Icom IC-F4230D Instructions

R

DANGER! NEVER

short the terminals of the battery

pack. Shorting may occur if the terminals touch metal

objects such as a key, so be careful when placing the

battery packs (or the transceiver) in bags, and so on.

Carry them so that shorting cannot occur with metal

objects. Shorting may damage not only the battery pack,

but also the transceiver.

R

DANGER! NEVER

use or charge Icom battery packs

with non-Icom transceivers or non-Icom chargers. Only

Icom battery packs are tested and approved for use with

Icom transceivers or charged with Icom chargers. Using

third-party or counterfeit battery packs or chargers may

cause smoke, fire, or cause the battery to burst.

R

DANGER! NEVER

operate the transceiver near

unshielded electrical blasting caps or in an explosive

atmosphere.

R

WARNING! NEVER

hold the transceiver so that the

antenna is very close to, or touching exposed parts of the

body, especially the face or eyes, while transmitting. The

transceiver will perform best if the microphone is 5 to 10

cm (2 to 4 inches) away from the lips and the transceiver

is vertical.

R

WARNING! NEVER

operate the transceiver with a

headset or other audio accessories at high volume levels.

The continuous high volume operation may cause a

ringing in your ears. If you experience the ringing, reduce

the volume level or discontinue use.

CAUTION: DO NOT

use harsh solvents such as Benzine

or alcohol when cleaning. This could damage the

equipment surfaces. If the surface becomes dusty or dirty,

wipe it clean with a soft, dry cloth.

CAUTION: DO NOT

place or leave the transceiver in

excessively dusty environments. This could damage the

transceiver.

CAUTION: DO NOT

expose the transceiver to rain, snow

or any liquids. The transceiver meets IP67* requirements

for dust-tight and waterproof protection. However, once the

transceiver has been dropped, dust-tight and waterproof

protection cannot be guaranteed due to the fact that

the transceiver may be cracked, or the waterproof seal

damaged, and so on.

*Only when the jack cover or the optional HM-168LWP is

attached.

Your Icom radio generates RF electromagnetic

energy while transmitting. This radio is designed

for and classified as for “Occupational Use Only.”

This means it must be used only during the

course of employment by individuals aware of

the hazards, and the ways to minimize such hazards. This

radio is NOT intended for use by the “General Population”

in an uncontrolled environment. This radio has been tested

and complies with the FCC and IC RF exposure limits for

“Occupational Use Only”. In addition, your Icom radio

complies with the following Standards and Guidelines with

regard to RF energy and electromagnetic energy levels

and evaluation of such levels for exposure to humans:

•

FCC OET Bulletin 65 Edition 97-01 Supplement C,

Evaluating Compliance with FCC Guidelines for Human

Exposure to Radio Frequency Electromagnetic Fields.

•

American National Standards Institute (C95.1-1992),

IEEE Standard for Safety Levels with Respect to

Human Exposure to Radio Frequency Electromagnetic

Fields, 3 kHz to 300 GHz.

•

American National Standards Institute (C95.3-1992),

IEEE Recommended Practice for the Measurement of

Potentially Hazardous Electromagnetic Fields– RF and

Microwave.

•

The following accessories are authorized for use with

this product. Use of accessories other than those

specified may result in RF exposure levels exceeding

the FCC and IC requirements for wireless RF

exposure.; Belt Clip (MB-93, MB-94/R and MB-96N/F),

Rechargeable Li-ion Battery Pack (BP-232WP) and

Speaker-microphone (HM-158LA/HM-159LA/HM-

168LWP).

To ensure that your expose to RF

electromagnetic energy is within the FCC and IC

allowable limits for occupational use, always

adhere to the following guidelines:

DO NOT

operate the radio without a proper antenna

attached, as this may damage the radio and may also

cause you to exceed FCC and IC RF exposure limits. A

proper antenna is the antenna supplied with this radio by

the manufacturer or an antenna specifically authorized by

the manufacturer for use with this radio.

DO NOT

transmit for more than 50% of the total radio use

time (“50% duty cycle”). Transmitting more than 50% of

the time can cause FCC and IC RF exposure compliance

requirements to be exceeded. The radio is transmitting

when the LED indicator lights red. You can cause the radio

to transmit by pushing the “PTT” switch.

ALWAYS keep the antenna at least 2.5 cm (1 inch) away

from the body when transmitting, and only use the Icom

belt-clips listed in “OPTIONS” of the INSTRUCTIONS

sheet when attaching the radio to your belt, or other

place, to ensure FCC and IC RF exposure compliance

requirements are not exceeded.

The information listed above provides the user with

the information needed to make him or her aware of

RF exposure, and what to do to assure that this radio

operates within the FCC and IC RF exposure limits of this

radio.

1-1-32 Kamiminami, Hirano-ku,

Osaka 547-0003, Japan

A7082D-1EX-4a

Printed in Japan

© 2013–2021 Icom Inc.

Icom is not responsible for the destruction, damage to, or

performance of any Icom or non-Icom equipment, if the

malfunction is because of:

•

Force majeure, including, but not limited to, fires,

earthquakes, storms, floods, lightning, other natural

disasters, disturbances, riots, war, or radioactive

contamination.

•

The use of Icom transceivers with any equipment that

is not manufactured or approved by Icom.

FCC INFORMATION

This equipment has been tested and found to comply

with

the limits for a Class A digital device, pursuant to part 15

of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when

the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and used

in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation

of this equipment in a residential area is likely to cause

harmful interference in which case the user will be

required to correct the interference at his own expense.

CAUTION:

Changes or modifications to this transceiver,

not expressly approved by Icom Inc., could void

your authority to operate this transceiver under FCC

regulations.

This device complies with Part 15 of the FCC Rules.

Operation is subject to the condition that this device does

not cause harmful interference.

RECOMMENDATION

CLEAN THE TRANSCEIVER THOROUGHLY IN A BOWL

OF FRESH WATER

after exposure to saltwater, and dry

it before operating. Otherwise, the transceiver’s keys,

switches, and controllers may become unusable, due to

salt crystallization, and/or the charging terminals of the

battery pack may corrode.

NOTE:

If the transceiver’s waterproof protection appears

defective, carefully clean the transceiver with a soft,

damp (fresh water) cloth, then dry it before operating. The

transceiver may lose its waterproof protection if the case,

jack cap, or connector cover is cracked or broken, or the

transceiver has been dropped.

Contact your Icom distributor or your dealer for advice.

VOICE CODING TECHNOLOGY

The AMBE+2™ voice coding Technology embodied in this

product is protected by intellectual property rights including

patent rights, copyrights and trade secrets of Digital Voice

Systems, Inc. This voice coding Technology is licensed

solely for use within this Communications Equipment.

The user of this Technology is explicitly prohibited from

attempting to extract, remove, decompile, reverse

engineer, or disassemble the Object Code, or in any other

way convert the Object Code into a human-readable form.

U.S. Patent Nos.

#8,595,002, #8,359,197, #8,315,860, #8,200,497,

#7,970,606, #6,912,495 B2.

Icom, Icom Inc. and the Icom logo are registered

trademarks of Icom Incorporated (Japan) in Japan, the

United States, the United Kingdom, Germany, France,

Spain, Russia, Australia, New Zealand, and/or other

countries.

AMBE+2 is a trademark and property of Digital Voice

Systems Inc.

All other products or brands are registered trademarks or

trademarks of their respective holders.

DO NOT

place or leave the transceiver in direct sunlight or

in areas outside of the specified temperature range:

–30°C (–22°F) ~ +60°C (+140°F)

Keep the transceiver in a secure place to prevent use by

unauthorized persons.

D

Battery caution

Misuse of Li-ion batteries may result in the following

hazards: smoke, fire, or the battery may rupture. Misuse

can also cause damage to the battery or degradation of

battery performance.

R

DANGER! NEVER

solder the battery terminals, or

NEVER modify the battery pack. This may cause heat

generation, and the battery may burst, emit smoke or

catch fire.

R

DANGER! NEVER

place or leave battery packs in

areas with temperatures above 60°C (140°F). High

temperature buildup in the battery cells, such as could

occur near fires or stoves, inside a sun-heated vehicle,

or in direct sunlight for long periods of time may cause

the battery cells to rupture or catch fire. Excessive

temperatures may also degrade the battery pack’s

performance or shorten the battery cell’s life.

R

DANGER! NEVER

strike or otherwise impact the

battery pack. Do not use the battery pack if it has been

severely impacted or dropped, or if the pack has been

subjected to heavy pressure. Battery pack damage may

not be visible on the outside of the case. Even if the

surface of the battery does not show cracks or any other

damage, the cells inside the battery may rupture or catch

fire.

R

DANGER! NEVER

expose the battery pack to rain,

snow, seawater, or any other liquids. Do not charge or

use a wet pack. If the pack gets wet, be sure to wipe it dry

before using.

R

DANGER! NEVER

place or leave battery packs near

fire. Fire or heat may cause them to rupture or explode.

Dispose of used battery packs in accordance with local

regulations.

R

DANGER! NEVER

let fluid from inside the battery get

in your eyes. This can cause blindness. Rinse your eyes

with clean water, without rubbing them, and immediately

go to a doctor.

R

WARNING! NEVER

put the battery pack in a microwave

oven, high-pressure container, or in an induction heating

cooker. This could cause a fire, overheating, or cause the

battery cells to rupture.

R

WARNING! NEVER

use the battery pack if it emits an

abnormal odor, heats up, or is discolored or deformed. If

any of these conditions occur, contact your Icom dealer or

distributor.

R

WARNING! NEVER

Iet fluid from inside the battery cells

come in contact with your body. If it does, immediately

wash with clean water.

CAUTION: DO NOT

use the battery pack out of the

specified temperature range for the transceiver (–30°C

~ +60°C (–22°F ~ +140°F)) and the battery itself (–20°C

~ +60°C (–4°F ~ +140°F)). Using the battery out of its

specified temperature range will reduce its performance

and battery cell’s life. Please note that the specified

temperature range of the battery may exceed that of the

transceiver. In such cases, the transceiver may not work

properly because it is out of its operating temperature

range.

CAUTION: DO NOT

leave the pack fully charged,

completely discharged, or in an excessive temperature

environment (above 60°C, 140°F) for an extended

period of time. If the battery pack must be left unused

for a long time, it must be detached from the transceiver

after discharging. You may use the battery pack until the

remaining capacity is about half, then keep it safely in a

cool and dry place at the following temperature range:

–20°C ~ +50°C (–4°F ~ +122°F) (within a month)

–20°C ~ +40°C (–4°F ~ +104°F) (within three months)

–20°C ~ +20°C (–4°F ~ +68°F) (within a year)

BE SURE

to replace the battery pack with a new one

approximately five years after manufacturing, even if it still

holds a charge. The material inside the battery cells will

become weak after a period of time, even with little use.

The estimated number of times you can charge the pack

is between 300 and 500. Even when the pack appears to

be fully charged, the operating time of the transceiver may

become short when:

•

Approximately 5 years have passed since the pack was

manufactured.

•

The pack has been repeatedly charged.

D

Charging caution

R

DANGER! NEVER

charge the battery pack in areas

with extremely high temperatures, such as near fires or

stoves, inside a sun-heated vehicle, or in direct sunlight.

In such environments, the safety/protection circuit in the

battery will activate, causing the battery to stop charging.

R

WARNING! NEVER

charge the transceiver during a

lightning storm. It may result in an electric shock, cause

a fire or damage the transceiver. Always disconnect the

power adapter before a storm.

R

WARNING! NEVER

charge or leave the battery in the

battery charger beyond the specified time for charging. If

the battery is not completely charged by the specified time,

stop charging and remove the battery from the battery

charger.

Continuing to charge the battery beyond the specified time

limit may cause a fire, overheating, or the battery may

rupture.

R

WARNING! NEVER

insert the transceiver (battery

attached to the transceiver) into the charger if it is wet or

soiled. This could corrode the battery charger terminals or

damage the charger. The charger is not waterproof.

CAUTION: DO NOT

charge the battery outside of the

specified temperature range:

BC-160/BC-171:

(0˚C ~ 45˚C (32˚F ~ 113˚F))

BC-119N/BC-121N/BC-197: (10˚C ~ 40˚C (50˚F ~ 104˚F))

Otherwise, the charging time will be longer, but the battery

will not reach a full charge. While charging, at a point

after the temperature goes out of the specified range, the

charging will automatically stop.

PRECAUTIONS

PANEL DESCRIPTION

SAFETY TRAINING INFORMATION

Electromagnetic Interference/Compatibility

During transmissions, your Icom radio generates RF

energy that can possibly cause interference with other

devices or systems. To avoid such interference, turn off

the radio in areas where signs are posted to do so. DO

NOT operate the transmitter in areas that are sensitive to

electromagnetic radiation such as hospitals, aircraft, and

blasting sites.

Occupational/Controlled Use

The radio transmitter is used in situations in which persons

are exposed as a consequence of their employment,

provided those persons are fully aware of the potential for

exposure and can exercise control over their exposure.

ATTACHING ACCESSORIES

D

Flexible antenna

Connect the antenna to the antenna connector.

CAUTION:

•

DO NOT

carry the transceiver by holding only the

antenna.

•

DO NOT

connect an antenna other than those listed in

the INSTRUCTIONS.

•

Transmitting without an antenna may damage the

transceiver.

D

Battery pack

CAUTION: DO NOT

attach or detach the battery pack

when the transceiver is wet or soiled. This may result in

water or dust getting into the transceiver/battery pack and

may damage the transceiver.

To attach:

Slide the battery pack in the direction of the arrow (

1

)

until the battery release button makes a ‘click’ sound.

NOTE:

Push on the bottom of the pack to make sure the

release button is firmly locked.

To detach:

Slide the battery release button in the direction of the

arrow (

2

) as shown below. The battery pack is then

detached.

EXPLICIT DEFINITIONS

WORD

DEFINITION

R

DANGER!

Personal death, serious injury or an

explosion may occur.

R

WARNING!

Personal injury, fire hazard or electric

shock may occur.

CAUTION

Equipment damage may occur.

NOTE

If disregarded, inconvenience only. No

risk of personal injury, fire or electric

shock.

IMPORTANT

This instruction sheet includes some functions that are

usable only when they are preset by your dealer. The

transceiver may have other functions and operations that

are not described in this instruction sheet. Ask your dealer

for preset function details.

VHF DIGITAL TRANSCEIVERS

Thank you for choosing this Icom product.

READ ALL INSTRUCTIONS

carefully and completely

before using this product.

iF3230D

Series

UHF DIGITAL TRANSCEIVERS

iF4230D

Series

SUPPLIED ACCESSORIES

NOTE:

Some accessories are not supplied, or the shape

is different, depending on the transceiver version.

Battery pack

Belt clip

Battery charger

Power adapter

Flexible antenna

Battery release button

1

2

[VOL]

External

microphone/

speaker jack

Speaker

[PTT]

[Side1]

[Emer]

[Side2]/

[Side3]

[P0]/[P1]/

[P2]/[P3]

Function

Display

Microphone

Antenna

Connector

D

About the External microphone/speaker jack

Connects to an optional speaker microphone or speaker.

CAUTION: DO NOT

use the transceiver without the jack

cover or the optional equipment attached.

The transceiver meets IP67 requirements for dust-tight

and waterproof protection only when the jack cover or the

optional HM-168LWP is attached.

D

About the Assignable key functions

NOTE:

Your dealers can assign the functions to the keys

and keypads.

Jul. 2021

INSTRUCTIONS

Icom IC-F4230D Instructions

Icom IC-F4230D Manual

Icom IC-F4230D manual content summary: