InSinkErator Invite H990-SS Owners Manual - Page 2

What You Should Know Before You Begin, What You Need To Get Started - parts

Get InSinkErator Invite H990-SS PDF manuals and user guides View all InSinkErator Invite H990-SS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 2 highlights

We are delighted that you have chosen the InSinkErator® Instant Hot Water Dispenser to be a part of your home. This unique appliance will save you time and effort in the kitchen, and you'll enjoy discovering new uses for it each day. That's exactly why millions of people are now using an InSinkErator Instant Hot Water Dispenser. We are confident that by following our step-by-step instructions, you'll soon be enjoying the convenience of instant hot water. WHAT YOU SHOULD KNOW BEFORE YOU BEGIN I For your satisfaction and safety, read all instructions, cautions, warnings and dangers before installing or using this instant hot water dispenser. I This particular unit is not intended for commercial use. I Make sure that all electrical wiring and connections conform to local codes. I A standard 120-volt grounded electrical outlet is required under the sink for the dispenser's electrical power. I The wall outlet powering your dispenser must have power supplied to it continuously. I This outlet must be fused and should not be controlled by the same wall switch that operates the disposer, unless you have a SinkTop Switch™ from InSinkErator®. I It is recommended that a dedicated control valve be installed on the cold water line supplying water to this system. I If you suspect elevated levels of chlorine in your water, it is recommended to use our water filtration system. I The use of a water filter should NOT result in the water pressure to drop below 30 psi (207kPa). If it does, this will prevent your unit from operating properly. I Moving parts inside the tank causing a rattling noise is normal. WHAT YOU NEED TO GET STARTED Equipment Required: I Drill I T-fitting I Dedicated control valve I Adjustable wrench I Phillips and flat blade screwdrivers I Pencil I Tape measure I Level Equipment You May Need: I Anchors for drywall I Hole saw I Basin wrench I Hole punch If you intend to use the sprayer hole in your sink for your dispenser, you may need a basin wrench and a 1/8" plug or a 1/4" cap (not supplied) for the faucet spray hose line. See Step 1-B. If you need to cut a mounting hole in your stainless steel sink, you may need a 11⁄4" - 11⁄2" hole saw made for cutting stainless steel or a hole punch. Consult a professional if you are drilling into a surface other than stainless steel. 2

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
Equipment You May Need:
We are delighted that you have chosen the InSinkErator
®
Instant Hot Water Dispenser
to be a part of your home. This unique appliance will save you time and effort in the
kitchen, and you’ll enjoy discovering new uses for it each day. That’s exactly why
millions of people are now using an InSinkErator Instant Hot Water Dispenser.
We are confident that by following our step-by-step instructions, you’ll soon be enjoying
the convenience of instant hot water.
■
For your satisfaction and safety, read all instructions, cautions, warnings and dangers before installing
or using this instant hot water dispenser.
■
This particular unit is not intended for commercial use.
■
Make sure that all electrical wiring and connections conform to local codes.
■
A standard 120-volt grounded electrical outlet is required under the sink for the dispenser’s electrical power.
■
The wall outlet powering your dispenser must have power supplied to it continuously.
■
This outlet must be fused and should not be controlled by the same wall switch that operates the
disposer, unless you have a SinkTop Switch
™
from InSinkErator
®
.
■
It is recommended that a dedicated control valve be installed on the cold water line supplying water
to this system.
■
If you suspect elevated levels of chlorine in your water, it is recommended to use our water
filtration system.
■
The use of a water filter should NOT result in the water pressure to drop below 30 psi (207kPa).
If it does, this will prevent your unit from operating properly.
■
Moving parts inside the tank causing a rattling noise is normal.
WHAT YOU SHOULD KNOW BEFORE YOU BEGIN
Equipment Required:
■
Drill
■
T-fitting
■
Dedicated control valve
■
Adjustable wrench
■
Phillips and flat blade screwdrivers
■
Pencil
■
Tape measure
■
Level
■
Anchors for drywall
■
Hole saw
■
Basin wrench
■
Hole punch
If you intend to use the sprayer hole in your sink for your dispenser, you may need a basin wrench and a
1/8" plug or a 1/4" cap (
not supplied
) for the faucet spray hose line.
See Step 1-B.
If you need to cut a mounting hole in your stainless steel sink, you may need a 1
1
±
4
" - 1
1
±
2
" hole saw made
for cutting stainless steel or a hole punch. Consult a professional if you are drilling into a surface other
than stainless steel.
WHAT YOU NEED TO GET STARTED
2