Intermec CV41 Universal Vehicle Power Supply Instructions
Intermec CV41 Manual
![]() |
View all Intermec CV41 manuals
Add to My Manuals
Save this manual to your list of manuals |
Intermec CV41 manual content summary:
- Intermec CV41 | Universal Vehicle Power Supply Instructions - Page 1
Universal Vehicle Power Supply 9007AX01 Installation Instructions - Intermec CV41 | Universal Vehicle Power Supply Instructions - Page 2
Smart Mobile Computing, SmartSystems, TE 2000, Trakker Antares, and Vista Powered are either trademarks or registered trademarks of Intermec Technologies Corporation. There are U.S. and foreign patents as well as U.S. and foreign patents pending. ii Universal Power Supply Installation Instructions - Intermec CV41 | Universal Vehicle Power Supply Instructions - Page 3
Battery Cable 7 Connect to the Vehicle Battery 10 Connect to the Top Battery Terminal 11 Connect to the Side Battery Terminal 12 Fasten the Ground Wire 13 CV41 Power Connector Pin Assignments 13 CV61 Power Connector Pin Assignments 14 Universal Power Supply Installation Instructions iii - Intermec CV41 | Universal Vehicle Power Supply Instructions - Page 4
iv Universal Power Supply Installation Instructions - Intermec CV41 | Universal Vehicle Power Supply Instructions - Page 5
power supply kit provides 12 VDC output power that is filtered and regulated for your Intermec vehicle mount or fixed mount computers. Additionally, the power supply provides short circuit, over-voltage, and over-temperature protection. The universal power supply supports these computers: • CV41 - Intermec CV41 | Universal Vehicle Power Supply Instructions - Page 6
guidelines: • Use the cable clamps or wire-ties provided to secure the cables at least every 46 cm (18 in). • Do not secure cables to any moving parts on the vehicle. Make sure the cable is at least 15.2 cm (6 in) away from the exhaust system. 6 Universal Power Supply Installation Instructions - Intermec CV41 | Universal Vehicle Power Supply Instructions - Page 7
(P/N 236-294-001) • CV61 Adapter Cable (P/N VE027-8024-C0) Connecting the Adapter Cable to Y-Cable and the CV61. Assemble the Vehicle Battery Cable Before installing the vehicle battery cable, make sure you follow these installation guidelines: Universal Power Supply Installation Instructions 7 - Intermec CV41 | Universal Vehicle Power Supply Instructions - Page 8
power cable and internal power supply of the CV61. If the fuse fails for any reason, replace it with a new fuse. Replacement Fuse Specifications Fuse Type Volts Amps Specification vehicle power to see if excessive voltage spikes are occuring. 8 Universal Power Supply Installation Instructions - Intermec CV41 | Universal Vehicle Power Supply Instructions - Page 9
jacket. 5 Insert and secure the fuse into the fuse block assembly. 6 Assemble the negative wire: a Strip 0.60 cm (0.25 in) of insulation from the green and white wires. b Twist the wires together. c Crimp a 3/8-inch terminal ring onto the wires. Universal Power Supply Installation Instructions 9 - Intermec CV41 | Universal Vehicle Power Supply Instructions - Page 10
over the braided ground wire. 9 Crimp a 3/8-inch terminal ring onto the braided ground wire. 10 Connect the 4-pin connector to the power supply. 11 Connect the battery cable to the vehicle battery. and radio will return to default settings. 10 Universal Power Supply Installation Instructions - Intermec CV41 | Universal Vehicle Power Supply Instructions - Page 11
washer onto the battery clamp. 5 Thread another 3/8-inch nut onto the battery clamp bolt and tighten the nut securely. 6 Repeat Steps 1 through 5 for the negative wire. 7 Connect the ground wire. For help, see "Fasten the Ground Wire" on page 13. Universal Power Supply Installation Instructions 11 - Intermec CV41 | Universal Vehicle Power Supply Instructions - Page 12
. 8 Tighten the battery terminal post securely. 9 Tigthen the nut installed in Step 2 to secure the washers and cables firmly in place. 10 Repeat Steps 1 through 9 for the negative wire. 11 Connect the ground wire. For help, see the next section. 12 Universal Power Supply Installation Instructions - Intermec CV41 | Universal Vehicle Power Supply Instructions - Page 13
for the CV41 power connector. 4 5 3 6 2 1 Pin Signal 1 Vin+ 2 Vin+ 3 Vin- 4 Vin- 5 GND 6 Ignition Description 10 to 60 nominal DC input + 10 to 60 nominal DC input + Input Input Chassis ground +0 to 60 V to start terminal Universal Power Supply Installation Instructions 13 - Intermec CV41 | Universal Vehicle Power Supply Instructions - Page 14
. • external DC to DC converter. 3 Vin- GND 4 Vin- heater Auxiliary input for heated display power. 5 Vin+ heater Auxiliary input for heated display power. 6 Vin+ 12 to 60 V vehicle power direct input. An external fuse is required. 14 Universal Power Supply Installation Instructions - Intermec CV41 | Universal Vehicle Power Supply Instructions - Page 15
- Intermec CV41 | Universal Vehicle Power Supply Instructions - Page 16
Worldwide Headquarters 6001 36th Avenue West Everett, Washington 98203 U.S.A. tel 425.348.2600 fax 425.355.9551 www.intermec.com © 2012 Intermec Technologies Corporation. All rights reserved. Universal Power Supply Installation Instructions *931-088-002* P/N 931-088-002
![](/manual_guide/products/intermec-cv41-universal-vehicle-power-supply-instructions-2007e5d/1.png)
Universal Vehicle Power Supply
Installation Instructions
9007AX01