Intel SRCSASLS4I Hardware User Guide

Intel SRCSASLS4I - RAID Controller Manual

Get Intel SRCSASLS4I - RAID Controller PDF manuals and user guides
UPC - 735858201353
View all Intel SRCSASLS4I manuals
Add to My Manuals
Save this manual to your list of manuals

Intel SRCSASLS4I manual content summary:

  • Intel SRCSASLS4I | Hardware User Guide - Page 1
    Intel® RAID Controller SRCSASLS4I Hardware User's Guide Intel Order Number: E33167-002
  • Intel SRCSASLS4I | Hardware User Guide - Page 2
    in the United States and other countries. *Other names and brands may be claimed as the property of others. Copyright © 2007-2008 by Intel Corporation. Portions Copyright 2005-2008 by LSI Logic Corporation. All rights reserved. ii Intel® RAID Controller SRCSASLS4I Hardware User's Guide
  • Intel SRCSASLS4I | Hardware User Guide - Page 3
    hardware guide for the Intel® RAID Controller SRCSASLS4I, which can be used for SAS and SATA disk drives. It contains installation instructions and specifications. For details on how to configure the storage adapters, and for an overview of the software drivers, see the Software User's Guide on
  • Intel SRCSASLS4I | Hardware User Guide - Page 4
    iv Intel® RAID Controller SRCSASLS4I Hardware User's Guide
  • Intel SRCSASLS4I | Hardware User Guide - Page 5
    Installation 7 Requirements ...7 Install the RAID Controller ...7 Configure the RAID Controller 10 Replacing a Controller, Resolving a Config Mismatch 10 Chapter 3, Intel® RAID Controller SRCSASLS4I Characteristics 11 Technical Specifications ...12 Array Performance Features 13 Fault Tolerance
  • Intel SRCSASLS4I | Hardware User Guide - Page 6
    vi Intel® RAID Controller SRCSASLS4I Hardware User's Guide
  • Intel SRCSASLS4I | Hardware User Guide - Page 7
    and cable are easier to manipulate, connect to smaller devices, and do not inhibit airflow. The point-to-point SATA architecture eliminates difficulties created by the legacy ATA master-slave architecture, while maintaining compatibility with existing ATA firmware. Intel® RAID Controller SRCSASLS4I
  • Intel SRCSASLS4I | Hardware User Guide - Page 8
    list for the Intel® RAID Controller SRCSASLS4I to make sure the RAID card supports your operating system. Usability • The card ships with both a standard and a low-profile bracket. • Small, thin cabling with serial point-to-point 3.0 Gbps data transfer rates. • Support for non-disk devices and mixed
  • Intel SRCSASLS4I | Hardware User Guide - Page 9
    to recognize an error and recover if possible. • Failures are logged from controller and drive firmware, and SMART monitor. • Failures are logged in NVRAM, viewable from OS Event Log, Intel® RAID Web Console 2; CIM, LEDs, and via alarm. Intel® RAID Controller SRCSASLS4I Hardware User's Guide 3
  • Intel SRCSASLS4I | Hardware User Guide - Page 10
    one quad port. • Allows addressing of multiple SATA targets through an expander if using SATA 2.0- compliant hard disk drives. • Allows multiple initiators to address a single target (in a fail-over configuration) through an expander. 4 Intel® RAID Controller SRCSASLS4I Hardware User's Guide
  • Intel SRCSASLS4I | Hardware User Guide - Page 11
    , choose Disable Alarm. To enable alarm, choose Enable Alarm To disable alarm only until the next event or until next power cycle, choose Silence Alarm. Intel® RAID Controller SRCSASLS4I Hardware User's Guide 5
  • Intel SRCSASLS4I | Hardware User Guide - Page 12
    6 Intel® RAID Controller SRCSASLS4I Hardware User's Guide
  • Intel SRCSASLS4I | Hardware User Guide - Page 13
    Installation Requirements • The Intel® RAID Controller SRCSASLS4I, with the provided cables. • A host system with an available x8 or x16 PCI-Express* slot. • The Resource CD, which contains drivers and documentation. • SAS or SATA 3.0 hard drives. Note: Intel Corporation strongly recommends using an
  • Intel SRCSASLS4I | Hardware User Guide - Page 14
    length by one foot if using a backplane. Do not use a cross-over cable. Only connect to SAS or SATA drives, SAS or SATA backplanes, or an expander device. Route the cable carefully. Check that controller and cable are all properly attached. 8 Intel® RAID Controller SRCSASLS4I Hardware User's Guide
  • Intel SRCSASLS4I | Hardware User Guide - Page 15
    AF002635 Figure 3. Connecting Cable between the RAID Controller and Drives/Backplane 6. Install the server system cover and connect the power cords. See your server system documentation for instructions. Intel® RAID Controller SRCSASLS4I Hardware User's Guide 9
  • Intel SRCSASLS4I | Hardware User Guide - Page 16
    display the Intel® RAID Controller SRCSASLS4I number and firmware version. The numbering of the RAID controller follows the PCI slot scanning order used by the server board. 3. See the Quick Start User's Guide and the Software User's Guide for instructions to configure the RAID controller and to
  • Intel SRCSASLS4I | Hardware User Guide - Page 17
    signal support for processor in reset for firmware recovery. • No jumper = Normal operational mode. • Jumper = Mode 0 for firmware recovery; requires a firmware recovery utility and firmware image file. Out-of-band enclosure management (SES2) Intel® RAID Controller SRCSASLS4I Hardware User's Guide
  • Intel SRCSASLS4I | Hardware User Guide - Page 18
    Specification Processor Operating voltage Card size Array interface to host SATA bus speed Serial port SAS controller SAS/SATA ports Physical and virtual drive support Cache Firmware Compatible devices Cabling Redundant configuration Enclosure management Enclosure support Intel® RAID Controller
  • Intel SRCSASLS4I | Hardware User Guide - Page 19
    (SMART) support Optional Battery Backup Drive Replacement Drive Rebuild Using Hot Spares Error Checking and Indication Detects up to 70% of predictable disk drive failures and monitors the internal performance of all motors, heads, and drive electronics. Intel® RAID Smart Battery AXXRSBBU6 cache
  • Intel SRCSASLS4I | Hardware User Guide - Page 20
    battery 20-80% 10-90% condensing Safety Characteristics The Intel® RAID Controller SRCSASLS4I meets or exceeds the requirements of UL flammability rating 94 V0. Each bare board is marked with the supplier name or trademark, type, and UL flammability rating. For the boards installed in a PCI bus
  • Intel SRCSASLS4I | Hardware User Guide - Page 21
    inserted properly. 6. Follow the instructions that came with your server system to remove the server cover. 7. Plug in and power on the system. The controller detects the RAID configuration from the configuration data on the drives (COD). Intel® RAID Controller SRCSASLS4I Hardware User's Guide 15
  • Intel SRCSASLS4I | Hardware User Guide - Page 22
    Follow the instructions that came with your server system to remove the server cover. 10. Plug in and power on the system. When you start the system, the controller detects the RAID configuration from the configuration data on the drives. 16 Intel® RAID Controller SRCSASLS4I Hardware User's Guide
  • Intel SRCSASLS4I | Hardware User Guide - Page 23
    peripherals from their power sources. Also disconnect any telephone or telecommunications lines from the computer. • Doing so reduces the potential for personal injury or shock. Intel® RAID Controller SRCSASLS4I Hardware User's Guide 17
  • Intel SRCSASLS4I | Hardware User Guide - Page 24
    connect a cable, make sure both connectors are correctly oriented and aligned. • Handle components and cards with care. Don't touch the components or contacts on a card. Hold a card by its , use antistatic floor pads and workbench pads. 18 Intel® RAID Controller SRCSASLS4I Hardware User's Guide
  • Intel SRCSASLS4I | Hardware User Guide - Page 25
    performing any of the instructions. See also Intel Server Boards and Server Chassis Safety Information on the Resource CD and/or at http:\\support.intel.com\support\motherboards devices cables and the AC power cord(s) to the system. Intel® RAID Controller SRCSASLS4I Hardware User's Guide 19
  • Intel SRCSASLS4I | Hardware User Guide - Page 26
    hierzu auch die Sicherheitshinweise zu Intel-Serverplatinen und -ServergehŠusen auf der Ressourcen-CD oder unter http:\\support.intel.com\support\motherboards\server\sb\cs-010770.htm System niemals ohne ordnungsgemäß montiertes Gehäuse ein. 20 Intel® RAID Controller SRCSASLS4I Hardware User's Guide
  • Intel SRCSASLS4I | Hardware User Guide - Page 27
    einige Platinen und Gehäuseteile scharfe Spitzen und Kanten aufweisen. Arbeiten an Platinen und Gehäuse sollten vorsichtig ausgeführt werden. Sie sollten Schutzhandschuhe tragen. Intel® RAID Controller SRCSASLS4I Hardware User's Guide 21
  • Intel SRCSASLS4I | Hardware User Guide - Page 28
    ème. Pour mettre le système hors tension, vous devez débrancher chaque câble d'alimentation de sa prise. CONSIGNES DE SÉCURITÉ -Lorsque vous ouvrez le boîtier pour accéder à l'inté d'alimentation c. a. et câbles externes au système. 22 Intel® RAID Controller SRCSASLS4I Hardware User's Guide
  • Intel SRCSASLS4I | Hardware User Guide - Page 29
    instruction. Consultez Intel Server Boards and Server Chassis Safety Information sur le CD Resource CD ou bien rendez-vous sur le site http:\\support.intel.com\support\motherboards . 3. Desconecte todos los cables de alimentación CA del Intel® RAID Controller SRCSASLS4I Hardware User's Guide 23
  • Intel SRCSASLS4I | Hardware User Guide - Page 30
    impedir que pueda accederse al mismo sin autorización. 5. Conecte todos los cables externos y los cables de alimentación CA al sistema. Si el sistema ha estado en funcionamiento c.a. dalle prese a muro o dall'alimentazione di corrente. 24 Intel® RAID Controller SRCSASLS4I Hardware User's Guide
  • Intel SRCSASLS4I | Hardware User Guide - Page 31
    dissipatore di calore potrebbero essere surriscaldati. Fare attenzione alla presenza di piedini appuntiti e parti taglienti sulle schede e sul telaio. È consigliabile l'uso di guanti di protezione. Intel® RAID Controller SRCSASLS4I Hardware User's Guide 25
  • Intel SRCSASLS4I | Hardware User Guide - Page 32
    26 Intel® RAID Controller SRCSASLS4I Hardware User's Guide
  • Intel SRCSASLS4I | Hardware User Guide - Page 33
    C: Regulatory and Certification Information This RAID Controller Card complies with the following safety and electromagnetic compatibility (EMC) regulations. Product Safety Compliance (Europe) • VCCI Mark (Japan) • MIC Mark (Korea) Intel® RAID Controller SRCSASLS4I Hardware User's Guide 27
  • Intel SRCSASLS4I | Hardware User Guide - Page 34
    Rules. Operation of this device is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference CLASS B CANADA NMB-003 CLASSE B VCCI Marking (Class B) Japan 28 Intel® RAID Controller SRCSASLS4I Hardware User's Guide
  • Intel SRCSASLS4I | Hardware User Guide - Page 35
    Mark Korea Australia Marking Electromagnetic Compatibility Notices FCC Verification Statement (USA) : This device complies with Part 15 of installed and used in accordance with the instructions, may cause harmful interference to radio Intel® RAID Controller SRCSASLS4I Hardware User's Guide 29
  • Intel SRCSASLS4I | Hardware User Guide - Page 36
    local Intel representative - Name of Certification Recipient: LSI Logic Corporation - Date of Manufacturer: Refer to date code on product - Manuation: LSI Logic Corporation Manufacturer/Nation / Refer to country of origin marked on product 30 Intel® RAID Controller SRCSASLS4I Hardware User's Guide
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
Intel
®
RAID Controller SRCSASLS4I
Hardware User’s Guide
Intel Order Number: E33167-002