Insignia NS-WF26FD9-1 Quick Setup Guide
Insignia NS-WF26FD9-1 Manual
 |
View all Insignia NS-WF26FD9-1 manuals
Add to My Manuals
Save this manual to your list of manuals |
Insignia NS-WF26FD9-1 manual content summary:
- Insignia NS-WF26FD9-1 | Quick Setup Guide - Page 1
QUICK SETUP GUIDE Refrigerator Water Filter NS-WF26FD9-1 PACKAGE CONTENTS • Refrigerator water filter • Quick Setup Guide FEATURES • Works with Insignia French Door Refrigerators (NS-RFD26SS9, NS-RFD26CXSS0, NS-RFD21CXSS0, and NS-RFD21CISS0) • NSF 53 certified to remove contaminants, including - Insignia NS-WF26FD9-1 | Quick Setup Guide - Page 2
Health Water Treatment Device Certificate Number #3387 Trademark/Model Designation WF26FD9-1 Replacement Elements NS-WF26FD9-1 The water treatment CONTACT INSIGNIA: For customer service, call 1-877-467-4289 (U.S. and Canada) or 01-800-926-3000 (Mexico) www.insigniaproducts.com INSIGNIA is
-
1 -
2
 |
 |
PACKAGE CONTENTS
• Refrigerator water filter
•
Quick Setup Guide
FEATURES
•
Works with Insignia French Door Refrigerators (NS-RFD26SS9,
NS-RFD26CXSS0, NS-RFD21CXSS0, and NS-RFD21CISS0)
•
NSF 53 certified to remove contaminants, including chlorine,
asbestos, cysts, lead, mercury, o-dichlorobenzene, carbofuran,
benzene, atrazine, and toxaphene
•
Keeps beneficial minerals that are good for your health
•
Improves taste and removes odor for more palatable food and
drinks
•
Lasts up to six months or 300 gallons (1,136 L)
•
Eliminates cloudiness for fresh, clear drinking water
GENERAL INSTALLATION GUIDELINES
•
It is normal for black carbon particles to appear on the outside of your
filter. This happens when the filter is moved during shipping. It is safe,
simply wipe it off.
•
The filter connectors are large to prevent leaks. You might have
to twist the filter hard to make sure the connection is secure.
INSTALLING YOUR WATER FILTER
To drink the freshest and cleanest water from your refrigerator, change
the filter every six months or when the
icon starts blinking.
1
Shut off the water supply, then turn off the water shutoff valve on
your refrigerator.
2
Turn the old water filter about 1/4 turn counter-clockwise, then pull
the filter out of the filter holder. Depending on water impurities, you
may have to pull hard to remove the filter.
Note
: When you pull out the water filter, a little water may leak from the
opening. This is normal. To minimize the water leakage, keep the filter
horizontal when you pull it out.
3
Pull out the water filter tray, then empty the tray. Dry around the filter
opening with a dry cloth, then put the tray back in.
4
Insert the new water filter into the water filter holder.
5
While turning the new filter clockwise, push it all the way into the
holder until it locks into place.
6
Turn on the shutoff valve and the water supply, then run water
through the dispenser until the water runs clear (about five minutes).
This cleans the water supply system and removes any trapped air.
7
Open the refrigerator door and make sure that no water leaks from
the water filter.
Note
: If leaks occur, repeat the installation steps. If leaks persist, discontinue
use and call customer service.
8
After you install the new filter, press and hold both the
On/Off
and
Super Freeze
buttons for about three seconds to turn off the
icon.
Before using your new product, please read these instructions to prevent any damage.
QUICK SETUP GUIDE
Refrigerator
Water Filter
NS-WF26FD9-1
SOLUTION
•
Make sure that you soak your filter in water for 15 minutes before installing.
•
Make sure that the filter is securely connected to the filter holder. Do not use
tools to tighten the filter in place.
•
Make sure that the water line to the refrigerator is turned on. The valve must
be completely open for the refrigerator to receive water.
•
Make sure that the refrigerator door is closed or the dispenser will not work.
•
A few drops are normal. If the water is dripping constantly, have a service
technician check your refrigerator’s water valve.
•
Cloudy water is caused by microscopic air bubbles. Run two to three gallons
of water from your dispenser to clear the air bubbles out.
•
Black carbon particles in the water are normal and appear with all carbon
filters. Run two to three gallons of water through your dispenser to remove
loose carbon particles.
•
Make sure that you soak your filter in water for 15 minutes before installing.
•
Noises and sputtering are caused by trapped air pockets. Run two to three
gallons of water from your dispenser to push the air out.
•
If you do not use your water dispenser for more than four days, run two
gallons of water through the dispenser before using it.
•
Make sure that you replace your filter every six months to prevent bacteria
growth.
PROBLEM
My refrigerator is not
dispensing water
My water dispenser is
dripping
My water is cloudy or
contains black carbon
particles
My new filter is
making noises or
sputtering
My water tastes bad
TROUBLESHOOTING
STORAGE AND MAINTENANCE
•
Replace your filter every six months to prevent bacteria and fungus
growth in your filter, supply lines, and storage tank.
•
Stored filters do not expire. Keep your unused filters in a cool, dark,
and dry place until you need them.
•
If you do not use your water dispenser for more than four days, run
two gallons of water before using it to prevent bad tasting water.