. • The slowest speed possible should be used before starting up or down hills. • Avoid stopping or changing speed on hills and make all turns slowly. • If stopping is absolutely necessary, pull
  • Husqvarna Z246i | Owners Manual - Page 22
    . The S/S button indicator will show red (battery charge level is low), multi-colored (battery charge is marginal) or green (battery level is good) until the battery button is pressed again or is allowed to reset after ten seconds. IMPORTANT INFORMATION The mower is equipped with a 12-volt negative
  • Husqvarna Z246i | Owners Manual - Page 23
    pulling the mower, engage the bypass position. 4. To reengage the EZT's to drive, reverse the above procedure. WARNING! Bypass linkages are located : • the engine stopped, • the ignition switch turned off, • the park brake activated WARNING! Use driving slowly up the ramps. DO NOT LIFT! The
  • Husqvarna Z246i | Owners Manual - Page 24
    clean around the engine Clean around belts, belt pulleys Check the tire pressures Check battery connections Sharpen3)/ Replace mower blades Clean the engine's cooling air intake 2) Clean the foam air cleaner prefilter 2) Clean the paper air cleaner filter cartridge 2) Check/adjust the park brake
  • Husqvarna Z246i | Owners Manual - Page 25
    the condition of belts, belt pulleys Change the engine oil 1) Replace the engine oil filter Clean/replace the spark plugs Replace the fuel filter Replace paper air filter 2) Check the caster wheels (every 200 hours) Replace the air cleaner's foam pre-filter 2) Check/adjust the mower deck Check the
  • Husqvarna Z246i | Owners Manual - Page 26
    MAINTENANCE Battery Your mower is equipped with a maintenance free battery that does not need servicing. However, periodic charging of the battery with an automotive type battery charger will extend its life. • Keep battery and terminals clean. • Keep battery bolts tight. • See chart for charging
  • Husqvarna Z246i | Owners Manual - Page 27
    park brake, contact the Husqvarna service workshop. IMPORTANT INFORMATION Change the conditions and try again. If the machine starts when one of these conditions is not met, turn mower blades are engaged and the driver temporarily moves off the drivers seat. IMPORTANT INFORMATION To be able to drive
  • Husqvarna Z246i | Owners Manual - Page 28
    the unit to your dealer for service. Foam filled tires or solid tires mower on a flat level surface. To avoid deck damage, the anti-scalp rollers must not be adjusted to support the deck. 7. Carefully lift the belt over the top of the cutter housing pulleys and remove belt from the deck. Deck Belt
  • Husqvarna Z246i | Owners Manual - Page 29
    higher in the rear. NOTE: To insure accuracy of leveling procedure, mower deck drive belt must be installed prior to leveling deck. 1. Wear heavy gloves. Turn each blade tip to align front to rear with the deck side-to-side. 4. Turn either blade to align with the deck front-to-rear. If the front
  • Husqvarna Z246i | Owners Manual - Page 30
    attach the quick connect (from the accessory packet) to any garden hose. After mowing, snap the hose to the cleanout port and turn on water supply. Blade replacement 1. Remove blade bolt by turning counter clockwise. 2. Install new or resharpened blade with stamped GRASS SIDE facing towards ground
  • Husqvarna Z246i | Owners Manual - Page 31
    Use minimal lubrication and remove excess lubricant so that is does not come into contact with belts or belt pulley drive surfaces. Transmission The transmission is maintenance free with no need for level checks or oil changes. If a leak occurs, replace the unit or contact your Husqvarna dealer. 31
  • Husqvarna Z246i | Owners Manual - Page 32
    TROUBLESHOOTING Problem / Cause Engine will not start Blade switch is engaged Steering controls are not locked in the outer position Battery is dead Contamination in the carburetor or fuel line Fuel supply shutoff valve is closed Clogged fuel filter or fuel line Ignition system faulty Starter does
  • Husqvarna Z246i | Owners Manual - Page 33
    store the battery in a cool place, but protect it from direct cold. 8. Store the machine in a clean, dry place and cover it for extra protection. Service When ordering spare parts, please specify the purchase year, model, type, and serial number. Always use genuine Husqvarna spare parts. An annual
  • Husqvarna Z246i | Owners Manual - Page 34
    SCHEMATIC 34
  • Husqvarna Z246i | Owners Manual - Page 35
    Cutting Height 23 HP 1) Uncut Circle Pressure with oil filter Number of Blades Min 87 octane unleaded (Max Blade Length ethanol 10%, Max MTBE 15%) 3½ gallons / 13.25 litres Anti-scalp Rollers Air cooled Sprung Seat Standard Hinged Arm Rests 12V Service Meter Electric Blade Engagement
  • Husqvarna Z246i | Owners Manual - Page 36
    DATA Engine crankshaft bolt Deck pulley bolts Lug nuts Blade bolt Torque Specifications 75 ft/lb (102 Nm) Nm) 33 ft/lb (44 Nm) 52 ft/lb (70 Nm) 80 ft/lb (110 Nm) Accessories Collection system HEX HEAD CAP SCREWS The torque values shown should be used as a general guideline when specific
  • Husqvarna Z246i | Owners Manual - Page 37
    Safety switch for the park brake q Safety switch for the mower deck q Safety switch in the seat q Safety switch in the steering controls q Park brake functionality q Driving forward q Driving backward q Engaging the blades q Check the idle speed q Check the engine high idle speed
  • Husqvarna Z246i | Owners Manual - Page 38
    Action After the First 10 Hours Change engine oil SERVICE JOURNAL Date, mtr reading, stamp, sign q 25-Hour Service Check the fuel pump's air filter Sharpen/Replace mower blades if required Check the tire pressures Check battery cables Lubricate according to lubrication chart Check / clean the
  • Husqvarna Z246i | Owners Manual - Page 39
    the 25-hour service Perform the 50-hour service Change the engine oil filter Clean/replace the spark plugs Replace the fuel filter Check V-belts Check / tighten caster wheel axle bolts (every 200 hours) Change the air filter's paper cartridge Change hydraulic pump oil and filter. (200 hours) Date
  • Husqvarna Z246i | Owners Manual - Page 40
    SERVICE JOURNAL Action At Least Once Each Year Clean the engine's cooling air intake (25 hours) Replace the air cleaner's foam pre-filter (300 hours) Replace the air filter's paper cartridge Change the engine oil (50 hours) Replace the engine oil filter (100 hours) Check / adjust the cutting height
  • Husqvarna Z246i | Owners Manual - Page 41
    Action SERVICE JOURNAL Date, mtr reading, stamp, sign 41
  • Husqvarna Z246i | Owners Manual - Page 42
    Action SERVICE JOURNAL Date, mtr reading, stamp, sign 42
  • Husqvarna Z246i | Owners Manual - Page 43
  • Husqvarna Z246i | Owners Manual - Page 44
    www.husqvarna.com 115 73 82-27 Rev B 2015-01-30
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
Operator Manual
Z 246i
Zero Turn
Mower / 967323901-00
Please read the operator manual carefully and make sure
you understand the instructions before using the machine.
Gasoline containing up to 10% ethanol (E10) is acceptable for use in
this machine.The use of any gasoline exceeding 10%
ethanol (E10)
will void
the product warranty.
EN