Insignia NS-CZ18XWH7 Quick Setup Guide

Three screws (provided)

QUICK SETUP GUIDE

WiFi Connected

13.8 Cu.Ft. Upright

Freezer

NS-UZ14XWH7

Before using your new product, please read these instructions to prevent any damage.

SETTING UP YOUR FREEZER

Before using your freezer

•

Remove the exterior and interior packing.

•

Let the freezer stand upright for approximately two hours

before connecting it to power.

•

Wipe the inside.

•

When moving your freezer, do not tilt it beyond 45° from

upright.

Finding a suitable location

•

This freezer is designed to be free standing only, and should

not be recessed or built-in.

•

Place your freezer on a floor that is strong enough to support

the freezer when it is fully loaded.

•

If your freezer is located too far from your WiFi router, the

signal may be too weak for a good connection. If that’s the

case, a WiFi range extender should improve connectivity.

•

Allow 7.9 inches (20 cm) of space between the sides of the

freezer and the walls, 3.9 inches (10 cm) between the back

of the freezer and the wall, and 11.8 inches (30 cm)

between the top of the freezer and the ceiling.

•

If you locate the freezer next to a fixed wall, allow sufficient

space on the hinge side for the door to swing open.

•

Locate the freezer away from direct sunlight and sources of

heat, such as a stove, heater, or radiator. Direct sunlight may

affect the acrylic coating and heat sources may increase

electrical consumption. Extremely cold temperatures may

also prevent the freezer from performing properly.

•

Avoid locating the freezer in moist areas.

Leveling your freezer

•

It is very important for the freezer to be level. If the freezer is

not leveled during installation, the doors may not close or

seal properly, causing cooling, frost, or moisture problems.

•

To level your freezer, rotate the leveling feet clockwise (to

raise) the freezer or counter-clockwise (to lower).

Installing the door handle

1

Unplug the freezer.

2

Screw the extended-head screws into the door holes using

the included wrench. Do not overtighten. The screw heads

should extend above the surface of the door.

3

Place the door handle over the heads of the screws.

4

Install the remaining two screws into the holes in the side

of the handle, then tighten them securely.

Installing the bottom decorative cover

1

Remove the cover plate on the hinge side of the decorative

cover.

2

Install the bottom decorative cover by using the three

screws provided.

INTRODUCING THE

INSIGNIA CONNECT APP

Download the Insignia Connect app

to use additional features such as

open-door and temperature alerts.

App download is optional – your

freezer works normally without it!

FIND YOUR

USER GUIDE

ONLINE!

Go to www.insigniaproducts.com, then click

Support & Service

.

Enter

NS-UZ14XWH7

in the box under

Manual, Firmware, Drivers &

Product Information

, then click

►

.

PACKAGE CONTENTS

• 13.8 cubic foot upright freezer with WiFi connection

• Door handle and screws

• Bottom decorative cover and screws

•

Quick Setup Guide

CONNECTING YOUR FREEZER TO WIFI

(OPTIONAL)

1

Make sure that your mobile device is connected to your

preferred WiFi network.

2

Download and open the free Insignia Connect Device app from

the App Store or Google Play. (Apple: iOS 9 or later, Android:

6.0.1 Marshmallow or later)

3

Log in or sign up for a Best Buy or Insignia Connect Device

account.

4

On your freezer, press and hold

Lock

to unlock the control

panel.

5

Press and hold

-

and

Lock

at the same time until you hear a

beep and see “0” on the control panel.

6

Press

+

until “AP” is displayed.

7

In the app, tap

Set Up Device

, then follow the on-screen

directions to complete setup.

Notes

: The control panel will display the temperature after 10 seconds,

but WiFi pairing mode will remain active.

•

You may need to repeat steps 4-6 to put the freezer back into AP mode

if the app cannot find your freezer.

•

Your freezer uses the 2.4GHz WiFi spectrum. If your router provides

both 2.4GHz and 5GHz, select the 2.4GHz band.

USING YOUR FREEZER

1

Plug in your freezer. Wait for 30 minutes, then open the

freezer door to determine if the freezer is working properly.

2

Press and hold the

Lock

button for three seconds, then

+

or

-

to set the temperature inside the freezer. A beep sounds

when the MAX or MIN temperatures are reached.

Using the Lock button

•

To prevent accidental activation, the control panel

automatically locks after a period of inactivity. To use the

control panel, press and hold the

Lock

button for three

seconds.

Switching between Freezer and Refrigerator modes

This freezer has an advanced design feature that lets you

change it from a freezer to a refrigerator. You can only use the

control panel to switch modes. You cannot use the Insignia

Connect App to switch modes.

1

Press and hold the

Lock

button for three seconds.

2

Press and hold the

Freezer/Fridge

button for three

seconds. The panel beeps and the indicator changes to the

new mode.

Quick Freezing foods

•

The quick freeze mode lowers the temperature below the

normal operating temperature to quickly freeze foods. Press

the

Quick Freeze

button to enter quick freeze mode. The

blue snowflake turns on.

•

The quick freeze mode turns off after three hours if the

temperature falls below -13° F (-25° C). If the temperature

does not fall below -13° F (-25° C), the quick freeze mode

turns off after 24 hours. You can press the button a second

time to exit quick freeze mode.

Switching between Fahrenheit and Celsius

1

Press and hold the

Lock

button for three seconds.

2

Press and hold

+

and

-

at the same time for three seconds.

A beep sounds and the display changes.

Cover plates (remove one)

Insignia NS-CZ18XWH7 Quick Setup Guide

Insignia NS-CZ18XWH7 Manual

Insignia NS-CZ18XWH7 manual content summary: